Иван Лох пишет: > On Sat, Apr 04, 2009 at 09:25:23PM +0400, James Brown wrote: > > Я бы начал с обновления BIOS, если это возможно > > >> Эта команда не работает. Пишет, команда не найдена. >> Просто dmesg, в частности, выдает такое: >> ide_generic: please use "probe_mask=0x3f" module parameter for probing >> all legacy ISA IDE ports >> ide_generic: I/O resource 0x1F0-0x1F7 not free. >> ide_generic: I/O resource 0x170-0x177 not free. >> > > Система сообщает, что есть конфликт по адресам ввода вывода. > Рекомендуется вставить директиву > probe_mask=0x3f > при загрузке. > > Просто в промпте grub впечатывайте эту строчку вслед за именем ядра. > > Я бы порекомендовал, дополнительно, вытащить из > компьютера все внешние устройства. > > >> 1:0:0:0: [sdb] Write Protect is off >> sd 1:0:0:0: [sdb] Mode Sense: 1s 00 00 00 >> sd 1:0:0:0: [sdb] Assuming drive cache: write through >> sdb: sdb1 >> Также почему-то не хочет работать USB WiFi карточка >> dmesg ee видит как USB устройство и не ругается >> Но не видит интерфейса wlan0, только eth0 >> > > В-общем, обилие проблем таково, что скорее всего есть проблема > с acpi и/или apic dmesg не говорит о них чего-нибудь интересного? > > > > Вот полный результат работы dmesg : u...@debian:~$ sudo -i debian:~# dmseg -bash: dmseg: command not found debian:~# dmesg [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.26-1-486 (Debian 2.6.26-13) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 Sat Jan 10 17:46:23 UTC 2009 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable) [ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000000edf0000 (usable) [ 0.000000] BIOS-e820: 000000000edf0000 - 000000000edfb000 (ACPI data) [ 0.000000] BIOS-e820: 000000000edfb000 - 000000000ee00000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000000ee00000 - 000000000f000000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] 237MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 60912) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 60912 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 60912 [ 0.000000] On node 0 totalpages: 60912 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 444 pages used for memmap [ 0.000000] Normal zone: 56372 pages, LIFO batch:15 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000F6EF0, 0014 (r0 PTLTD ) [ 0.000000] ACPI: RSDT 0EDF774E, 0028 (r1 PTLTD RSDT 6040000 LTP 0) [ 0.000000] ACPI: FACP 0EDFAF8C, 0074 (r1 SiS M650 6040000 PTL F4240) [ 0.000000] ACPI: DSDT 0EDF7776, 3816 (r1 Clevo 650M 6040000 MSFT 100000D) [ 0.000000] ACPI: FACS 0EDFBFC0, 0040 [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 [ 0.000000] Allocating PCI resources starting at 10000000 (gap: 0f000000:f0f80000) [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000 [ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 00000000000e4000 [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60436 [ 0.000000] Kernel command line: initrd=/live/initrd1.img boot=live union=aufs BOOT_IMAGE=/live/vmlinuz1 [ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic" [ 0.000000] mapped APIC to ffffb000 (011e3000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Detected 2392.641 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.004000] Memory: 230168k/243648k available (1694k kernel code, 12852k reserved, 745k data, 320k init, 0k highmem) [ 0.004000] virtual kernel memory layout: [ 0.004000] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB) [ 0.004000] vmalloc : 0xcf800000 - 0xfffb1000 ( 775 MB) [ 0.004000] lowmem : 0xc0000000 - 0xcedf0000 ( 237 MB) [ 0.004000] .init : 0xc0364000 - 0xc03b4000 ( 320 kB) [ 0.004000] .data : 0xc02a7b13 - 0xc0362000 ( 745 kB) [ 0.004000] .text : 0xc0100000 - 0xc02a7b13 (1694 kB) [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated [ 0.084016] Calibrating delay using timer specific routine.. 4784.52 BogoMIPS (lpj=9569051) [ 0.084174] Security Framework initialized [ 0.084380] SELinux: Disabled at boot. [ 0.084435] Capability LSM initialized [ 0.084503] Mount-cache hash table entries: 512 [ 0.085057] Initializing cgroup subsys ns [ 0.085273] Initializing cgroup subsys cpuacct [ 0.085329] Initializing cgroup subsys devices [ 0.085563] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 0.085652] CPU: L2 cache: 128K [ 0.085859] CPU: Intel(R) Celeron(R) CPU 2.40GHz stepping 09 [ 0.086130] Checking 'hlt' instruction... OK. [ 0.104160] Freeing SMP alternatives: 0k freed [ 0.104371] ACPI: Core revision 20080321 [ 0.122143] ACPI: setting ELCR to 0800 (from 0c20) [ 0.125080] net_namespace: 652 bytes [ 0.125297] Booting paravirtualized kernel on bare hardware [ 0.126231] NET: Registered protocol family 16 [ 0.128039] EISA bus registered [ 0.128131] ACPI: bus type pci registered [ 0.156183] PCI: PCI BIOS revision 2.10 entry at 0xfd9b8, last bus=1 [ 0.156254] PCI: Using configuration type 1 for base access [ 0.156462] Setting up standard PCI resources [ 0.177410] ACPI: EC: Look up EC in DSDT [ 0.186279] ACPI: Interpreter enabled [ 0.186489] ACPI: (supports S0 S3 S4 S5) [ 0.186820] ACPI: Using PIC for interrupt routing [ 0.206379] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 0.222086] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 [ 0.222301] ACPI: EC: driver started in interrupt mode [ 0.222664] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.223500] pci 0000:00:02.0: Enabling SiS 96x SMBus [ 0.225507] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.249762] ACPI: PCI Interrupt Link [LNKA] (IRQs *5) [ 0.250399] ACPI: PCI Interrupt Link [LNKB] (IRQs *10) [ 0.251162] ACPI: PCI Interrupt Link [LNKC] (IRQs 5) *0, disabled. [ 0.251985] ACPI: PCI Interrupt Link [LNKD] (IRQs *11) [ 0.252832] ACPI: PCI Interrupt Link [LNKE] (IRQs *11) [ 0.253454] ACPI: PCI Interrupt Link [LNKF] (IRQs *10) [ 0.254074] ACPI: PCI Interrupt Link [LNKG] (IRQs 10) *0, disabled. [ 0.254895] ACPI: PCI Interrupt Link [LNKH] (IRQs 10) *0, disabled. [ 0.256341] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.256660] pnp: PnP ACPI init [ 0.256880] ACPI: bus type pnp registered [ 0.271727] pnp: PnP ACPI: found 11 devices [ 0.271794] ACPI: ACPI bus type pnp unregistered [ 0.272032] PnPBIOS: Disabled by ACPI PNP [ 0.273815] PCI: Using ACPI for IRQ routing [ 0.274708] ACPI: RTC can wake from S4 [ 0.274987] system 00:04: ioport range 0x8000-0x808f has been reserved [ 0.275193] system 00:04: ioport range 0x8090-0x80ff has been reserved [ 0.275253] system 00:04: ioport range 0x8100-0x811f has been reserved [ 0.275452] system 00:04: ioport range 0x4d0-0x4d1 has been reserved [ 0.275512] system 00:04: ioport range 0xfe00-0xfe00 has been reserved [ 0.275718] system 00:04: iomem range 0xfec00000-0xfecfffff has been reserved [ 0.275780] system 00:04: iomem range 0xfee00000-0xfeefffff has been reserved [ 0.275842] system 00:04: iomem range 0xffc00000-0xffc00fff has been reserved [ 0.276056] system 00:04: iomem range 0xffe00000-0xffe00fff has been reserved [ 0.276121] system 00:04: iomem range 0xffe80000-0xffefffff has been reserved [ 0.308915] PCI: Bridge: 0000:00:01.0 [ 0.308982] IO window: 9000-9fff [ 0.309180] MEM window: 0xec100000-0xec1fffff [ 0.309238] PREFETCH window: 0x00000000f0000000-0x00000000f7ffffff [ 0.309442] PCI: Bus 2, cardbus bridge: 0000:00:0c.0 [ 0.309498] IO window: 0x00002400-0x000024ff [ 0.309555] IO window: 0x00002800-0x000028ff [ 0.309754] PREFETCH window: 0x10000000-0x13ffffff [ 0.309813] MEM window: 0x14000000-0x17ffffff [ 0.310284] pci 0000:00:0c.0: enabling device (0000 -> 0003) [ 0.310913] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 [ 0.310977] PCI: setting IRQ 5 as level-triggered [ 0.310981] ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 0.311451] NET: Registered protocol family 2 [ 0.311977] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.312639] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.312918] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.313161] TCP: Hash tables configured (established 8192 bind 8192) [ 0.313221] TCP reno registered [ 0.313766] NET: Registered protocol family 1 [ 0.314309] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0 [ 0.996017] it is [ 1.829661] Freeing initrd memory: 7541k freed [ 1.832692] audit: initializing netlink socket (disabled) [ 1.832784] type=2000 audit(1238903017.832:1): initialized [ 1.833301] Total HugeTLB memory allocated, 0 [ 1.833811] VFS: Disk quotas dquot_6.5.1 [ 1.833912] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.834194] msgmni has been set to 464 [ 1.834970] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.835058] io scheduler noop registered [ 1.835252] io scheduler anticipatory registered [ 1.835306] io scheduler deadline registered [ 1.835529] io scheduler cfq registered (default) [ 2.270608] pci 0000:01:00.0: Boot video device [ 2.270608] isapnp: Scanning for PnP cards... [ 2.682343] isapnp: No Plug & Play device found [ 2.702383] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 2.703288] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 8250 [ 2.705477] serial 0000:00:02.6: enabling device (0000 -> 0001) [ 2.705554] ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 2.705839] ACPI: PCI interrupt for device 0000:00:02.6 disabled [ 2.715499] brd: module loaded [ 2.716393] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.719531] i8042.c: Detected active multiplexing controller, rev 1.1. [ 2.720967] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.721036] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 2.721234] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 2.721290] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 2.721489] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 2.722616] mice: PS/2 mouse device common for all mice [ 2.724151] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 2.724241] rtc0: alarms up to one year, y3k [ 2.725249] EISA: Probing bus 0 at eisa.0 [ 2.725321] Cannot allocate resource for EISA slot 1 [ 2.725378] Cannot allocate resource for EISA slot 2 [ 2.725596] Cannot allocate resource for EISA slot 8 [ 2.725651] EISA: Detected 0 cards. [ 2.725849] cpuidle: using governor ladder [ 2.725903] cpuidle: using governor menu [ 2.726110] No iBFT detected. [ 2.727261] TCP cubic registered [ 2.727323] NET: Registered protocol family 17 [ 2.727531] Using IPI Shortcut mode [ 2.728449] registered taskstats version 1 [ 2.728994] rtc_cmos 00:02: setting system clock to 2009-04-05 03:43:39 UTC (1238903019) [ 2.730152] Freeing unused kernel memory: 320k freed [ 2.834197] input: AT Translated Set 2 keyboard as /class/input/input0 [ 3.092778] ACPI: ACPI0007:00 is registered as cooling_device0 [ 3.092866] ACPI: Processor [CPU0] (supports 8 throttling states) [ 3.096046] ACPI: LNXTHERM:01 is registered as thermal_zone0 [ 3.096046] ACPI: Thermal Zone [THM0] (51 C) [ 4.050780] No dock devices found. [ 4.061789] SCSI subsystem initialized [ 4.180187] usbcore: registered new interface driver usbfs [ 4.180312] usbcore: registered new interface driver hub [ 4.180491] usbcore: registered new device driver usb [ 4.182329] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.182744] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11 [ 4.182813] PCI: setting IRQ 11 as level-triggered [ 4.182816] ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11 [ 4.182974] ohci_hcd 0000:00:03.0: OHCI Host Controller [ 4.183329] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1 [ 4.183439] ohci_hcd 0000:00:03.0: irq 11, io mem 0xec000000 [ 4.198664] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 4.203787] libata version 3.00 loaded. [ 4.236235] usb usb1: configuration #1 chosen from 1 choice [ 4.236366] hub 1-0:1.0: USB hub found [ 4.236444] hub 1-0:1.0: 3 ports detected [ 4.340280] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.340352] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.340427] usb usb1: Product: OHCI Host Controller [ 4.340482] usb usb1: Manufacturer: Linux 2.6.26-1-486 ohci_hcd [ 4.340539] usb usb1: SerialNumber: 0000:00:03.0 [ 4.341081] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10 [ 4.341149] PCI: setting IRQ 10 as level-triggered [ 4.341153] ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 10 (level, low) -> IRQ 10 [ 4.341316] ohci_hcd 0000:00:03.1: OHCI Host Controller [ 4.341462] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2 [ 4.341569] ohci_hcd 0000:00:03.1: irq 10, io mem 0xec001000 [ 4.396233] usb usb2: configuration #1 chosen from 1 choice [ 4.396359] hub 2-0:1.0: USB hub found [ 4.396435] hub 2-0:1.0: 3 ports detected [ 4.435900] Floppy drive(s): fd0 is 1.44M [ 4.455401] FDC 0 is a National Semiconductor PC87306 [ 4.500327] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.500400] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.500475] usb usb2: Product: OHCI Host Controller [ 4.500530] usb usb2: Manufacturer: Linux 2.6.26-1-486 ohci_hcd [ 4.500588] usb usb2: SerialNumber: 0000:00:03.1 [ 4.500962] ehci_hcd 0000:00:03.2: enabling device (0000 -> 0002) [ 4.501373] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 [ 4.501440] ACPI: PCI Interrupt 0000:00:03.2[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 [ 4.501603] ehci_hcd 0000:00:03.2: EHCI Host Controller [ 4.501752] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3 [ 4.501884] PCI: cache line size of 128 is not supported by device 0000:00:03.2 [ 4.501900] ehci_hcd 0000:00:03.2: irq 10, io mem 0xec002000 [ 4.512081] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 4.512304] usb usb3: configuration #1 chosen from 1 choice [ 4.512426] hub 3-0:1.0: USB hub found [ 4.512504] hub 3-0:1.0: 6 ports detected [ 4.616312] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.616386] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.616460] usb usb3: Product: EHCI Host Controller [ 4.616515] usb usb3: Manufacturer: Linux 2.6.26-1-486 ehci_hcd [ 4.616573] usb usb3: SerialNumber: 0000:00:03.2 [ 4.616694] 8139cp 0000:00:0a.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 4.616775] 8139cp 0000:00:0a.0: Try the "8139too" driver instead. [ 4.616902] ohci1394 0000:00:0b.0: enabling device (0010 -> 0012) [ 4.617295] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 [ 4.617361] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 4.667417] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[ec003800-ec003fff] Max Packet=[2048] IR/IT contexts=[4/8] [ 4.671997] 8139too Fast Ethernet driver 0.9.28 [ 4.681585] Uniform Multi-Platform E-IDE driver [ 4.681660] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 4.683403] 8139too 0000:00:0a.0: enabling device (0000 -> 0003) [ 4.683823] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 [ 4.683889] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 [ 4.684858] eth0: RealTek RTL8139 at 0x2000, 00:90:f5:2a:92:27, IRQ 11 [ 4.684928] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 4.687201] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 [ 4.687273] ACPI: PCI Interrupt 0000:00:02.5[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5 [ 4.687449] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller [ 4.687510] SIS5513: IDE controller (0x1039:0x5513 rev 0x00) at PCI slot 0000:00:02.5 [ 4.687594] SIS5513: not 100% native mode: will probe irqs later [ 4.687668] ide0: BM-DMA at 0x1000-0x1007 [ 4.687735] ide1: BM-DMA at 0x1008-0x100f [ 4.687794] Probing IDE interface ide0... [ 4.976183] hda: TOSHIBA MK4025GAS, ATA DISK drive [ 5.648124] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 5.648185] hda: UDMA/100 mode selected [ 5.648285] Probing IDE interface ide1... [ 5.896008] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090f500002a9227] [ 6.369057] hdc: QSI CD-RW/DVD-ROM SBW242B, ATAPI CD/DVD-ROM drive [ 7.056113] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 7.056645] hdc: UDMA/33 mode selected [ 7.057285] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 7.096005] ide1 at 0x170-0x177,0x376 on irq 15 [ 7.146674] hda: max request size: 128KiB [ 7.148864] hda: 78140160 sectors (40007 MB), CHS=65535/16/63 [ 7.157472] hda: cache flushes supported [ 7.157622] hda: hda1 hda2 < hda5 > [ 7.187187] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache [ 7.187407] Uniform CD-ROM driver Revision: 3.20 [ 8.311631] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports [ 8.311729] ide_generic: I/O resource 0x1F0-0x1F7 not free. [ 8.311788] ide_generic: I/O resource 0x170-0x177 not free. [ 9.777800] NTFS driver 2.1.29 [Flags: R/W MODULE]. [ 19.289383] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } [ 19.289383] hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=18436088, sector=18436088 [ 19.289383] ide: failed opcode was: unknown [ 19.289383] end_request: I/O error, dev hda, sector 18436088 [ 19.289383] NTFS-fs error (device hda1): ntfs_end_buffer_async_read(): Buffer I/O error, logical block 0x1194fb9. [ 28.129099] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } [ 28.129099] hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=18436089, sector=18436089 [ 28.129099] ide: failed opcode was: unknown [ 28.129099] end_request: I/O error, dev hda, sector 18436089 [ 28.129099] NTFS-fs error (device hda1): ntfs_end_buffer_async_read(): Buffer I/O error, logical block 0x1194fba. [ 36.868252] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } [ 36.868252] hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=18436088, sector=18436088 [ 36.868252] ide: failed opcode was: unknown [ 36.868252] end_request: I/O error, dev hda, sector 18436088 [ 36.868252] NTFS-fs error (device hda1): ntfs_end_buffer_async_read(): Buffer I/O error, logical block 0x1194fb9. [ 45.084018] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } [ 45.084018] hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=18436089, sector=18436089 [ 45.084018] ide: failed opcode was: unknown [ 45.084018] end_request: I/O error, dev hda, sector 18436089 [ 45.084018] NTFS-fs error (device hda1): ntfs_end_buffer_async_read(): Buffer I/O error, logical block 0x1194fba. [ 45.084018] NTFS-fs error (device hda1): load_and_init_upcase(): Failed to load $UpCase from the volume. Using default. [ 45.429552] NTFS volume version 3.1. [ 45.429552] NTFS-fs warning (device hda1): load_system_files(): Volume is dirty. Will not be able to remount read-write. Run chkdsk and mount in Windows. [ 45.779198] NTFS volume version 3.1. [ 45.792019] NTFS-fs warning (device hda5): load_system_files(): $LogFile is not clean. Will not be able to remount read-write. Mount in Windows. [ 51.532028] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 51.532028] ISO 9660 Extensions: RRIP_1991A [ 51.583624] aufs 20080714 [ 51.624782] loop: module loaded [ 51.750029] squashfs: version 3.3-CVS (2008/04/04) Phillip Lougher [ 94.863096] udevd version 125 started [ 97.144956] Linux agpgart interface v0.103 [ 97.170995] agpgart: Detected SiS chipset - id:1616 [ 97.175965] agpgart: AGP aperture is 64M @ 0xe8000000 [ 97.325248] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 97.328178] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 97.517490] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100 [ 97.641803] input: Power Button (FF) as /class/input/input1 [ 97.668149] ACPI: Power Button (FF) [PWRF] [ 97.668355] input: Power Button (CM) as /class/input/input2 [ 97.700171] ACPI: Power Button (CM) [PWRB] [ 97.700353] input: Sleep Button (CM) as /class/input/input3 [ 97.728142] ACPI: Sleep Button (CM) [SLPB] [ 97.728405] input: Lid Switch as /class/input/input4 [ 97.740492] ACPI: Lid Switch [LID] [ 97.764299] ACPI: AC Adapter [ADP0] (on-line) [ 97.765739] ACPI: Battery Slot [BAT0] (battery absent) [ 99.516857] ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 99.559821] Intel ICH 0000:00:02.7: enabling device (0000 -> 0001) [ 99.559904] ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 99.861146] input: PC Speaker as /class/input/input5 [ 100.213472] input: PS/2 Mouse as /class/input/input6 [ 100.257781] input: AlpsPS/2 ALPS GlidePoint as /class/input/input7 [ 100.345685] NET: Registered protocol family 23 [ 100.400082] intel8x0_measure_ac97_clock: measured 53516 usecs [ 100.400151] intel8x0: clocking to 48000 [ 100.400853] Yenta: CardBus bridge found at 0000:00:0c.0 [1558:2263] [ 100.400946] Yenta: Using CSCINT to route CSC interrupts to PCI [ 100.401003] Yenta: Routing CardBus interrupts to PCI [ 100.401062] Yenta TI: socket 0000:00:0c.0, mfunc 0x00001002, devctl 0x44 [ 100.534215] parport_pc 00:09: reported by Plug and Play ACPI [ 100.534410] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 100.628576] nsc-ircc, chip->init [ 100.628648] nsc-ircc, Found chip at base=0x02e [ 100.628730] nsc-ircc, driver loaded (Dag Brattli) [ 100.628791] nsc_ircc_open(), can't get iobase of 0x2f8 [ 100.628878] nsc-ircc, Found chip at base=0x02e [ 100.628959] nsc-ircc, driver loaded (Dag Brattli) [ 100.629015] nsc_ircc_open(), can't get iobase of 0x2f8 [ 100.629275] nsc-ircc 00:0a: disabled [ 100.640318] Yenta: ISA IRQ mask 0x0210, PCI irq 5 [ 100.640386] Socket status: 30000006 [ 104.177557] eth0: link down [ 178.084773] NET: Registered protocol family 10 [ 178.085503] lo: Disabled Privacy Extensions [ 178.086144] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 178.658700] lp0: using parport0 (interrupt-driven). [ 178.673077] ppdev: user-space parallel port driver [ 291.884965] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 [ 291.884965] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 292.080026] eth0: link down [ 302.612041] eth0: no IPv6 routers present [ 333.627025] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
Вроде бы на acpi не ругается, если я правильно понимаю. Apic выключен, а он нужен для однопроцессорного ноута? Вроде бы он необходим для двухпроцессорника или многопроцессорника? Почему то показывает что eth0 down, когда он "up"? и я через него почту шлю :-) -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected]
