Никита <[EMAIL PROTECTED]> wrote: > >> > DEVICE partitions > >> > ARRAY /dev/md0 level=raid5 num-devices=4 > >> > UUID=bd69238b:33ed4bea:6921c83c:a87ece5a > >> > сделай так, само найдет чего ему надо.
> >> всё равно такая же ошибка.. > >> cat /etc/mdadm/mdadm.conf > >> DEVICE partitions > >> ARRAY /dev/md0 level=raid5 num-devices=4 \ > >> UUID=bd69238b:33ed4bea:6921c83c:a87ece5a > > может всетаки dmesg покажем, а не будем заниматься гаданием на кофейной > > гуще? > извиняюсь, dmesg приложил к письму [skipp] > md: linear personality registered as nr 1 > md: raid0 personality registered as nr 2 > md: raid1 personality registered as nr 3 > md: raid5 personality registered as nr 4 > raid5: automatically using best checksumming function: pIII_sse > pIII_sse : 4408.000 MB/sec > raid5: using function: pIII_sse (4408.000 MB/sec) > raid6: int32x1 808 MB/s > raid6: int32x2 871 MB/s > raid6: int32x4 636 MB/s > raid6: int32x8 531 MB/s > raid6: mmxx1 1714 MB/s > raid6: mmxx2 2000 MB/s > raid6: sse1x1 1019 MB/s > raid6: sse1x2 1093 MB/s > raid6: sse2x1 1941 MB/s > raid6: sse2x2 2121 MB/s > raid6: using algorithm sse2x2 (2121 MB/s) > md: raid6 personality registered as nr 8 > md: multipath personality registered as nr 7 > md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 > device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED] > NET: Registered protocol family 2 > IP: routing cache hash table of 8192 buckets, 64Kbytes > TCP: Hash tables configured (established 262144 bind 65536) > NET: Registered protocol family 8 > NET: Registered protocol family 20 > ACPI: (supports S0 S1 S3 S4 S5) > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. [skipp] > sata_nv version 0.02 > ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 23 (level, low) -> IRQ 177 > PCI: Setting latency timer of device 0000:00:10.0 to 64 > ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xC800 irq 177 > ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xC808 irq 177 > nv_sata: Primary device added > ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 > 88:407f > ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 > ata1: dev 0 configured for UDMA/133 > scsi0 : sata_nv > nv_sata: Secondary device added > ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 > 88:407f > ata2: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 > ata2: dev 0 configured for UDMA/133 > scsi1 : sata_nv > Vendor: ATA Model: ST3250824AS Rev: 3.AA > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) > SCSI device sda: drive cache: write back > /dev/scsi/host0/bus0/target0/lun0: p1 > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 > Vendor: ATA Model: ST3250824AS Rev: 3.AA > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) > SCSI device sdb: drive cache: write back > /dev/scsi/host1/bus0/target0/lun0: p1 > Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 > ACPI: PCI interrupt 0000:00:11.0[A] -> GSI 22 (level, low) -> IRQ 185 > PCI: Setting latency timer of device 0000:00:11.0 to 64 > ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xDC00 irq 185 > ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xDC08 irq 185 > nv_sata: Primary device added > ata3: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 > 88:407f > ata3: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 > ata3: dev 0 configured for UDMA/133 > scsi2 : sata_nv > nv_sata: Secondary device added > ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 > 88:407f > ata4: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 > ata4: dev 0 configured for UDMA/133 > scsi3 : sata_nv > Vendor: ATA Model: ST3250824AS Rev: 3.AA > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB) > SCSI device sdc: drive cache: write back > /dev/scsi/host2/bus0/target0/lun0: p1 > Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0 > Vendor: ATA Model: ST3250824AS Rev: 3.AA > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB) > SCSI device sdd: drive cache: write back > /dev/scsi/host3/bus0/target0/lun0: p1 > Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0 А теперь попробуй сам понять, как оно сможет завести массив, если дисков еще нету? Или raid в модули и грузить после sata_mv или sata_mv в ядро. Ядро в районе 2.6.8 чтоль? Больно уж sata_nv древний. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
