Package: linux-2.6 Version: 2.6.32-38 Severity: normal Tags: upstream
I have tried - "post-down /sbin/ethtool -s $IFACE wol g" in /etc/network/interfaces - "NETDOWN=no" in /etc/default/halt I can see the network card remaining on upon shutdown. The LEDs flash when I send the WOL magic packet, but the computer does not wake. The same set-up, when booting and then shutting down Windows XP, wakes the computer without problems, so I am sure there is no issue with motherboard bios settings or magic packet. There is another recent report by another user that the sky2 driver is broken for the same Marvell 88E8053 ethernet chip: http://lkml.org/lkml/2011/11/2/143 I would be grateful for a solution. Kind Regards Nick -- Package-specific info: ** Version: Linux version 2.6.32-5-686 (Debian 2.6.32-38) ([email protected]) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Oct 3 04:15:24 UTC 2011 ** Command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/md1_crypt ro quiet nomodeset ** Not tainted ** Kernel log: [ 2.274220] usb 3-2: New USB device found, idVendor=413c, idProduct=2003 [ 2.274223] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.274226] usb 3-2: Product: Dell USB Keyboard [ 2.274228] usb 3-2: Manufacturer: Dell [ 2.274317] usb 3-2: configuration #1 chosen from 1 choice [ 2.284003] raid6: mmxx1 2458 MB/s [ 2.308568] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input1 [ 2.308614] generic-usb 0003:413C:2003.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-2/input0 [ 2.352007] raid6: mmxx2 2689 MB/s [ 2.420006] raid6: sse1x1 1666 MB/s [ 2.488015] raid6: sse1x2 2093 MB/s [ 2.556000] raid6: sse2x1 3150 MB/s [ 2.624000] raid6: sse2x2 4083 MB/s [ 2.624002] raid6: using algorithm sse2x2 (4083 MB/s) [ 2.629316] md: raid6 personality registered for level 6 [ 2.629319] md: raid5 personality registered for level 5 [ 2.629321] md: raid4 personality registered for level 4 [ 2.645786] md: md0 stopped. [ 2.647341] md: bind<sdb1> [ 2.647486] md: bind<sdc1> [ 2.647622] md: bind<sda1> [ 2.650732] raid1: raid set md0 active with 3 out of 3 mirrors [ 2.650762] md0: detected capacity change from 0 to 254791680 [ 2.651683] md0: unknown partition table [ 2.862783] md: md1 stopped. [ 2.865116] md: bind<sdb2> [ 2.865306] md: bind<sdc2> [ 2.887252] md: bind<sda2> [ 2.888656] raid5: device sda2 operational as raid disk 0 [ 2.888659] raid5: device sdc2 operational as raid disk 2 [ 2.888662] raid5: device sdb2 operational as raid disk 1 [ 2.889011] raid5: allocated 3179kB for md1 [ 2.889051] 0: w=1 pa=0 pr=3 m=1 a=2 r=3 op1=0 op2=0 [ 2.889055] 2: w=2 pa=0 pr=3 m=1 a=2 r=3 op1=0 op2=0 [ 2.889058] 1: w=3 pa=0 pr=3 m=1 a=2 r=3 op1=0 op2=0 [ 2.889060] raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2 [ 2.889062] RAID5 conf printout: [ 2.889064] --- rd:3 wd:3 [ 2.889066] disk 0, o:1, dev:sda2 [ 2.889068] disk 1, o:1, dev:sdb2 [ 2.889071] disk 2, o:1, dev:sdc2 [ 2.889104] md1: detected capacity change from 0 to 39995834368 [ 2.889915] md1: unknown partition table [ 3.100482] device-mapper: uevent: version 1.0.3 [ 3.100614] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected] [ 24.263278] kjournald starting. Commit interval 5 seconds [ 24.263292] EXT3-fs: mounted filesystem with ordered data mode. [ 25.227397] udev[441]: starting version 164 [ 25.521819] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 [ 25.521828] ACPI: Power Button [PWRB] [ 25.521924] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 25.521928] ACPI: Power Button [PWRF] [ 25.526370] ACPI: SSDT 1ff9e0b0 001C6 (v01 AMI CPU1PM 00000001 INTL 20060113) [ 25.526902] processor LNXCPU:00: registered as cooling_device0 [ 25.527253] ACPI: SSDT 1ff9e280 0013A (v01 AMI CPU2PM 00000001 INTL 20060113) [ 25.528316] processor LNXCPU:01: registered as cooling_device1 [ 25.573243] parport_pc 00:06: reported by Plug and Play ACPI [ 25.573351] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 25.593992] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 25.893039] intel_rng: FWH not detected [ 25.953750] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 23 (level, low) -> IRQ 23 [ 25.953757] ACPI: I/O resource 0000:00:1f.3 [0x400-0x41f] conflicts with ACPI region SMRG [0x400-0x40f] [ 25.953796] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 26.097600] [drm] Initialized drm 1.1.0 20060810 [ 26.115882] Error: Driver 'pcspkr' is already registered, aborting... [ 26.220939] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 26.220972] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 26.288187] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 26.288196] pci 0000:04:00.0: setting latency timer to 64 [ 26.291474] [drm] nouveau 0000:04:00.0: Detected an NV40 generation card (0x04b200a2) [ 26.291956] [drm] Initialized nouveau 0.0.15 20090420 for 0000:04:00.0 on minor 0 [ 26.386314] hda_codec: ALC882: BIOS auto-probing. [ 26.387640] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5 [ 26.983643] EXT3 FS on dm-0, internal journal [ 27.268969] loop: module loaded [ 27.734845] kjournald starting. Commit interval 5 seconds [ 27.746043] EXT3 FS on md0, internal journal [ 27.746049] EXT3-fs: mounted filesystem with ordered data mode. [ 28.309536] sky2 eth0: enabling interface [ 28.309581] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 31.002847] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 31.002895] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.548021] eth0: no IPv6 routers present [ 94.085511] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [ 94.086643] SGI XFS Quota Management subsystem [ 94.108312] JFS: nTxBlock = 4016, nTxLock = 32129 [ 94.155909] NTFS driver 2.1.29 [Flags: R/W MODULE]. [ 94.228150] QNX4 filesystem 0.2.3 registered. [ 94.342676] Btrfs loaded [ 432.432050] usb 3-2: USB disconnect, address 3 [ 438.632037] usb 3-1: USB disconnect, address 2 [ 447.248028] usb 3-2: new low speed USB device using uhci_hcd and address 4 [ 447.423031] usb 3-2: New USB device found, idVendor=413c, idProduct=2003 [ 447.423036] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 447.423039] usb 3-2: Product: Dell USB Keyboard [ 447.423041] usb 3-2: Manufacturer: Dell [ 447.423123] usb 3-2: configuration #1 chosen from 1 choice [ 447.457377] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input6 [ 447.457500] generic-usb 0003:413C:2003.0003: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-2/input0 [ 449.296046] usb 3-2: USB disconnect, address 4 ** Model information not available ** Loaded modules: Module Size Used by btrfs 366994 0 zlib_deflate 15822 1 btrfs crc32c 2172 1 libcrc32c 762 1 btrfs ufs 56158 0 qnx4 5118 0 hfsplus 61005 0 hfs 33093 0 minix 17814 0 ntfs 163917 0 vfat 6570 0 msdos 5118 0 fat 34912 2 vfat,msdos jfs 134612 0 xfs 415605 0 exportfs 2618 1 xfs reiserfs 176190 0 ext4 256872 0 jbd2 56155 1 ext4 crc16 1027 1 ext4 ext2 46245 0 loop 9769 0 snd_hda_codec_realtek 163318 1 nouveau 314892 0 snd_hda_intel 16823 0 ttm 33502 1 nouveau snd_hda_codec 46002 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 4054 1 snd_hda_codec drm_kms_helper 18569 1 nouveau drm 111992 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 3497 1 nouveau i2c_i801 6462 0 snd_pcm 47226 2 snd_hda_intel,snd_hda_codec snd_timer 12270 1 snd_pcm rng_core 2178 0 psmouse 44809 0 i2c_core 12787 5 nouveau,drm_kms_helper,drm,i2c_algo_bit,i2c_i801 snd 34423 6 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer soundcore 3450 1 snd asus_atk0110 6770 0 snd_page_alloc 5045 2 snd_hda_intel,snd_pcm serio_raw 2916 0 pcspkr 1207 0 evdev 5609 2 parport_pc 15799 0 parport 22554 1 parport_pc processor 26327 0 button 3598 1 nouveau ext3 94396 2 jbd 32317 1 ext3 mbcache 3762 3 ext4,ext2,ext3 sha256_generic 10748 2 aes_i586 6816 2 aes_generic 25738 1 aes_i586 cbc 2047 1 dm_crypt 9264 1 dm_mod 46234 3 dm_crypt raid456 42884 1 async_raid6_recov 4130 1 raid456 async_pq 2643 2 raid456,async_raid6_recov raid6_pq 77468 2 async_raid6_recov,async_pq async_xor 1954 3 raid456,async_raid6_recov,async_pq xor 12418 1 async_xor async_memcpy 838 2 raid456,async_raid6_recov async_tx 1326 5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy raid1 16375 1 md_mod 67385 4 raid456,raid1 usbhid 28008 0 hid 50909 1 usbhid sg 19937 0 sr_mod 10770 0 cdrom 26487 1 sr_mod sd_mod 26005 9 crc_t10dif 1012 1 sd_mod ata_generic 2247 0 ata_piix 17736 0 pata_it821x 6610 6 uhci_hcd 16057 0 ahci 27410 0 thermal 9206 0 thermal_sys 9378 2 processor,thermal sky2 34040 0 ehci_hcd 28693 0 libata 115869 4 ata_generic,ata_piix,pata_it821x,ahci scsi_mod 104853 4 sg,sr_mod,sd_mod,libata usbcore 98969 4 usbhid,uhci_hcd,ehci_hcd nls_base 4541 7 hfsplus,hfs,ntfs,vfat,fat,jfs,usbcore ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp post-up /sbin/ethtool -s $IFACE wol g post-down /sbin/ethtool -s $IFACE wol g ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:17:31:8d:80:06 brd ff:ff:ff:ff:ff:ff inet 192.168.2.6/24 brd 192.168.2.255 scope global eth0 inet6 fe80::217:31ff:fe8d:8006/64 scope link valid_lft forever preferred_lft forever *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 560 8 0 0 0 0 0 0 560 8 0 0 0 0 0 0 eth0:103673667 94057 0 0 0 0 0 0 5576213 62763 0 0 0 0 0 0 *** Protocol statistics: Ip: 94040 total packets received 2 with invalid addresses 0 forwarded 0 incoming packets discarded 94038 incoming packets delivered 62740 requests sent out Icmp: 0 ICMP messages received 0 input ICMP message failed. ICMP input histogram: 0 ICMP messages sent 0 ICMP messages failed ICMP output histogram: Tcp: 3 active connections openings 7 passive connection openings 0 failed connection attempts 4 connection resets received 2 connections established 93648 segments received 62691 segments send out 13 segments retransmited 0 bad segments received. 4 resets sent Udp: 36 packets received 0 packets to unknown port received. 0 packet receive errors 36 packets sent UdpLite: TcpExt: 1 packets pruned from receive queue because of socket buffer overrun 2 TCP sockets finished time wait in fast timer 68 delayed acks sent Quick ack mode was activated 164 times 7 packets directly queued to recvmsg prequeue. 7 bytes directly received in process context from prequeue 76824 packet headers predicted 1334 acknowledgments not containing data payload received 8492 predicted acknowledgments 2 times recovered from packet loss by selective acknowledgements 1 timeouts after SACK recovery 3 fast retransmits 3 forward retransmits 6 other TCP timeouts 441 packets collapsed in receive queue due to low socket buffer 274 DSACKs sent for old packets TCPSackMerged: 5 TCPSackShiftFallback: 35 IpExt: InMcastPkts: 36 InBcastPkts: 318 InOctets: 102356279 OutOctets: 4696407 InMcastOctets: 1296 InBcastOctets: 25758 ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02) Subsystem: Intel Corporation Device [8086:2580] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:01.0 PCI bridge [0604]: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port [8086:2771] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 16 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: cdf00000-cfffffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01) Subsystem: ASUSTeK Computer Inc. Device [1043:8237] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 16 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at cdcf8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: HDA Intel 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 16 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: 20000000-201fffff Prefetchable memory behind bridge: 0000000020200000-00000000203fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 16 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: cde00000-cdefffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at 7000 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at 7400 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 7800 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at 8000 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at cdcff800 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000a000-0000bfff Memory behind bridge: cdd00000-cddfffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at ffa0 [size=16] Kernel driver in use: ata_piix 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA AHCI Controller [8086:27c1] (rev 01) (prog-if 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. Device [1043:2606] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 28 Region 0: I/O ports at 9800 [size=8] Region 1: I/O ports at 9400 [size=4] Region 2: I/O ports at 9000 [size=8] Region 3: I/O ports at 8800 [size=4] Region 4: I/O ports at 8400 [size=16] Region 5: Memory at cdcffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 23 Region 4: I/O ports at 0400 [size=32] 01:03.0 Mass storage controller [0180]: Integrated Technology Express, Inc. ITE 8211F Single Channel UDMA 133 [1283:8211] (rev 11) Subsystem: ASUSTeK Computer Inc. P5GD1-VW Mainboard [1043:8138] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min, 2000ns max) Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at b800 [size=8] Region 1: I/O ports at b400 [size=4] Region 2: I/O ports at b000 [size=8] Region 3: I/O ports at a800 [size=4] Region 4: I/O ports at a400 [size=16] Expansion ROM at cdde0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: pata_it821x 02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller [11ab:4362] (rev 19) Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet controller PCIe (Asus) [1043:8142] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 16 bytes Interrupt: pin A routed to IRQ 27 Region 0: Memory at cdefc000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at c800 [size=256] Expansion ROM at cdec0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: sky2 04:00.0 VGA compatible controller [0300]: nVidia Corporation G73 [GeForce 7600 GS] [10de:0392] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device [1043:81f6] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 16 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at cf000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at ce000000 (64-bit, non-prefetchable) [size=16M] Region 5: I/O ports at e800 [size=128] Expansion ROM at cdfe0000 [disabled] [size=128K] Capabilities: <access denied> ** USB devices: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 6.0.3 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/2 CPU cores) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-686 depends on: ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs ii linux-base 2.6.32-38 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-686 recommends: pn firmware-linux-free <none> (no description available) ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib Versions of packages linux-image-2.6.32-5-686 suggests: pn grub | lilo <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686: linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686: -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
