On Tue, Sep 27, 2011 at 08:22:23PM +0200, Torsten Crass wrote: > Package: linux-2.6 > Version: 3.0.0-3 > Severity: normal > > Dear Maintainer, > > when trying to figure out which kernel module might be using IRQ 3 > in my Intel D525MW-based system by calling "cat /proc/interrupts", I > get the reply "Killed" on the console, and the messages from [ > 916.033769] onwards show up in the kernel log. When calling "cat > /proc/interrupts" a second time, the system freezes completely, i.e. > it ceases reacting on keystrokes an renders itself inresponsive over > the network. > > Background: I'm trying to get lirc_serial running using the board's > internal serial connector (port 0x02f8, IRQ 3). However, although I > disabled /dev/ttyS1 using "setserial /dev/ttyS1 uart none" (which by > "setserial -g /dev/ttyS1" gets confirmed to be in effect), > lirc_serial complains about port 02f8 being already in use (see [ > 30.600691]) and IRQ 3 being busy ([ 34.175622]). Interestingly, > "cat /proc/ioports" claims the port in question to be unused (see > below), and as for IRQ 3, well... that's the cause for this bug > report.
lirc_serial has several obvious bugs, so I think that is the component at fault. Jarod, please can you look at this and fix the error handling in lirc_serial. Ben. > Regards -- > > Torsten > > > ** Output of cat /proc/ioports > 0000-0cf7 : PCI Bus 0000:00 > 0000-001f : dma1 > 0020-0021 : pic1 > 0040-0043 : timer0 > 0050-0053 : timer1 > 0060-0060 : keyboard > 0064-0064 : keyboard > 0070-0071 : rtc0 > 0080-008f : dma page reg > 00a0-00a1 : pic2 > 00c0-00df : dma2 > 00f0-00ff : fpu > 0295-0296 : pnp 00:06 > 0378-037a : parport0 > 03c0-03df : vesafb > 03f8-03ff : serial > 0400-047f : pnp 00:06 > 0400-0403 : ACPI PM1a_EVT_BLK > 0404-0405 : ACPI PM1a_CNT_BLK > 0408-040b : ACPI PM_TMR > 0410-0415 : ACPI CPU throttle > 0420-0420 : ACPI PM2_CNT_BLK > 0428-042f : ACPI GPE0_BLK > 0500-053f : pnp 00:06 > 0680-06ff : pnp 00:06 > 0cf8-0cff : PCI conf1 > 0d00-ffff : PCI Bus 0000:00 > 1000-1fff : PCI Bus 0000:01 > 1000-10ff : 0000:01:00.0 > 1000-10ff : r8169 > 2000-201f : 0000:00:1f.3 > 2000-201f : i801_smbus > 2020-203f : 0000:00:1d.3 > 2020-203f : uhci_hcd > 2040-205f : 0000:00:1d.2 > 2040-205f : uhci_hcd > 2060-207f : 0000:00:1d.1 > 2060-207f : uhci_hcd > 2080-209f : 0000:00:1d.0 > 2080-209f : uhci_hcd > 20a0-20af : 0000:00:1f.2 > 20a0-20af : ata_piix > 20b0-20b7 : 0000:00:1f.2 > 20b0-20b7 : ata_piix > 20b8-20bf : 0000:00:1f.2 > 20b8-20bf : ata_piix > 20c0-20c7 : 0000:00:02.0 > 20c8-20cb : 0000:00:1f.2 > 20c8-20cb : ata_piix > 20cc-20cf : 0000:00:1f.2 > 20cc-20cf : ata_piix > 3000-3fff : PCI Bus 0000:04 > 4000-4fff : PCI Bus 0000:03 > 5000-5fff : PCI Bus 0000:02 > > > > > -- Package-specific info: > ** Version: > Linux version 3.0.0-1-686-pae (Debian 3.0.0-3) ([email protected]) > (gcc version 4.5.3 (Debian 4.5.3-8) ) #1 SMP Sat Aug 27 16:41:03 UTC > 2011 > > ** Command line: > root=/dev/sda1 ro selinux_init=no quiet vga=785 quiet > > ** Tainted: DC (1152) > * Kernel has oopsed before. > * Module from drivers/staging has been loaded. > > ** Kernel log: > [ 1.969724] sd 0:0:0:0: [sda] Attached SCSI disk > [ 1.973608] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 2.828523] EXT3-fs: barriers not enabled > [ 2.828780] kjournald starting. Commit interval 5 seconds > [ 2.828858] EXT3-fs (sda1): mounted filesystem with ordered data mode > [ 29.182108] udevd[275]: starting version 172 > [ 29.256262] ACPI: acpi_idle registered with cpuidle > [ 29.256328] input: Sleep Button as > /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 > [ 29.256348] ACPI: Sleep Button [SLPB] > [ 29.295947] Monitor-Mwait will be used to enter C-1 state > [ 29.303840] parport_pc 00:09: reported by Plug and Play ACPI > [ 29.303909] parport0: PC-style at 0x378, irq 7 [PCSPP] > [ 29.328822] input: Power Button as > /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 > [ 29.328839] ACPI: Power Button [PWRF] > [ 29.340441] input: PC Speaker as /devices/platform/pcspkr/input/input3 > [ 29.348229] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, > low) -> IRQ 19 > [ 29.349862] [drm] Initialized drm 1.1.0 20060810 > [ 29.374230] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > [ 29.374245] i915 0000:00:02.0: setting latency timer to 64 > [ 29.467028] i915 0000:00:02.0: irq 45 for MSI/MSI-X > [ 29.467040] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). > [ 29.467044] [drm] Driver supports precise vblank timestamp query. > [ 29.491927] vgaarb: device changed decodes: > PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem > [ 29.787248] input: PS/2 Generic Mouse as > /devices/platform/i8042/serio1/input/input4 > [ 29.819971] [drm] initialized overlay support > [ 29.849126] checking generic (d0000000 7f0000) vs hw (d0000000 10000000) > [ 29.849134] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - > removing generic driver > [ 29.849187] Console: switching to colour dummy device 80x25 > [ 29.849944] fbcon: inteldrmfb (fb0) is primary device > [ 29.889715] [drm] Changing LVDS panel from (+hsync, +vsync) to > (-hsync, -vsync) > [ 29.928563] fixme: max PWM is zero. > [ 29.928582] Console: switching to colour frame buffer device 128x48 > [ 29.936767] fb0: inteldrmfb frame buffer device > [ 29.936772] drm: registered panic notifier > [ 29.936793] No ACPI video bus found > [ 29.936926] [drm] Initialized i915 1.6.0 20080730 for > 0000:00:02.0 on minor 0 > [ 29.937023] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, > low) -> IRQ 22 > [ 29.937134] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X > [ 29.937193] HDA Intel 0000:00:1b.0: setting latency timer to 64 > [ 29.977762] hda_codec: ALC662 rev1: BIOS auto-probing. > [ 29.981897] input: HDA Intel Headphone as > /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 > [ 30.471657] Adding 2046972k swap on /dev/sda2. Priority:-1 > extents:1 across:2046972k > [ 30.527518] EXT3-fs (sda1): using internal journal > [ 30.567442] loop: module loaded > [ 30.599137] lirc_dev: IR Remote Control driver registered, major 251 > [ 30.599751] lirc_serial: module is from the staging directory, > the quality is unknown, you have been warned. > [ 30.600691] lirc_serial: port 02f8 already in use > [ 30.600815] lirc_serial: use 'setserial /dev/ttySX uart none' > [ 30.600822] lirc_serial: or compile the serial port driver as module and > [ 30.600828] lirc_serial: make sure this module is loaded first > [ 31.279418] EXT3-fs: barriers not enabled > [ 31.279722] kjournald starting. Commit interval 5 seconds > [ 31.281226] EXT3-fs (sda3): using internal journal > [ 31.281235] EXT3-fs (sda3): mounted filesystem with ordered data mode > [ 32.567762] r8169 0000:01:00.0: eth0: link down > [ 32.567779] r8169 0000:01:00.0: eth0: link down > [ 32.568203] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 32.580998] fuse init (API version 7.16) > [ 34.171810] lirc_serial: module is from the staging directory, > the quality is unknown, you have been warned. > [ 34.175622] lirc_serial: IRQ 3 busy > [ 34.362895] r8169 0000:01:00.0: eth0: link up > [ 34.363351] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 38.800981] [drm] Changing LVDS panel from (-hsync, -vsync) to > (+hsync, +vsync) > [ 45.264019] eth0: no IPv6 routers present > [ 916.033769] BUG: unable to handle kernel paging request at f83992be > [ 916.034037] IP: [<c1158bc0>] strnlen+0x6/0x16 > [ 916.034219] *pdpt = 000000000148b001 *pde = 000000003541a067 *pte > = 0000000000000000 > [ 916.034537] Oops: 0000 [#1] SMP > [ 916.034676] Modules linked in: binfmt_misc fuse lirc_dev > firewire_sbp2 firewire_core crc_itu_t loop snd_hda_codec_realtek > snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss > snd_pcm snd_seq_midi snd_rawmidi i915 snd_seq_midi_event psmouse > evdev serio_raw drm_kms_helper i2c_i801 snd_seq drm pcspkr > i2c_algo_bit snd_timer snd_seq_device parport_pc parport snd button > i2c_core video processor thermal_sys soundcore snd_page_alloc ext3 > jbd mbcache sg sd_mod crc_t10dif ata_generic ata_piix libata > scsi_mod r8169 mii uhci_hcd ehci_hcd usbcore [last unloaded: > scsi_wait_scan] > [ 916.036417] > [ 916.036417] Pid: 2973, comm: cat Tainted: G C > 3.0.0-1-686-pae #1 /D525MW > [ 916.036417] EIP: 0060:[<c1158bc0>] EFLAGS: 00010097 CPU: 3 > [ 916.036417] EIP is at strnlen+0x6/0x16 > [ 916.036417] EAX: f83992be EBX: f4f69117 ECX: f83992be EDX: fffffffe > [ 916.036417] ESI: f4f6a000 EDI: f83992be EBP: ffffffff ESP: f4eb1e9c > [ 916.036417] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 > [ 916.036417] Process cat (pid: 2973, ti=f4eb0000 task=f40ae8e0 > task.ti=f4eb0000) > [ 916.036417] Stack: > [ 916.036417] c1156f93 f4eb1f00 f4eb1f04 f4f69117 f4f69117 > c1157b73 ffffff00 ffffffff > [ 916.036417] 0000ffff f4f6a000 f4f69115 00000eeb c13528f5 > ff0a0004 ffffffff f4f79440 > [ 916.036417] f4967840 c13c6d00 00000020 c10de89f f4eb1f00 > f4f79440 c1078580 f4f79440 > [ 916.036417] Call Trace: > [ 916.036417] [<c1156f93>] ? string.clone.2+0x28/0x6d > [ 916.036417] [<c1157b73>] ? vsnprintf+0x144/0x261 > [ 916.036417] [<c10de89f>] ? seq_printf+0x22/0x3d > [ 916.036417] [<c1078580>] ? show_interrupts+0x1ca/0x1fa > [ 916.036417] [<c10dec24>] ? seq_read+0x247/0x31d > [ 916.036417] [<c10de9dd>] ? seq_lseek+0x123/0x123 > [ 916.036417] [<c10ff811>] ? proc_reg_read+0x53/0x67 > [ 916.036417] [<c10ff7be>] ? proc_reg_write+0x67/0x67 > [ 916.036417] [<c10ca43f>] ? vfs_read+0x7e/0xd3 > [ 916.036417] [<c10969f4>] ? sys_fadvise64_64+0x1ec/0x1f6 > [ 916.036417] [<c10ca4d0>] ? sys_read+0x3c/0x60 > [ 916.036417] [<c12b245f>] ? sysenter_do_call+0x12/0x28 > [ 916.036417] Code: 0e 89 c7 89 d0 f2 ae 74 05 bf 01 00 00 00 4f 89 > f8 5f c3 85 c9 57 89 c7 74 07 89 d0 f2 ae 75 01 4f 89 f8 5f c3 89 c1 > 89 c8 eb 06 > [ 916.036417] 38 00 74 07 40 4a 83 fa ff 75 f4 29 c8 c3 90 57 83 c9 ff 56 > [ 916.036417] EIP: [<c1158bc0>] strnlen+0x6/0x16 SS:ESP 0068:f4eb1e9c > [ 916.036417] CR2: 00000000f83992be > [ 916.244997] [drm] Changing LVDS panel from (+hsync, +vsync) to > (-hsync, -vsync) > [ 916.385979] ---[ end trace 45909bb719f3e475 ]--- > > ** Model information > not available > > ** Loaded modules: > Module Size Used by > binfmt_misc 12880 1 > fuse 56331 1 > lirc_dev 12803 0 > firewire_sbp2 17722 0 > firewire_core 42778 1 firewire_sbp2 > crc_itu_t 12331 1 firewire_core > loop 17866 0 > snd_hda_codec_realtek 206339 1 > snd_hda_intel 21691 0 > snd_hda_codec 58364 2 snd_hda_codec_realtek,snd_hda_intel > snd_hwdep 12936 1 snd_hda_codec > snd_pcm_oss 36377 0 > snd_mixer_oss 17713 1 snd_pcm_oss > snd_pcm 53315 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss > snd_seq_midi 12744 0 > snd_rawmidi 22621 1 snd_seq_midi > i915 294451 3 > snd_seq_midi_event 13124 1 snd_seq_midi > psmouse 46216 0 > evdev 12995 7 > serio_raw 12734 0 > drm_kms_helper 22688 1 i915 > i2c_i801 12670 0 > snd_seq 39539 2 snd_seq_midi,snd_seq_midi_event > drm 129847 4 i915,drm_kms_helper > pcspkr 12515 0 > i2c_algo_bit 12722 1 i915 > snd_timer 22027 2 snd_pcm,snd_seq > snd_seq_device 12985 3 snd_seq_midi,snd_rawmidi,snd_seq > parport_pc 22059 0 > parport 27241 1 parport_pc > snd 38562 11 > snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > button 12810 1 i915 > i2c_core 19141 5 > i915,drm_kms_helper,i2c_i801,drm,i2c_algo_bit > video 17475 1 i915 > processor 27382 0 > thermal_sys 17677 2 video,processor > soundcore 12992 1 snd > snd_page_alloc 12899 2 snd_hda_intel,snd_pcm > ext3 99597 2 > jbd 42027 1 ext3 > mbcache 12898 1 ext3 > sg 21564 0 > sd_mod 35493 4 > crc_t10dif 12332 1 sd_mod > ata_generic 12439 0 > ata_piix 21110 3 > libata 133339 2 ata_generic,ata_piix > scsi_mod 135178 4 firewire_sbp2,sg,sd_mod,libata > r8169 37326 0 > mii 12595 1 r8169 > uhci_hcd 22275 0 > ehci_hcd 35401 0 > usbcore 104234 3 uhci_hcd,ehci_hcd > > ** Network interface configuration: > > auto lo > iface lo inet loopback > > allow-hotplug eth0 > iface eth0 inet dhcp > > ** Network status: > *** IP interfaces and addresses: > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > inet 127.0.0.1/8 scope host lo > inet6 ::1/128 scope host > valid_lft forever preferred_lft forever > 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state UP qlen 1000 > link/ether 38:60:77:1b:ea:97 brd ff:ff:ff:ff:ff:ff > inet 192.168.0.11/24 brd 192.168.0.255 scope global eth0 > inet6 fe80::3a60:77ff:fe1b:ea97/64 scope link > valid_lft forever preferred_lft forever > > *** Device statistics: > Inter-| Receive | Transmit > face |bytes packets errs drop fifo frame compressed > multicast|bytes packets errs drop fifo colls carrier compressed > lo: 91375916 17873 0 0 0 0 0 0 > 91375916 17873 0 0 0 0 0 0 > eth0: 17972793 37909 0 0 0 0 0 0 > 80993674 67356 0 0 0 0 0 0 > > *** Protocol statistics: > Ip: > 54870 total packets received > 0 forwarded > 0 incoming packets discarded > 54870 incoming packets delivered > 85176 requests sent out > Icmp: > 0 ICMP messages received > 0 input ICMP message failed. > ICMP input histogram: > 0 ICMP messages sent > 0 ICMP messages failed > ICMP output histogram: > Tcp: > 57 active connections openings > 32 passive connection openings > 6 failed connection attempts > 4 connection resets received > 8 connections established > 54579 segments received > 87093 segments send out > 0 segments retransmited > 0 bad segments received. > 51 resets sent > Udp: > 318 packets received > 0 packets to unknown port received. > 0 packet receive errors > 191 packets sent > UdpLite: > TcpExt: > 4 invalid SYN cookies received > 32 TCP sockets finished time wait in fast timer > 418 delayed acks sent > 6 packets directly queued to recvmsg prequeue. > 30073 packet headers predicted > 4708 acknowledgments not containing data payload received > 26641 predicted acknowledgments > 2 connections reset due to early user close > IpExt: > InMcastPkts: 94 > OutMcastPkts: 75 > InBcastPkts: 103 > OutBcastPkts: 30 > InOctets: 108793938 > OutOctets: 171421247 > InMcastOctets: 32733 > OutMcastOctets: 24991 > InBcastOctets: 15738 > OutBcastOctets: 3684 > > > ** PCI devices: > 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge > [8086:a000] (rev 02) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > Kernel driver in use: agpgart-intel > > 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 > Family Integrated Graphics Controller [8086:a001] (rev 02) (prog-if > 00 [VGA controller]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 45 > Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=512K] > Region 1: I/O ports at 20c0 [size=8] > Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] > Region 3: Memory at e0100000 (32-bit, non-prefetchable) [size=1M] > Expansion ROM at <unassigned> [disabled] > Capabilities: <access denied> > Kernel driver in use: i915 > > 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High > Definition Audio Controller [8086:27d8] (rev 01) > Subsystem: Intel Corporation Device [8086:d625] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 46 > Region 0: Memory at e0280000 (64-bit, non-prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: HDA Intel > > 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI > Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00001000-00001fff > Memory behind bridge: e0f00000-e12fffff > Prefetchable memory behind bridge: 00000000e0000000-00000000e00fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI > Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: 00005000-00005fff > Memory behind bridge: e0b00000-e0cfffff > Prefetchable memory behind bridge: 00000000e0d00000-00000000e0efffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI > Express Port 3 [8086:27d4] (rev 01) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: 00004000-00004fff > Memory behind bridge: e0700000-e08fffff > Prefetchable memory behind bridge: 00000000e0900000-00000000e0afffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI > Express Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: 00003000-00003fff > Memory behind bridge: e0300000-e04fffff > Prefetchable memory behind bridge: 00000000e0500000-00000000e06fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family > USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 23 > Region 4: I/O ports at 2080 [size=32] > Kernel driver in use: uhci_hcd > > 00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family > USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 19 > Region 4: I/O ports at 2060 [size=32] > Kernel driver in use: uhci_hcd > > 00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family > USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin C routed to IRQ 18 > Region 4: I/O ports at 2040 [size=32] > Kernel driver in use: uhci_hcd > > 00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family > USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin D routed to IRQ 16 > Region 4: I/O ports at 2020 [size=32] > Kernel driver in use: uhci_hcd > > 00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family > USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at e0284400 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ehci_hcd > > 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge > [8086:2448] (rev e1) (prog-if 01 [Subtractive decode]) > Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > > 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC > Controller [8086:27bc] (rev 01) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > > 00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA > IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO > PriP PriO]) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 18 > Region 0: I/O ports at 20b8 [size=8] > Region 1: I/O ports at 20cc [size=4] > Region 2: I/O ports at 20b0 [size=8] > Region 3: I/O ports at 20c8 [size=4] > Region 4: I/O ports at 20a0 [size=16] > Region 5: Memory at e0284000 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ata_piix > > 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus > Controller [8086:27da] (rev 01) > Subsystem: Intel Corporation Device [8086:574d] > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin B routed to IRQ 19 > Region 4: I/O ports at 2000 [size=32] > Kernel driver in use: i801_smbus > > 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. > RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] > (rev 06) > Subsystem: Intel Corporation Device [8086:d625] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 44 > Region 0: I/O ports at 1000 [size=256] > Region 2: Memory at e0004000 (64-bit, prefetchable) [size=4K] > Region 4: Memory at e0000000 (64-bit, prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: r8169 > > > ** USB devices: > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > > > -- System Information: > Debian Release: wheezy/sid > APT prefers unstable > APT policy: (500, 'unstable'), (500, 'testing'), (500, 'stable') > Architecture: i386 (i686) > > Kernel: Linux 3.0.0-1-686-pae (SMP w/4 CPU cores) > Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) > Shell: /bin/sh linked to /bin/dash > > Versions of packages linux-image-3.0.0-1-686-pae depends on: > ii debconf [debconf-2.0] 1.5.41 > ii initramfs-tools [linux-initramfs-tool] 0.99 > ii linux-base 3.3 > ii module-init-tools 3.16-1 > > Versions of packages linux-image-3.0.0-1-686-pae recommends: > ii firmware-linux-free 3 > ii libc6-i686 2.13-21 > > Versions of packages linux-image-3.0.0-1-686-pae suggests: > pn grub-pc | extlinux | lilo <none> > pn linux-doc-3.0.0 <none> > > Versions of packages linux-image-3.0.0-1-686-pae is related to: > pn firmware-bnx2 <none> > pn firmware-bnx2x <none> > pn firmware-ipw2x00 <none> > pn firmware-ivtv <none> > pn firmware-iwlwifi <none> > pn firmware-linux <none> > pn firmware-linux-nonfree <none> > pn firmware-qlogic <none> > pn firmware-ralink <none> > pn xen-hypervisor <none> > > -- debconf information: > linux-image-3.0.0-1-686-pae/postinst/ignoring-ramdisk: > linux-image-3.0.0-1-686-pae/postinst/missing-firmware-3.0.0-1-686-pae: > > linux-image-3.0.0-1-686-pae/prerm/removing-running-kernel-3.0.0-1-686-pae: > true > > linux-image-3.0.0-1-686-pae/postinst/depmod-error-initrd-3.0.0-1-686-pae: > false > > > > -- > To UNSUBSCRIBE, email to [email protected] > with a subject of "unsubscribe". Trouble? Contact [email protected] > Archive: http://lists.debian.org/[email protected] > > -- Ben Hutchings We get into the habit of living before acquiring the habit of thinking. - Albert Camus -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
