Вроде все распознает теперь: # dmesg | tail [ 53.819036] mtrr: base(0x92000000) is not aligned on a size(0x5000000) boundary [ 53.819854] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. [ 53.819891] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode [ 53.819954] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode [ 66.148096] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 66.321230] usb 1-1: configuration #1 chosen from 1 choice [ 66.327265] usb 1-1: New USB device found, idVendor=04a9, idProduct=220d [ 66.327290] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 66.327297] usb 1-1: Product: CanoScan [ 66.327301] usb 1-1: Manufacturer: Canon
# scanimage -d test -T scanimage: scanning image of size 157x196 pixels at 8 bits/pixel scanimage: acquiring gray frame, 8 bits/sample scanimage: reading one scanline, 157 bytes... PASS scanimage: reading one byte... PASS scanimage: stepped read, 2 bytes... PASS scanimage: stepped read, 4 bytes... PASS scanimage: stepped read, 8 bytes... PASS scanimage: stepped read, 16 bytes... PASS scanimage: stepped read, 32 bytes... PASS scanimage: stepped read, 64 bytes... PASS scanimage: stepped read, 128 bytes... PASS scanimage: stepped read, 256 bytes... PASS scanimage: stepped read, 255 bytes... PASS scanimage: stepped read, 127 bytes... PASS scanimage: stepped read, 63 bytes... PASS scanimage: stepped read, 31 bytes... PASS scanimage: stepped read, 15 bytes... PASS scanimage: stepped read, 7 bytes... PASS scanimage: stepped read, 3 bytes... PASS sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter. # Also you need support for SCSI Generic (sg) in your operating system. # If using Linux, try "modprobe sg". found USB scanner (vendor=0x04a9 [Canon], product=0x220d [CanoScan], chip=LM9832/3) at libusb:001:002 # Your USB scanner was (probably) detected. It may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. # Not checking for parallel port scanners. # Most Scanners connected to the parallel port or other proprietary ports # can't be detected by this program. # scanimage -L device `plustek:libusb:001:003' is a Canon CanoScan N670U/N676U/LiDE20 flatbed scanner Но сканнер физически ни хрена не работает!!! 01.03.09, Тихон Тарнавский<[email protected]> написал(а): > On Sat, 28.02.2009 23:38:04 , Иван Лох wrote: >> Если Вы не расковыряли себе Apt::Install-Recommends, >> то этого _достаточно_ для запуска sane-find-scanner. > Недостаточно чётко сформулировал: этого _может быть_ > недостаточно. Прошу прощения, не понял сразу, что имелось ввиду под > умлочанием. > > -- > С уважением, > Тихон Тарнавский. > http://linuxforum.ru > http://posix.ru > > > -- > To UNSUBSCRIBE, email to [email protected] > with a subject of "unsubscribe". Trouble? Contact > [email protected] > > -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected]
