Package: linux-image-2.6.26-2-amd64 Version: 2.6.26-19lenny2 Severity: critical Justification: breaks the whole system
On some disk load (over qla2xxx attached disks) the server prints an error and stops (console output attached below). The same kernel with additional parameter pci=nomsi runs with no any problem. -- Package-specific info: ** Version: Linux version 2.6.26-2-amd64 (Debian 2.6.26-19lenny2) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Nov 5 02:23:12 UTC 2009 ** Command line: root=/dev/md1 ro console=ttyS0 pci=nomsi ** Not tainted ** Kernel log: [ 27.101249] ACPI: Power Button (FF) [PWRF] [ 27.155477] input: Power Button (CM) as /class/input/input2 [ 27.220046] EDAC MC: Ver: 2.1.0 Nov 5 2009 [ 27.303732] EDAC MC0: Giving out device to 'i5000_edac.c' 'I5000': DEV 0000:00:10.0 [ 27.394223] EDAC PCI0: Giving out device to module 'i5000_edac' controller 'EDAC PCI controller': DEV '0000:00:10.0' (POLLED) [ 27.659739] ACPI: Power Button (CM) [PWRB] [ 27.740359] tg3.c:v3.92.1 (June 9, 2008) [ 27.787198] ACPI: PCI Interrupt 0000:1e:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 27.896338] PCI: Setting latency timer of device 0000:1e:00.0 to 64 [ 27.904318] intel_rng: FWH not detected [ 27.957061] eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:1b:78:a3:3c:04 [ 28.087945] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1] [ 28.217777] eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 28.280431] ACPI: PCI Interrupt 0000:1f:00.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 28.368896] PCI: Setting latency timer of device 0000:1f:00.0 to 64 [ 28.368872] input: PC Speaker as /class/input/input3 [ 28.409888] eth1: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:1b:78:a3:3c:05 [ 28.409891] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] [ 28.409893] eth1: dma_rwctrl[76180000] dma_mask[64-bit] [ 28.891576] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 29.005148] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19 [ 29.212328] Error: Driver 'pcspkr' is already registered, aborting... [ 29.777999] ata1.00: configured for UDMA/100 [ 29.876317] ata1: EH complete [ 29.924217] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 29.924225] ata2.00: configured for UDMA/100 [ 29.924225] ata2: EH complete [ 30.161445] sd 0:0:0:0: [sda] Write Protect is off [ 30.236991] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 30.237015] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.358530] sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB) [ 30.444842] sd 1:0:0:0: [sdb] Write Protect is off [ 30.502032] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 30.502054] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 31.033228] Adding 7815480k swap on /dev/md3. Priority:-1 extents:1 across:7815480k [ 31.451098] EXT3 FS on md1, internal journal [ 32.210188] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) [ 32.292063] iTCO_wdt: Found a 631xESB/632xESB TCO device (Version=2, TCOBASE=0x1060) [ 32.424999] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 32.565092] QLogic Fibre Channel HBA Driver: 8.02.01-k4 [ 32.627511] ACPI: PCI Interrupt 0000:0b:01.0[A] -> GSI 24 (level, low) -> IRQ 24 [ 32.743210] qla2xxx 0000:0b:01.0: Found an ISP2422, irq 24, iobase 0xffffc20000c52000 [ 32.836803] qla2xxx 0000:0b:01.0: Configuring PCI space... [ 32.903412] qla2xxx 0000:0b:01.0: Configure NVRAM parameters... [ 33.010147] qla2xxx 0000:0b:01.0: Verifying loaded RISC code... [ 33.097421] firmware: requesting ql2400_fw.bin [ 33.408531] qla2xxx 0000:0b:01.0: Allocated (64 KB) for EFT... [ 33.478243] qla2xxx 0000:0b:01.0: Allocated (1413 KB) for firmware dump... [ 33.665758] scsi6 : qla2xxx [ 33.699227] qla2xxx 0000:0b:01.0: [ 33.699227] QLogic Fibre Channel HBA Driver: 8.02.01-k4 [ 33.699227] QLogic HP AE369-60001 - QLA2340 [ 33.699227] ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:0b:01.0 hdma+, host#=6, fw=4.04.09 [IP] [84XX] [ 34.093819] qla2xxx 0000:0b:01.0: LIP reset occured (f700). [ 34.193897] ACPI: PCI Interrupt 0000:0b:01.1[B] -> GSI 25 (level, low) -> IRQ 25 [ 34.293972] qla2xxx 0000:0b:01.1: Found an ISP2422, irq 25, iobase 0xffffc20000c54000 [ 34.387578] qla2xxx 0000:0b:01.1: Configuring PCI space... [ 34.489901] qla2xxx 0000:0b:01.1: Configure NVRAM parameters... [ 34.606863] qla2xxx 0000:0b:01.1: Verifying loaded RISC code... [ 34.938970] qla2xxx 0000:0b:01.1: Allocated (64 KB) for EFT... [ 35.092599] qla2xxx 0000:0b:01.1: Allocated (1413 KB) for firmware dump... [ 35.216869] scsi7 : qla2xxx [ 35.253266] qla2xxx 0000:0b:01.1: [ 35.253266] QLogic Fibre Channel HBA Driver: 8.02.01-k4 [ 35.253266] QLogic HP AE369-60001 - QLA2340 [ 35.253266] ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:0b:01.1 hdma+, host#=7, fw=4.04.09 [IP] [84XX] [ 35.305352] qla2xxx 0000:0b:01.0: LOOP UP detected (4 Gbps). [ 35.485352] qla2xxx 0000:0b:01.1: LIP reset occured (f700). [ 35.716082] device-mapper: uevent: version 1.0.3 [ 35.782401] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: [email protected] [ 36.048024] device-mapper: multipath: version 1.0.5 loaded [ 36.148546] scsi 6:0:0:0: RAID HP HSV200 6200 PQ: 0 ANSI: 5 [ 36.339091] scsi 6:0:1:0: RAID HP HSV200 6200 PQ: 0 ANSI: 5 [ 36.835918] qla2xxx 0000:0b:01.1: LOOP UP detected (4 Gbps). [ 37.437596] scsi 7:0:0:0: RAID HP HSV200 6200 PQ: 0 ANSI: 5 [ 37.633547] scsi 7:0:1:0: RAID HP HSV200 6200 PQ: 0 ANSI: 5 [ 38.407601] kjournald starting. Commit interval 5 seconds [ 38.476493] EXT3 FS on md0, internal journal [ 38.555496] EXT3-fs: mounted filesystem with ordered data mode. [ 38.817899] kjournald starting. Commit interval 5 seconds [ 38.901897] EXT3 FS on md2, internal journal [ 38.971514] EXT3-fs: mounted filesystem with ordered data mode. [ 39.168308] kjournald starting. Commit interval 5 seconds [ 39.307205] EXT3 FS on md4, internal journal [ 39.358506] EXT3-fs: mounted filesystem with ordered data mode. [ 42.814687] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 42.868110] tg3: eth0: Flow control is off for TX and off for RX. [ 44.319223] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 44.427939] tg3: eth1: Flow control is on for TX and on for RX. [ 63.915387] warning: `ntpd' uses 32-bit capabilities (legacy support in use) ** Loaded modules: Module Size Used by dm_multipath 21392 0 dm_mod 58864 1 dm_multipath qla2xxx 173812 0 firmware_class 12544 1 qla2xxx scsi_transport_fc 49668 1 qla2xxx scsi_tgt 17616 1 scsi_transport_fc iTCO_wdt 15696 1 snd_pcm 81800 0 snd_timer 25744 1 snd_pcm snd 63688 2 snd_pcm,snd_timer soundcore 12064 1 snd snd_page_alloc 13072 1 snd_pcm serio_raw 9988 0 i2c_i801 13596 0 shpchp 34208 0 psmouse 42268 0 i2c_core 27936 1 i2c_i801 pcspkr 7040 0 rng_core 8968 0 tg3 97156 0 i5000_edac 12936 0 edac_core 49560 3 i5000_edac pci_hotplug 32056 1 shpchp container 8320 0 button 11680 0 evdev 14208 0 thermal 22688 0 processor 42304 1 thermal fan 9352 0 thermal_sys 17728 3 thermal,processor,fan ahci 33036 10 libata 165600 1 ahci dock 14112 1 libata raid1 24192 5 md_mod 80292 6 raid1 ext3 125072 4 jbd 51240 1 ext3 mbcache 12804 1 ext3 sd_mod 29376 12 scsi_mod 161016 5 qla2xxx,scsi_transport_fc,scsi_tgt,libata,sd_mod ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 5000X Chipset Memory Controller Hub [8086:25c0] (rev 31) Subsystem: Intel Corporation 5000X Chipset Memory Controller Hub [8086:25c0] Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 0 Capabilities: <access denied> 00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 [8086:25f7] (rev 31) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: df900000-dfafffff Prefetchable memory behind bridge: 00000000d1000000-00000000d10fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 [8086:25e3] (rev 31) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:04.0 PCI bridge [0604]: Intel Corporation 5000X Chipset PCI Express x16 Port 4-7 [8086:25fa] (rev 31) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=10, subordinate=10, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 [8086:25e5] (rev 31) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=11, subordinate=11, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:06.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 6 [8086:25e6] (rev 31) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=12, subordinate=12, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:07.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 [8086:25e7] (rev 31) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=13, subordinate=13, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel driver in use: i5000_edac Kernel modules: i5000_edac 00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: i5000_edac 00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: i5000_edac 00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f1] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f3] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f5] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f6] (rev 31) Subsystem: Hewlett-Packard Company Device [103c:31fd] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1c.0 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 [8086:2690] (rev 09) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=1e, subordinate=1e, sec-latency=0 Memory behind bridge: dfb00000-dfbfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 2 [8086:2692] (rev 09) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=1f, subordinate=1f, sec-latency=0 Memory behind bridge: dfc00000-dfcfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d9) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=20, subordinate=20, sec-latency=32 Memory behind bridge: df000000-df8fffff Prefetchable memory behind bridge: 00000000de000000-00000000deffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller [8086:2670] (rev 09) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.2 SATA controller [0106]: Intel Corporation 631xESB/632xESB SATA AHCI Controller [8086:2681] (rev 09) (prog-if 01 [AHCI 1.0]) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 1830 [size=8] Region 1: I/O ports at 1824 [size=4] Region 2: I/O ports at 1828 [size=8] Region 3: I/O ports at 1820 [size=4] Region 4: I/O ports at 1800 [size=32] Region 5: Memory at dff00000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller [8086:269b] (rev 09) Subsystem: Hewlett-Packard Company Device [103c:31fe] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 1840 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c-i801 01:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port [8086:3500] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=01, secondary=02, subordinate=03, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 01:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge [8086:350c] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=01, secondary=0b, subordinate=0b, sec-latency=64 I/O behind bridge: 00002000-00002fff Memory behind bridge: dfa00000-dfafffff Prefetchable memory behind bridge: 00000000d1000000-00000000d10fffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel modules: shpchp 02:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 [8086:3510] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=02, secondary=03, subordinate=03, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 0b:01.0 Fibre Channel [0c04]: QLogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA [1077:2422] (rev 02) Subsystem: QLogic Corp. Device [1077:0148] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 128 (16000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 24 Region 0: I/O ports at 2000 [size=256] Region 1: Memory at dfa00000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at d1000000 [disabled] [size=256K] Capabilities: <access denied> Kernel driver in use: qla2xxx Kernel modules: qla2xxx 0b:01.1 Fibre Channel [0c04]: QLogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA [1077:2422] (rev 02) Subsystem: QLogic Corp. Device [1077:0148] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 128 (16000ns min), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 25 Region 0: I/O ports at 2400 [size=256] Region 1: Memory at dfa01000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at d1040000 [disabled] [size=256K] Capabilities: <access denied> Kernel driver in use: qla2xxx Kernel modules: qla2xxx 1e:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express [14e4:1659] (rev 11) Subsystem: Hewlett-Packard Company Device [103c:3260] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at dfb00000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 1f:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express [14e4:1659] (rev 11) Subsystem: Hewlett-Packard Company Device [103c:3260] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfc00000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 20:02.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) [102b:0522] (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device [103c:31fa] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 128 (4000ns min, 8000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 5 Region 0: Memory at de000000 (32-bit, prefetchable) [size=16M] Region 1: Memory at df800000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at df810000 [disabled] [size=64K] Capabilities: <access denied> -- System Information: Debian Release: 5.0.3 APT prefers stable APT policy: (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 2.6.26-2-amd64 (SMP w/4 CPU cores) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.26-2-amd64 depends on: ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs ii module-init-tools 3.4-1 tools for managing Linux kernel mo linux-image-2.6.26-2-amd64 recommends no packages. Versions of packages linux-image-2.6.26-2-amd64 suggests: ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v pn linux-doc-2.6.26 <none> (no description available) -- debconf information excluded
[93543.093300] qla2xxx 0000:0b:01.0: Mailbox command timeout occured. Issuing ISP abort. [93543.187021] qla2xxx 0000:0b:01.0: Performing ISP error recovery - ha= ffff81022b8985f8. [93544.168312] qla2xxx 0000:0b:01.0: LIP reset occured (f700). [93545.488056] qla2xxx 0000:0b:01.0: LOOP UP detected (4 Gbps). [93545.684498] do_IRQ: 0.184 No irq handler for vector [93545.800455] int3: 0000 [1] SMP [93545.836381] CPU 0 [93545.836381] Modules linked in: dm_round_robin dm_multipath dm_mod qla2xxx firmware_class scsi_transport_fc scsi_tgt iTCO_wdt snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 serio_raw i2c_core container tg3 rng_core pcspkr psmouse shpchp button pci_hotplug i5000_edac edac_core evdev thermal processor fan thermal_sys ahci libata dock raid1 md_mod ext3 jbd mbcache sd_mod scsi_mod [93546.363711] Pid: 0, comm: swapper Not tainted 2.6.26-2-amd64 #1 [93546.451197] RIP: 0010:[<ffffffff8057d0f1>] [<ffffffff8057d0f1>] _sinittext+0xf1/0x140 [93546.558593] RSP: 0000:ffffffff80575f18 EFLAGS: 00000046 [93546.558593] RAX: 0000000000000000 RBX: ffffffff80212c3f RCX: 0000000000000000 [93546.717564] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffff804fbe70 [93546.717564] RBP: 0000000000000000 R08: ffff8100010356a0 R09: 00008fb6f7876db6 [93546.717564] R10: ffff81022b891990 R11: ffffffff8021a827 R12: ffffffffffffffff [93546.717564] R13: ffffffff805a5900 R14: ffffffff805a64c0 R15: 0000000000000000 [93546.717564] FS: 0000000000000000(0000) GS:ffffffff8053c000(0000) knlGS:0000000000000000 [93547.171510] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b [93547.171510] CR2: 00007ffe29eb6218 CR3: 00000001e7c6a000 CR4: 00000000000006e0 [93547.171510] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [93547.171510] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [93547.171510] Process swapper (pid: 0, threadinfo ffffffff80574000, task ffffffff804f9480) [93547.171510] Stack: ffffffff80212c80 0000000000000010 0000000000000246 ffffffff80575f40 [93547.171510] 0000000000000000 ffffffff8020ac79 0000000000000020 ffffffff8057ddd1 [93547.171510] 0000000000000000 ffffffff8058e5d6 ffffffff805a64c0 0000000000675398 [93547.171510] Call Trace: [93547.171510] [<ffffffff80212c80>] mwait_idle+0x41/0x4d [93547.171510] [<ffffffff8020ac79>] cpu_idle+0x89/0xb3 [93547.171510] [93547.171510] [93547.171510] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc [93548.344319] RIP [<ffffffff8057d0f1>] _sinittext+0xf1/0x140 [93548.344319] RSP <ffffffff80575f18> [93548.344319] ---[ end trace f2c19baabbb385ea ]--- [93548.344319] Kernel panic - not syncing: Attempted to kill the idle task!
