Package: src:linux Version: 3.2.41-2+deb7u2 Severity: normal soekris lan1741 4port pci via-rhine card does not initialise correctly. MAC addresses are not found. Sometimes one mac address is correctly found and then that port will work.
-- Package-specific info: ** Version: Linux version 3.2.0-4-amd64 ([email protected]) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.41-2+deb7u2 ** Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=f01a829b-4553-4361-a6b8-106f09426ea5 ro quiet ** Tainted: W (512) * Taint on warning. ** Kernel log: [ 129.749426] eth2: no IPv6 routers present [ 138.851897] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 138.853045] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 138.853186] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 138.859112] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 138.859223] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 138.865097] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 154.819250] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 154.819450] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 154.825809] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 172.782328] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 172.783554] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 172.784770] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 172.784962] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 172.791212] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 172.791385] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 172.797661] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 172.797865] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 172.804141] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 176.774129] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 176.775377] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 176.776609] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 176.776730] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 176.783022] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 176.783139] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 176.789382] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 176.789503] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 176.795908] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 178.329704] eth0: no IPv6 routers present [ 178.736876] eth1: no IPv6 routers present [ 178.768825] eth2: no IPv6 routers present [ 206.712701] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 206.712811] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 206.719115] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 208.708607] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 208.708724] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 208.714998] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 426.261917] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 426.262037] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 426.268036] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 518.073472] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 518.074602] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 518.075729] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 518.075850] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 518.081672] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 518.081790] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 518.087573] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 518.087735] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 518.093533] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 522.065270] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 522.066399] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 522.067527] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 522.067645] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 522.073459] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 522.073568] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 522.079588] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 522.079749] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 522.085554] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 523.405393] eth1: no IPv6 routers present [ 523.549090] eth2: no IPv6 routers present [ 523.932307] eth0: no IPv6 routers present [ 548.012014] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 548.012138] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 548.017928] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 550.007917] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 550.008041] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 550.013827] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 565.975140] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 565.975269] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 565.981052] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 567.971046] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 567.972175] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 567.972286] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 567.978090] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 567.978200] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 567.983975] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 569.966962] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 569.967089] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 569.972866] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 571.962858] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 571.964054] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 571.964253] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 571.970189] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 571.970309] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 571.976079] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 572.328971] eth1: no IPv6 routers present [ 572.728146] eth0: no IPv6 routers present [ 572.919757] eth2: no IPv6 routers present [ 573.958751] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 573.958878] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 573.964661] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 613.876823] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting... [ 613.877961] via-rhine 0000:03:02.0: eth2: Transmit timed out, status ffff, PHY status ffff, resetting... [ 613.878069] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder. [ 613.884110] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 613.884260] via-rhine 0000:03:02.0: eth2: Reset not complete yet. Trying harder. [ 613.890361] via-rhine 0000:03:02.0: eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF [ 615.872815] via-rhine 0000:03:00.0: eth0: Transmit timed out, status ffff, PHY status ffff, resetting... [ 615.872989] via-rhine 0000:03:00.0: eth0: Reset not complete yet. Trying harder. [ 615.879085] via-rhine 0000:03:00.0: eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF ** Model information sys_vendor: product_name: product_version: chassis_vendor: chassis_version: bios_vendor: Intel Corp. bios_version: MUCDT10N.86A.0075.2013.0427.1548 board_vendor: Intel Corporation board_name: D2700DC board_version: AAG32420-602 ** Loaded modules: parport_pc ppdev lp parport bnep rfcomm bluetooth rfkill binfmt_misc nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc loop gma500_gfx snd_hda_codec_realtek drm_kms_helper snd_hda_codec_hdmi drm i2c_i801 i2c_algo_bit iTCO_wdt i2c_core iTCO_vendor_support pcspkr snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_page_alloc evdev psmouse serio_raw snd_seq snd_seq_device snd_timer coretemp snd shpchp soundcore video processor button thermal_sys ext4 crc16 jbd2 mbcache sg sd_mod crc_t10dif usbhid hid usb_storage via_rhine mii ahci libahci uhci_hcd libata scsi_mod ehci_hcd e1000e usbcore usb_common ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controller [8086:0bf3] (rev 03) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller [8086:0be2] (rev 09) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 46 Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=1M] Region 1: I/O ports at 30d0 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: gma500 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Intel Corporation Device [8086:2011] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at 80400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 80100000-801fffff Prefetchable memory behind bridge: 0000000080500000-00000000806fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at 30a0 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 3080 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 3060 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at 3040 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at 80304400 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=03, sec-latency=32 I/O behind bridge: 00001000-00001fff Memory behind bridge: 80000000-800fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 44 Region 0: I/O ports at 30c8 [size=8] Region 1: I/O ports at 30dc [size=4] Region 2: I/O ports at 30c0 [size=8] Region 3: I/O ports at 30d8 [size=4] Region 4: I/O ports at 3020 [size=16] Region 5: Memory at 80304000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 3000 [size=32] Kernel driver in use: i801_smbus 01:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] Subsystem: Intel Corporation Device [8086:2011] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at 80120000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at 80100000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Region 3: Memory at 80140000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e 02:00.0 PCI bridge [0604]: Texas Instruments PCI2250 PCI-to-PCI Bridge [104c:ac23] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Bus: primary=02, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: 80000000-800fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 03:00.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96) Subsystem: VIA Technologies, Inc. Device [1106:0106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at 1300 [size=256] Region 1: Memory at 80000300 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine 03:01.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96) Subsystem: VIA Technologies, Inc. Device [1106:0106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at 1200 [size=256] Region 1: Memory at 80000200 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine 03:02.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96) Subsystem: VIA Technologies, Inc. Device [1106:0106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 1100 [size=256] Region 1: Memory at 80000100 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine 03:03.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105M [Rhine-III] [1106:3053] (rev 96) Subsystem: VIA Technologies, Inc. Device [1106:0106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at 1000 [size=256] Region 1: Memory at 80000000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine ** USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 152d:2338 JMicron Technology Corp. / JMicron USA Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge Bus 003 Device 002: ID 046d:c019 Logitech, Inc. Optical Tilt Wheel Mouse Bus 004 Device 002: ID 046d:c315 Logitech, Inc. Classic New Touch Keyboard -- System Information: Debian Release: 7.0 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores) Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.2.0-4-amd64 depends on: ii debconf [debconf-2.0] 1.5.49 ii initramfs-tools [linux-initramfs-tool] 0.109.1 ii kmod 9-3 ii linux-base 3.5 ii module-init-tools 9-3 Versions of packages linux-image-3.2.0-4-amd64 recommends: pn firmware-linux-free <none> Versions of packages linux-image-3.2.0-4-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-27+deb7u1 pn linux-doc-3.2 <none> Versions of packages linux-image-3.2.0-4-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk: linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64: -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
