Your message dated Mon, 17 Oct 2011 07:57:09 -0500
with message-id <[email protected]>
and subject line Re: linux-image-2.6.32-5-686: wastes > 8s of boot time on
something USB related that fails
has caused the Debian Bug report #607574,
regarding linux-image-2.6.32-5-686: wastes > 8s of boot time on something USB
related that fails
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)
--
607574: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=607574
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-29
Severity: normal
[ 16.409864]
/build/buildd-linux-2.6_2.6.32-29-i386-Of6Yt1/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/hid/usbhid/hid-core.c:
usb_submit_urb(ctrl) failed
note the time on the previous log messages
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-29) ([email protected]) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Fri Dec 10 16:12:40 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID- ro quiet
** Not tainted
** Kernel log:
[ 2.201885] scsi2 : SCSI emulation for USB Mass Storage devices
[ 2.202131] usbcore: registered new interface driver usb-storage
[ 2.202136] USB Mass Storage support registered.
[ 2.202394] usb-storage: device found at 2
[ 2.202398] usb-storage: waiting for device to settle before scanning
[ 2.312330] ata1.00: n_sectors mismatch 39062500 != 39102336
[ 2.312335] ata1.00: new n_sectors matches native, probably late HPA unlock,
n_sectors updated
[ 2.329309] ata1.00: configured for UDMA/100
[ 2.329320] ata1: EH complete
[ 2.329663] sd 0:0:0:0: [sda] 39102336 512-byte logical blocks: (20.0
GB/18.6 GiB)
[ 2.329933] sda: detected capacity change from 20000000000 to 20020396032
[ 2.329942] sda: sda1 sda2
[ 2.372787] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.432691] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 2.432699] Uniform CD-ROM driver Revision: 3.20
[ 2.432895] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.447078] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.448100] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.624034] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 2.682281] PM: Starting manual resume from disk
[ 2.682289] PM: Resume from partition 8:2
[ 2.682292] PM: Checking hibernation image.
[ 2.682543] PM: Error -22 checking image file
[ 2.682547] PM: Resume from disk failed.
[ 2.724026] kjournald starting. Commit interval 5 seconds
[ 2.724046] EXT3-fs: mounted filesystem with ordered data mode.
[ 2.840323] usb 4-1: New USB device found, idVendor=1c4f, idProduct=0002
[ 2.840330] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.840336] usb 4-1: Product: USB Keykoard
[ 2.840340] usb 4-1: Manufacturer: USB
[ 2.840525] usb 4-1: configuration #1 chosen from 1 choice
[ 3.080022] usb 4-2: new low speed USB device using uhci_hcd and address 3
[ 3.255274] usb 4-2: New USB device found, idVendor=046d, idProduct=c016
[ 3.255281] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.255286] usb 4-2: Product: Optical USB Mouse
[ 3.255290] usb 4-2: Manufacturer: Logitech
[ 3.255461] usb 4-2: configuration #1 chosen from 1 choice
[ 5.037672] udev[240]: starting version 164
[ 5.565664] input: PC Speaker as /devices/platform/pcspkr/input/input0
[ 5.642637] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.751548] processor LNXCPU:00: registered as cooling_device0
[ 5.855502] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 5.855526] ACPI: Power Button [VBTN]
[ 5.855803] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.855812] ACPI: Power Button [PWRF]
[ 5.862743] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.914946] intel_rng: FWH not detected
[ 5.987405] parport_pc 00:08: reported by Plug and Play ACPI
[ 5.987463] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 6.252700] dcdbas dcdbas: Dell Systems Management Base Driver (version
5.6.0-3.2)
[ 6.381631] usbcore: registered new interface driver hiddev
[ 6.396638] input: USB USB Keykoard as
/devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input3
[ 6.397771] generic-usb 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10
Keyboard [USB USB Keykoard] on usb-0000:00:1d.2-1/input0
[ 6.685861] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 6.760622] [drm] Initialized drm 1.1.0 20060810
[ 6.987208] Error: Driver 'pcspkr' is already registered, aborting...
[ 7.073480] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 7.073551] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 7.200263] usb-storage: device scan complete
[ 7.200863] scsi 2:0:0:0: Direct-Access SAMSUNG HD103UI
PQ: 0 ANSI: 2 CCS
[ 7.202652] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 7.203477] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00
TB/931 GiB)
[ 7.204231] sd 2:0:0:0: [sdb] Write Protect is off
[ 7.204239] sd 2:0:0:0: [sdb] Mode Sense: 28 00 00 00
[ 7.204244] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 7.205846] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 7.205914] sdb: sdb1 sdb2
[ 7.208832] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 7.208900] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 7.444032] intel8x0_measure_ac97_clock: measured 52535 usecs (2531 samples)
[ 7.444049] intel8x0: clocking to 48000
[ 7.445739] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.445750] i915 0000:00:02.0: setting latency timer to 64
[ 7.512122] [drm] set up 7M of stolen space
[ 7.550673] [drm] initialized overlay support
[ 7.793973] Console: switching to colour frame buffer device 200x75
[ 7.808040] fb0: inteldrmfb frame buffer device
[ 7.808044] registered panic notifier
[ 7.808651] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 16.409864]
/build/buildd-linux-2.6_2.6.32-29-i386-Of6Yt1/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/hid/usbhid/hid-core.c:
usb_submit_urb(ctrl) failed
[ 16.410069] generic-usb 0003:1C4F:0002.0002: timeout initializing reports
[ 16.410324] input: USB USB Keykoard as
/devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input4
[ 16.410495] generic-usb 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10
Device [USB USB Keykoard] on usb-0000:00:1d.2-1/input1
[ 16.423820] input: Logitech Optical USB Mouse as
/devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5
[ 16.425897] generic-usb 0003:046D:C016.0003: input,hidraw2: USB HID v1.10
Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.2-2/input0
[ 16.425963] usbcore: registered new interface driver usbhid
[ 16.426319] usbhid: v2.6:USB HID core driver
[ 17.466027] Adding 506036k swap on /dev/sda2. Priority:-1 extents:1
across:506036k
[ 17.788779] EXT3 FS on sda1, internal journal
[ 18.012124] loop: module loaded
[ 20.963874] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.964404] e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 20.964826] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.491912] PPP generic driver version 2.4.2
[ 21.850906] NET: Registered protocol family 24
[ 23.380200] usbcore: registered new interface driver usblp
[ 24.276978] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 30.196308] lp0: using parport0 (interrupt-driven).
[ 30.270603] ppdev: user-space parallel port driver
[ 31.016017] eth0: no IPv6 routers present
** Model information
not available
** Loaded modules:
Module Size Used by
ppdev 4058 0
lp 5570 0
xt_TCPMSS 2303 1
xt_tcpmss 1017 1
xt_tcpudp 1743 1
iptable_mangle 2325 1
ip_tables 7690 1 iptable_mangle
x_tables 8327 4 xt_TCPMSS,xt_tcpmss,xt_tcpudp,ip_tables
usblp 7899 0
pppoe 6849 2
pppox 1242 1 pppoe
ppp_generic 16359 6 pppoe,pppox
slhc 3691 1 ppp_generic
loop 9765 0
joydev 6739 0
i915 222064 2
snd_intel8x0 19595 2
snd_ac97_codec 79148 1 snd_intel8x0
ac97_bus 710 1 snd_ac97_codec
drm_kms_helper 18301 1 i915
snd_pcm_oss 28671 0
snd_mixer_oss 10461 1 snd_pcm_oss
snd_pcm 47222 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
drm 112088 3 i915,drm_kms_helper
i2c_i801 6462 0
i2c_algo_bit 3497 1 i915
snd_timer 12258 1 snd_pcm
usbhid 28008 0
snd 34375 10
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
dcdbas 3892 0
i2c_core 12696 5 i915,drm_kms_helper,drm,i2c_i801,i2c_algo_bit
hid 50873 1 usbhid
soundcore 3450 1 snd
snd_page_alloc 5045 2 snd_intel8x0,snd_pcm
parport_pc 15799 1
parport 22554 3 ppdev,lp,parport_pc
evdev 5609 9
video 14605 1 i915
shpchp 21220 0
button 3598 1 i915
psmouse 44657 0
output 1204 1 video
rng_core 2178 0
processor 26327 0
pci_hotplug 18065 1 shpchp
serio_raw 2916 0
pcspkr 1207 0
ext3 94204 1
jbd 32169 1 ext3
mbcache 3762 1 ext3
sg 15968 0
sr_mod 10770 0
usb_storage 30541 0
cdrom 26487 1 sr_mod
sd_mod 25969 3
crc_t10dif 1012 1 sd_mod
ata_generic 2067 0
ata_piix 17736 2
uhci_hcd 16057 0
thermal 9206 0
libata 115753 2 ata_generic,ata_piix
e1000 77317 0
floppy 40923 0
ehci_hcd 27851 0
thermal_sys 9378 3 video,processor,thermal
scsi_mod 101421 5 sg,sr_mod,usb_storage,sd_mod,libata
usbcore 98453 6 usblp,usbhid,usb_storage,uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM
Controller/Host-Hub Interface [8086:2560] (rev 01)
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation
82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device [8086:2562] (rev
01) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:0126]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at ff680000 (32-bit, non-prefetchable) [size=512K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00
[UHCI])
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ff80 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00
[UHCI])
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at ff60 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) (prog-if 00
[UHCI])
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ff40 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2
EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI])
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at ffa00800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: ff800000-ff9fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC
Interface Bridge [8086:24c0] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801DB (ICH4) IDE Controller
[8086:24cb] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
SMBus Controller [8086:24c3] (rev 01)
Subsystem: Dell Optiplex GX260 [1028:0126]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at dc80 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01)
Subsystem: Dell Device [1028:0126]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc40 [size=64]
Region 2: Memory at ffa00400 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at ffa00000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
01:0c.0 Ethernet controller [0200]: Intel Corporation 82540EM Gigabit Ethernet
Controller [8086:100e] (rev 02)
Subsystem: Dell Optiplex GX260 [1028:002e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at ff8e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ecc0 [size=64]
Capabilities: <access denied>
Kernel driver in use: e1000
** USB devices:
Bus 004 Device 003: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse
Bus 004 Device 002: ID 1c4f:0002 SiGma Micro
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 152d:2338 JMicron Technology Corp. / JMicron USA
Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs
ii linux-base 2.6.32-29 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-29 Binary firmware for various driver
ii libc6-i686 2.11.2-7 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub 0.97-63 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information excluded
--- End Message ---
--- Begin Message ---
Version: 3.1.0~rc4-1~experimental.1
Jonathan Nieder wrote:
> Mario wrote:
>> Version: 2.6.32-29
[...]
>> [ 7.808651] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on
>> minor 0
>> [ 16.409864]
>> /build/buildd-linux-2.6_2.6.32-29-i386-Of6Yt1/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/hid/usbhid/hid-core.c:
>> usb_submit_urb(ctrl) failed
>> [ 16.410069] generic-usb 0003:1C4F:0002.0002: timeout initializing reports
> [...]
>> Bus 004 Device 002: ID 1c4f:0002 SiGma Micro
Should be fixed by v3.1-rc4~47^2^2 (HID: usbhid: Add support for SiGma
Micro chip, 2011-08-23). Mario, can you confirm[1]? Greg et al, does
this patch look like a reasonable candidate for the linux-2.6.32.y
tree?
-- >8 --
From: Jeremiah Matthey <[email protected]>
Date: Tue, 23 Aug 2011 09:44:30 +0200
Subject: HID: usbhid: Add support for SiGma Micro chip
commit f5e4282586dc0c9dab8c7d32e6c43aa07f68586b upstream.
Patch to add SiGma Micro-based keyboards (1c4f:0002) to hid-quirks.
These keyboards dont seem to allow the records to be initialized, and hence a
timeout occurs when the usbhid driver attempts to initialize them. The patch
just adds the signature for these keyboards to the hid-quirks list with the
setting HID_QUIRK_NO_INIT_REPORTS. This removes the 5-10 second wait for the
timeout to occur.
Signed-off-by: Jeremiah Matthey <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Jonathan Nieder <[email protected]>
---
[1] by testing the kernel from experimental[3], or even better, by building
a 2.6.32.y kernel with this patch applied[2]
[2]
http://kernel-handbook.alioth.debian.org/ch-common-tasks.html#s-kernel-org-package
[3] http://wiki.debian.org/DebianExperimental
drivers/hid/hid-ids.h | 3 +++
drivers/hid/usbhid/hid-quirks.c | 1 +
2 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index aef92bbe2cd5..216b285b67f1 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -389,6 +389,9 @@
#define USB_VENDOR_ID_SAMSUNG 0x0419
#define USB_DEVICE_ID_SAMSUNG_IR_REMOTE 0x0001
+#define USB_VENDOR_ID_SIGMA_MICRO 0x1c4f
+#define USB_DEVICE_ID_SIGMA_MICRO_KEYBOARD 0x0002
+
#define USB_VENDOR_ID_SONY 0x054c
#define USB_DEVICE_ID_SONY_VAIO_VGX_MOUSE 0x024b
#define USB_DEVICE_ID_SONY_PS3_CONTROLLER 0x0268
diff --git a/drivers/hid/usbhid/hid-quirks.c b/drivers/hid/usbhid/hid-quirks.c
index 64c5dee27106..08a02abfca91 100644
--- a/drivers/hid/usbhid/hid-quirks.c
+++ b/drivers/hid/usbhid/hid-quirks.c
@@ -65,6 +65,7 @@ static const struct hid_blacklist {
{ USB_VENDOR_ID_WISEGROUP_LTD, USB_DEVICE_ID_SMARTJOY_DUAL_PLUS,
HID_QUIRK_NOGET | HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_WISEGROUP_LTD2, USB_DEVICE_ID_SMARTJOY_DUAL_PLUS,
HID_QUIRK_NOGET | HID_QUIRK_MULTI_INPUT },
+ { USB_VENDOR_ID_SIGMA_MICRO, USB_DEVICE_ID_SIGMA_MICRO_KEYBOARD,
HID_QUIRK_NO_INIT_REPORTS },
{ 0, 0 }
};
--
1.7.7
--- End Message ---
