On Wed, 2012-11-14 at 12:47 +0000, Kaya Saman wrote: > Hi Frans, > > previously I got the firmware directly from the site above and simply > did a wget to put it into the /lib/firmware directory. > > As of now I did what Patrick suggested and ran: apt-get install > firmware-linux-nonfree > > It still didn't work :-( > > [ 43.836916] tg3 0000:00:02.0: eth0: Tigon3 [partno(none) rev 2100] > (PCI:66MHz:64-bit) MAC address 00:14:4f:5d:1e:7e > [ 43.974266] tg3 0000:00:02.0: eth0: attached PHY is 5704 > (10/100/1000Base-T Ethernet) (WireSpeed[1]) > [ 44.094448] tg3 0000:00:02.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] > ASF[0] TSOcap[1] > [ 44.198525] tg3 0000:00:02.0: eth0: dma_rwctrl[763f0000] dma_mask[32-bit] > [ 45.138092] tg3 0003:00:02.0: eth1: Tigon3 [partno(none) rev 2100] > (PCI:66MHz:64-bit) MAC address 00:14:4f:5d:1e:80 > [ 45.275418] tg3 0003:00:02.0: eth1: attached PHY is 5704 > (10/100/1000Base-T Ethernet) (WireSpeed[1]) > [ 45.395593] tg3 0003:00:02.0: eth1: RXcsums[1] LinkChgREG[0] MIirq[0] > ASF[0] TSOcap[1] > [ 45.499671] tg3 0003:00:02.0: eth1: dma_rwctrl[763f0000] dma_mask[32-bit] > [ 83.749175] tg3 0000:00:02.0: eth0: No firmware running > [ 83.866559] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 85.411107] tg3 0000:00:02.0: eth0: Link is up at 100 Mbps, full duplex > [ 85.498042] tg3 0000:00:02.0: eth0: Flow control is off for TX and > off for RX > [ 85.593597] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 91.991628] tg3 0003:00:02.0: eth1: No firmware running > [ 92.102114] ADDRCONF(NETDEV_UP): eth1: link is not ready > > Here is requested output: > > # ls -l /lib/firmware/tigon > total 16 > -rw-r--r-- 1 root root 2668 Sep 19 2011 tg3.bin > -rw-r--r-- 1 root root 3884 Sep 19 2011 tg3_tso5.bin > -rw-r--r-- 1 root root 7004 Sep 19 2011 tg3_tso.bin > > # ifconfig > eth0 Link encap:Ethernet HWaddr 00:14:4f:5d:1e:7e > inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:6504 errors:0 dropped:0 overruns:0 frame:0 > TX packets:3567 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:461831 (451.0 KiB) TX bytes:274816 (268.3 KiB) > Interrupt:6 > > eth1 Link encap:Ethernet HWaddr 00:14:4f:5d:1e:80 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > Interrupt:31 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:124 errors:0 dropped:0 overruns:0 frame:0 > TX packets:124 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:10162 (9.9 KiB) TX bytes:10162 (9.9 KiB) > > > uname -a shows: > > 2.6.32-5-sparc64 #1 Sun Sep 23 10:01:20 UTC 2012 sparc64 GNU/Linux
Hi Kaya, That's clear. For me, just to be sure, what does these two do? # ifconfig eth1 192.168.2.116 up # ping 192.168.2.116 Check your settings with # ifconfig again. And does # update-initramfs also complains about the missing firmware files, as asked? Thanks, Frans van Berckel -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
