On Tue, 2002-07-09 at 10:19, Corsini Egidio wrote: > ... and the driver should be r128
No, it shouldn't, see below. > I'm trying to setup X on my PowerBook G3. When on the 2.2 kernel > installed by Debian, I manage to launch X using "fbdev" device (but not > "ati"). When switching to a 2.4.19 kernel though, even that does not > work. I have sifted through this mailing list, tried various suggested > settings, but without success. Maybe you're running OFfb now instead of atyfb? > Section "Device" > Identifier "ATI" > Driver "ati" > BusID "PCI:00:17:00" > Option "UseFBDev" "true" This option has no effect with your chip, it shouldn't hurt though. > EndSection > (--) PCI: (0:17:0) ATI Mach64 LI rev 220, Mem @ 0x81000000/24, > 0x80881000/12, I/O @ 0x0c00/8 Definitely not a Rage128. Driver "ati" should work with any supported ATI chip anyway. (As you can see, the bus ID in the device section is correct. lspci reports hex values) > (II) ATI(0): Not using default mode "640x350" (hsync out of range) > (II) ATI(0): Not using default mode "640x400" (hsync out of range) > (II) ATI(0): Not using default mode "720x400" (hsync out of range) > (II) ATI(0): Not using default mode "640x480" (hsync out of range) > (II) ATI(0): Not using default mode "640x480" (hsync out of range) > (II) ATI(0): Not using default mode "640x480" (hsync out of range) > (II) ATI(0): Not using default mode "640x480" (hsync out of range) > (II) ATI(0): Not using default mode "800x600" (hsync out of range) > (II) ATI(0): Not using default mode "800x600" (hsync out of range) > (II) ATI(0): Not using default mode "800x600" (hsync out of range) > (II) ATI(0): Not using default mode "800x600" (hsync out of range) > (II) ATI(0): Not using default mode "800x600" (hsync out of range) > (II) ATI(0): Not using default mode "1024x768" (hsync out of range) > (II) ATI(0): Not using default mode "1024x768" (hsync out of range) > (II) ATI(0): Not using default mode "1024x768" (hsync out of range) > (II) ATI(0): Not using default mode "1024x768" (hsync out of range) > (II) ATI(0): Not using default mode "1024x768" (hsync out of range) > (II) ATI(0): Not using default mode "1152x864" (bad mode clock/interlace/ > doublescan) > (II) ATI(0): Not using default mode "1280x960" (bad mode clock/interlace/ > doublescan) > (II) ATI(0): Not using default mode "1280x960" (bad mode clock/interlace/ > doublescan) > (II) ATI(0): Not using default mode "1280x1024" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1280x1024" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1280x1024" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1600x1200" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1600x1200" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1600x1200" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1600x1200" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1600x1200" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1792x1344" (insufficient memory for > mode) > (II) ATI(0): Not using default mode "1792x1344" (insufficient memory for > mode) > (II) ATI(0): Not using default mode "1856x1392" (insufficient memory for > mode) > (II) ATI(0): Not using default mode "1856x1392" (insufficient memory for > mode) > (II) ATI(0): Not using default mode "1920x1440" (insufficient memory for > mode) > (II) ATI(0): Not using default mode "1920x1440" (insufficient memory for > mode) > (II) ATI(0): Not using default mode "1400x1050" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using default mode "1400x1050" (bad mode clock/ > interlace/doublescan) > (II) ATI(0): Not using built-in mode "Native panel mode" (vrefresh out of > range) > (WW) ATI(0): Mode pool is empty This is the problem, looks like the ranges in the monitor section are too restrictive. -- Earthling Michel D�nzer (MrCooper)/ Debian GNU/Linux (powerpc) developer XFree86 and DRI project member / CS student, Free Software enthusiast -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
