Package: src:linux Version: 3.8.11-1 Severity: important I have two disks, one SSD and one HDD. There are to MD RAID1 volumes that each use one partition on the SSD and one on the HDD.
After the first reboot with 3.8, MD kicked the HDD's partitions from both RAID devices. However, there were no actual errors logged in kern.log, the other (non-RAID partitions) on the HDD continued to work fine and SMART did not report any error: May 8 20:32:18 k kernel: [ 16.967657] md/raid1:md1: Disk failure on sdb9, disabling device. May 8 20:32:18 k kernel: [ 16.967657] md/raid1:md1: Operation continuing on 1 devices. May 8 20:32:18 k kernel: [ 17.172624] RAID1 conf printout: May 8 20:32:18 k kernel: [ 17.172629] --- wd:1 rd:2 May 8 20:32:18 k kernel: [ 17.172633] disk 0, wo:0, o:1, dev:sda6 May 8 20:32:18 k kernel: [ 17.172637] disk 1, wo:1, o:0, dev:sdb9 May 8 20:32:18 k kernel: [ 17.172791] RAID1 conf printout: May 8 20:32:18 k kernel: [ 17.172796] --- wd:1 rd:2 May 8 20:32:18 k kernel: [ 17.172801] disk 0, wo:0, o:1, dev:sda6 ... May 8 20:33:33 k kernel: [ 94.707222] md/raid1:md0: Disk failure on sdb7, disabling device. May 8 20:33:33 k kernel: [ 94.707222] md/raid1:md0: Operation continuing on 1 devices. May 8 20:33:33 k kernel: [ 94.709046] RAID1 conf printout: May 8 20:33:33 k kernel: [ 94.709051] --- wd:1 rd:2 May 8 20:33:33 k kernel: [ 94.709056] disk 0, wo:0, o:1, dev:sda1 May 8 20:33:33 k kernel: [ 94.709059] disk 1, wo:1, o:0, dev:sdb7 May 8 20:33:33 k kernel: [ 94.712138] RAID1 conf printout: May 8 20:33:33 k kernel: [ 94.712141] --- wd:1 rd:2 May 8 20:33:33 k kernel: [ 94.712144] disk 0, wo:0, o:1, dev:sda1 Re-adding the devices resulted in immediate RAID failures again (see below for the log). As there was no change with mdadm, I guess this is a kernel bug. Initially, the partitions on the HDD were marked as write-mostly with mdadm. However, when re-adding the partitions, I did not specify --write-mostly again, which (if I read mdadm's man page right) should have lead to write-mostly not being active. -- Package-specific info: ** Version: Linux version 3.8-1-amd64 ([email protected]) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Debian 3.8.11-1 ** Command line: BOOT_IMAGE=/boot/vmlinuz-3.8-1-amd64 root=UUID=16fd1e3f-26b7-41ce-b31d-ac1a9e7e9150 ro rootfstype=ext4 mtrr_spare_reg_num=3 enable_mtrr_cleanup ** Tainted: PO (4097) * Proprietary module has been loaded. * Out-of-tree module has been loaded. ** Kernel log: [ 4.198739] input: HDA Intel MID Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16 [ 4.199874] hda_intel: Disabling MSI [ 4.199929] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client [ 5.005082] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input17 [ 5.005451] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input18 [ 5.005814] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input19 [ 5.006181] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input20 [ 5.325678] EXT4-fs (md0): re-mounted. Opts: (null) [ 5.412252] EXT4-fs (md0): re-mounted. Opts: acl [ 5.919334] fuse init (API version 7.20) [ 5.979129] Bridge firewalling registered [ 5.998981] it87: Found IT8720F chip at 0x290, revision 8 [ 5.999049] it87: VID is disabled (pins used for GPIO) [ 5.999116] it87: Routing internal VCCH to in7 [ 5.999175] it87: Beeping is supported [ 6.251326] bio: create slab <bio-1> at 1 [ 7.830383] Adding 1572860k swap on /dev/mapper/vg0-swap. Priority:-1 extents:1 across:1572860k [ 9.605659] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: acl [ 9.662089] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: acl [ 9.684424] REISERFS (device dm-2): found reiserfs format "3.6" with standard journal [ 9.684514] REISERFS (device dm-2): using ordered data mode [ 9.684568] reiserfs: using flush barriers [ 9.694345] REISERFS (device dm-2): journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 9.694730] REISERFS (device dm-2): checking transaction log (dm-2) [ 9.808607] REISERFS (device dm-2): Using r5 hash to sort names [ 9.878067] EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null) [ 9.909102] EXT4-fs (dm-3): barriers disabled [ 9.912596] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: nobarrier [ 9.927252] EXT4-fs (dm-4): barriers disabled [ 9.939415] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: nobarrier [ 9.957582] EXT4-fs (dm-7): barriers disabled [ 9.959628] EXT4-fs (dm-7): mounted filesystem with writeback data mode. Opts: nobarrier,data=writeback [ 10.340381] r8169 0000:03:00.0: firmware: agent loaded rtl_nic/rtl8168d-2.fw into memory [ 10.398755] r8169 0000:03:00.0 eth0: link down [ 10.398784] r8169 0000:03:00.0 eth0: link down [ 10.398888] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.750361] r8169 0000:03:00.0 eth0: link up [ 12.750428] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 15.766336] RPC: Registered named UNIX socket transport module. [ 15.766414] RPC: Registered udp transport module. [ 15.766472] RPC: Registered tcp transport module. [ 15.766530] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 15.771825] FS-Cache: Loaded [ 15.772635] Key type dns_resolver registered [ 15.781818] FS-Cache: Netfs 'nfs' registered for caching [ 15.791496] Installing knfsd (copyright (C) 1996 [email protected]). [ 16.720402] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 16.732925] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.807146] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 16.807760] NFSD: starting 90-second grace period (net ffffffff8166a140) [ 17.724031] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input21 [ 18.357619] lp: driver loaded but no devices found [ 18.366478] ppdev: user-space parallel port driver [ 18.572673] Ebtables v2.0 registered [ 18.579948] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2398.365988] md: export_rdev(sdb7) [ 2398.427750] md: bind<sdb7> [ 2398.436557] RAID1 conf printout: [ 2398.436563] --- wd:1 rd:2 [ 2398.436568] disk 0, wo:0, o:1, dev:sda1 [ 2398.436573] disk 1, wo:1, o:1, dev:sdb7 [ 2398.436691] md: recovery of RAID array md0 [ 2398.436700] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 2398.436707] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [ 2398.436714] md: using 128k window, over a total of 18877368k. [ 2435.557535] md: export_rdev(sdb9) [ 2435.888079] md: bind<sdb9> [ 2435.895533] RAID1 conf printout: [ 2435.895538] --- wd:1 rd:2 [ 2435.895543] disk 0, wo:0, o:1, dev:sda6 [ 2435.895546] disk 1, wo:1, o:1, dev:sdb9 [ 2435.895873] md: delaying recovery of md1 until md0 has finished (they share one or more physical units) [ 2581.268514] md: md0: recovery done. [ 2581.286223] md: recovery of RAID array md1 [ 2581.286229] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 2581.286232] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [ 2581.286237] md: using 128k window, over a total of 31455160k. [ 2581.412775] RAID1 conf printout: [ 2581.412782] --- wd:2 rd:2 [ 2581.412788] disk 0, wo:0, o:1, dev:sda1 [ 2581.412792] disk 1, wo:0, o:1, dev:sdb7 [ 3187.131788] md/raid1:md0: Disk failure on sdb7, disabling device. [ 3187.131788] md/raid1:md0: Operation continuing on 1 devices. [ 3187.133622] RAID1 conf printout: [ 3187.133627] --- wd:1 rd:2 [ 3187.133631] disk 0, wo:0, o:1, dev:sda1 [ 3187.133635] disk 1, wo:1, o:0, dev:sdb7 [ 3187.136262] RAID1 conf printout: [ 3187.136270] --- wd:1 rd:2 [ 3187.136278] disk 0, wo:0, o:1, dev:sda1 [ 3187.483311] md/raid1:md1: Disk failure on sdb9, disabling device. [ 3187.483311] md/raid1:md1: Operation continuing on 1 devices. [ 3188.232419] md: md1: recovery done. [ 3188.236850] RAID1 conf printout: [ 3188.236855] --- wd:1 rd:2 [ 3188.236860] disk 0, wo:0, o:1, dev:sda6 [ 3188.236863] disk 1, wo:1, o:0, dev:sdb9 [ 3188.236923] RAID1 conf printout: [ 3188.236927] --- wd:1 rd:2 [ 3188.236931] disk 0, wo:0, o:1, dev:sda6 ** Model information sys_vendor: Gigabyte Technology Co., Ltd. product_name: P55-UD3 product_version: chassis_vendor: Gigabyte Technology Co., Ltd. chassis_version: bios_vendor: Award Software International, Inc. bios_version: F9 board_vendor: Gigabyte Technology Co., Ltd. board_name: P55-UD3 board_version: x.x ** Loaded modules: ip6table_filter ip6_tables ebtable_nat ebtables parport_pc ppdev lp parport xt_tcpudp xt_conntrack iptable_nat nf_nat_ipv4 nf_nat iptable_filter ip_tables x_tables binfmt_misc nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack uinput nfsd auth_rpcgss nfs_acl nfs lockd dns_resolver fscache sunrpc reiserfs dm_crypt it87 hwmon_vid bridge stp llc fuse snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel nvidia(PO) snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_page_alloc snd_seq_midi snd_seq_midi_event synaptics_usb snd_rawmidi snd_seq coretemp kvm_intel iTCO_wdt kvm iTCO_vendor_support snd_seq_device snd_timer crc32c_intel snd pcspkr evdev soundcore lpc_ich i7core_edac i2c_i801 mfd_core edac_core i2c_core acpi_cpufreq mperf processor button thermal_sys ext4 crc16 jbd2 mbcache btrfs zlib_deflate crc32c libcrc32c dm_mod raid1 md_mod sr_mod cdrom ata_generic hid_generic usbhid hid sg sd_mod crc_t10dif usb_storage microcode ahci r8169 ehci_pci libahci pata_jmicron mii libata uhci_hcd ehci_hcd scsi_mod usbcore usb_common ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Core Processor DMI [8086:d131] (rev 11) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:03.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express Root Port 1 [8086:d138] (rev 11) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: f9000000-faffffff Prefetchable memory behind bridge: 00000000d0000000-00000000efffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:08.0 System peripheral [0880]: Intel Corporation Core Processor System Management Registers [8086:d155] (rev 11) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:08.1 System peripheral [0880]: Intel Corporation Core Processor Semaphore and Scratchpad Registers [8086:d156] (rev 11) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:08.2 System peripheral [0880]: Intel Corporation Core Processor System Control and Status Registers [8086:d157] (rev 11) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:08.3 System peripheral [0880]: Intel Corporation Core Processor Miscellaneous Registers [8086:d158] (rev 11) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:10.0 System peripheral [0880]: Intel Corporation Core Processor QPI Link [8086:d150] (rev 11) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:10.1 System peripheral [0880]: Intel Corporation Core Processor QPI Routing and Protocol Registers [8086:d151] (rev 11) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b3b] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at ff00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.1 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b3e] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at fe00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.2 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b3f] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at fd00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.7 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio [8086:3b56] (rev 05) Subsystem: Giga-byte Technology Device [1458:a002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 47 Region 0: Memory at fbff8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fbe00000-fbefffff Prefetchable memory behind bridge: 00000000cf800000-00000000cf9fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 [8086:3b44] (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fbd00000-fbdfffff Prefetchable memory behind bridge: 00000000fbc00000-00000000fbcfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b36] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at fc00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b37] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at fb00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b38] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at fa00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b39] (rev 05) (prog-if 00 [UHCI]) Subsystem: Giga-byte Technology Device [1458:5004] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at f900 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 5 Series Chipset LPC Interface Controller [8086:3b02] (rev 05) Subsystem: Giga-byte Technology Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b22] (rev 05) (prog-if 01 [AHCI 1.0]) Subsystem: Giga-byte Technology Device [1458:b005] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 46 Region 0: I/O ports at f800 [size=8] Region 1: I/O ports at f700 [size=4] Region 2: I/O ports at f600 [size=8] Region 3: I/O ports at f500 [size=4] Region 4: I/O ports at f400 [size=32] Region 5: Memory at fbffd000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 05) Subsystem: Giga-byte Technology Device [1458:5001] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0500 [size=32] Kernel driver in use: i801_smbus 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT218 [GeForce 210] [10de:0a65] (rev a2) (prog-if 00 [VGA controller]) Subsystem: CardExpert Technology Device [10b0:1401] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at ee000000 (64-bit, prefetchable) [size=32M] Region 5: I/O ports at cf00 [size=128] [virtual] Expansion ROM at e0000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia 01:00.1 Audio device [0403]: NVIDIA Corporation High Definition Audio Controller [10de:0be3] (rev a1) Subsystem: CardExpert Technology Device [10b0:1401] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at faffc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 02:00.0 SATA controller [0106]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 5: Memory at fbefe000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: ahci 02:00.1 IDE interface [0101]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO]) Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at ef00 [size=8] Region 1: I/O ports at ee00 [size=4] Region 2: I/O ports at ed00 [size=8] Region 3: I/O ports at ec00 [size=4] Region 4: I/O ports at eb00 [size=16] Capabilities: <access denied> Kernel driver in use: pata_jmicron 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) Subsystem: Giga-byte Technology GA-EP45-DS5/GA-EG45M-DS2H Motherboard [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: I/O ports at de00 [size=256] Region 2: Memory at fbcff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fbcf8000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at fbc00000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: r8169 3f:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers [8086:2c51] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture System Address Decoder [8086:2c81] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0 [8086:2c90] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel driver in use: i7core_edac 3f:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0 [8086:2c91] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller [8086:2c98] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder [8086:2c99] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:03.4 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Test Registers [8086:2c9c] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers [8086:2ca0] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers [8086:2ca1] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.2 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers [8086:2ca2] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:04.3 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers [8086:2ca3] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers [8086:2ca8] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers [8086:2ca9] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.2 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers [8086:2caa] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:05.3 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers [8086:2cab] (rev 04) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 -- System Information: Debian Release: jessie/sid APT prefers unstable APT policy: (500, 'unstable'), (500, 'stable'), (1, 'experimental') Architecture: i386 (x86_64) Kernel: Linux 3.8-1-amd64 (SMP w/8 CPU cores) Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.8-1-amd64 depends on: ii debconf [debconf-2.0] 1.5.50 ii initramfs-tools [linux-initramfs-tool] 0.112 ii kmod 9-3 ii linux-base 3.5 ii module-init-tools 9-3 Versions of packages linux-image-3.8-1-amd64 recommends: ii firmware-linux-free 3.2 ii libc6-i686 2.17-1 Versions of packages linux-image-3.8-1-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-27.1 pn linux-doc-3.8 <none> Versions of packages linux-image-3.8-1-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> ii firmware-linux 0.38 ii firmware-linux-nonfree 0.38 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> ii firmware-realtek 0.38 pn xen-hypervisor <none> -- debconf information: linux-image-3.8-1-amd64/postinst/missing-firmware-3.8-1-amd64: linux-image-3.8-1-amd64/prerm/removing-running-kernel-3.8-1-amd64: true linux-image-3.8-1-amd64/postinst/ignoring-ramdisk: linux-image-3.8-1-amd64/postinst/depmod-error-initrd-3.8-1-amd64: false -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
