When booted using the options that produced the dmesg output that you sent, what is the output of the following commands?
cdrecord -scanbus cdrecord dev=ATAPI: -scanbus cdrecord dev=ATA: -scanbus Robert On Wed, 2006-02-08 at 22:15 -0700, Stefan Srdic wrote: > hi, I've recently installed Etch on my Toshiba Satallite M40. The > installation was a little rough, I had to manipulate the modules in > expert mode in order for the installation to detect my DVD drive and > complete the installation. > > Since the installation I've had to compile a new kernel along with a few > patches in order to get my network card and MMC/SD controller to > function. So far everything works except for my DVD drive. > > >From what I've read on the net, libata.h needs to be edited in order to > support ATAPI. I've tried to define a thing or two in libata.h with no > success: > > #undef ATA_ENABLE_PATA /* define to enable PATA support in some > * low-level drivers */ > #undef ATAPI_ENABLE_DMADIR /* enables ATAPI DMADIR bridge support */ > > Changed to: > > #define ATA_ENABLE_PATA /* define to enable PATA support in some > * low-level drivers */ > #define ATAPI_ENABLE_DMADIR /* enables ATAPI DMADIR bridge support */ > > > > I've even tried to pass the arguments libata.atapi_enable=1 and > atapi_enable=1 to the kernel through lilo with no success. So far, the > best that I could manage was this: > libata version 1.20 loaded. > ata_piix 0000:00:1f.2: version 1.05 > ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 > ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 11 (level, > low) -> IRQ 11 > PCI: Setting latency timer of device 0000:00:1f.2 to 64 > ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1100 irq 14 > ata1: dev 0 cfg 49:2f00 82:746b 83:7d09 84:6023 85:7468 86:3c09 87:6023 > 88:203f > ata1: dev 0 ATA-6, max UDMA/100, 195371568 sectors: LBA48 > ata1(0): applying bridge limits > ata1: dev 0 configured for UDMA/100 > scsi0 : ata_piix > Vendor: ATA Model: TOSHIBA MK1031GA Rev: AA20 > Type: Direct-Access ANSI SCSI revision: 05 > ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15 > ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 > 88:0407 > ata2: dev 0 ATAPI, max UDMA/33 > ata2(0): applying bridge limits > ata2: dev 0 configured for UDMA/33 > scsi1 : ata_piix > ata2(0): WARNING: ATAPI is disabled, device ignored. > SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB) > SCSI device sda: drive cache: write back > SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB) > SCSI device sda: drive cache: write back > sda: sda1 sda2 < sda5 > > sd 0:0:0:0: Attached scsi disk sda > sd 0:0:0:0: Attached scsi generic sg0 type 0 > > Can sombody please help me enable ATAPI devices under libata, I've only > found outdated documentation that is irrelavent for my kernel version. > > Thanks > > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
