Hi all: Give me a help. Errors happened during initial process . Here's init messages,I donnot know why it could enter into the login.Every time the process will halt at "INIT:". This is mpc850+linux2.4.4 platform
------------------------------------------------------------------ U-Boot 0.3.1 (Jul 7 2003 - 16:48:07) CPU: XPC850xxZTB at 50 MHz: 2 kB I-Cache 1 kB D-Cache ### No HW ID - assuming SVM SC8xx Watchdog enabled DRAM: 16 MB FLASH: 4 MB In: serial Out: serial Err: serial DOC: DiskOnChip 2000 @ 0x80000000, 16 MB Net: SCC ETHERNET Welcome to U-Boot SVM port Type "? or help" to get on-line help Hit any key to stop autoboot: 0 DOC read: device 0 offset 65536, size 983040 ... 983040 bytes read: OK ## Booting image at 00210000 ... Image Name: Linux-2.4.4 Created: 2003-07-07 8:51:23 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 691377 Bytes = 675.2 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.4 ([EMAIL PROTECTED]) (gcc version 2.95.3 20010111 (prerelease/fra3On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/nftla1 ip=192.21.0.61:192.21.0.81:::thunderbolt:fNR_IRQS=32 NR_SIU_INTS=16 RTL_SOFT_IRQS_FILL=16 Decrementer Frequency: 3125000 Calibrating delay loop... 49.76 BogoMIPS Memory: 14156k available (1296k kernel code, 556k data, 68k init, 0k highmem) Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 1024 (order: 1, 8192 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.8 CPM UART driver version 0.03 ttyS0 on SMC2 at 0x0380, BRG1 pty: 256 Unix98 ptys configured WDT_8xx: Software Watchdog Timer version 0.5, timeout 300 sec. Linux video capture interface: v1.00 block: queued sectors max/low 9325kB/3108kB, 64 slots per queue RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize eth0: CPM ENET Version 0.21 on SCC2, 0a:84:1a:db:d5:71 eth1: CPM ENET Version 0.21 on SCC3, 22:fa:03:5e:14:23 JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. loop: loaded (max 8 devices) SCSI subsystem driver Revision: 1.00 request_module[scsi_hostadapter]: Root fs not mounted Using configured DiskOnChip probe address 0x80000000 DiskOnChip 2000 found at address 0x80000000 Flash chip found: Manufacturer ID: EC, Chip ID: 73 (Samsung KM29U128T) 1 flash chips found. Total DiskOnChip size: 16 MiB NFTL driver: nftlcore.c $Revision: 1.83 $, nftlmount.c $Revision: 1.23 $ Cannot calculate an NFTL geometry to match size of 0x7760. Using C:1018 H:15 S:2 (== 0x774c sects) Partition check: nftla: nftla1 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 1024) IP-Config: Incomplete network configuration information. NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 68k init INIT: version 2.Welcome to Sinovee Linux 2.0 (Overlord) Press 'I' to enter interactive startup. Mounting proc filesystem: [ OK ] Configuring kernel parameters: [ OK ] Setting clock (utc): Wed Dec 31 19:39:22 EST 1969 [ OK ] Activating swap partitions: [ OK ] Setting hostname thunderbolt: [ OK ] e2fsck 1.23, 15-Aug-2001 for EXT2 FS 0.5b, 95/08/09 /dev/nftla1: clean, 743/3824 files, 14151/15279 blocks can't create lock file /etc/mtab~40: Read-only file system (use -n flag to over)/etc/rc.d/rc.sysinit: /etc/mtab: Read-only file system can't create lock file /etc/mtab~42: Read-only file system (use -n flag to over)can't create lock file /etc/mtab~43: Read-only file system (use -n flag to over)Starting watchdog: Watchdog daemon ver 0.1, (c) 2002, FEL co. ltd. [OK] touch: /var/lock/subsys/watchdog: Read-only file system INIT: /etc/rc.d/rc: /var/run/runlevel.dir: Read-only file system Starting xinetd: [ OK ] touch: /var/lock/subsys/xinetd: Read-only file system INIT: --------------------- Stop at "INIT:". Give me some help,thank you. yang [EMAIL PROTECTED] 2006-05-05