In der Bootdisk-HOWTO steht was diese Lilo-Meldungen bedeuten; Ein Ausschnitt: L. LILO boot error codes. Questions about these errors are asked so often on Usenet that we include them here as a public service. This summary is excerpted from Werner Almsberger's LILO User Documentation, available at <http://sunsite.unc.edu/pub/Linux/system/boot/lilo/lilo-u-20.ps.gz>. When LILO loads itself, it displays the word ``LILO''. Each letter is printed before or after performing some specific action. If LILO fails at some point, the letters printed so far can be used to identify the problem. (nothing) No part of LILO has been loaded. LILO either isn't installed or the partition on which its boot sector is located isn't active. L The first stage boot loader has been loaded and started, but it can't load the second stage boot loader. The two-digit error codes indicate the type of problem. (See also section ``Disk error codes''.) This condition usually indicates a media failure or a geometry mismatch (e.g. bad disk parameters) LI The first stage boot loader was able to load the second stage boot loader, but has failed to execute it. This can either be caused by a geometry mismatch or by moving /boot/boot.b without running the map installer. LIL The second stage boot loader has been started, but it can't load the descriptor table from the map file. This is typically caused by a media failure or by a geometry mismatch. LIL? The second stage boot loader has been loaded at an incorrect address. This is typically caused by a subtle geometry mismatch or by moving /boot/boot.b without running the map installer. LIL- The descriptor table is corrupt. This can either be caused by a geometry mismatch or by moving /boot/map without running the map installer. LILO All parts of LILO have been successfully loaded. If the BIOS signals an error when LILO is trying to load a boot image, the respective error code is displayed. These codes range from 0x00 through 0xbb. See the LILO User Guide for an explanation of these.
On Wed, 12 May 1999, Ansgar Hellwig wrote: SC>[EMAIL PROTECTED] schrieb am Wed, May 12, 1999 um 10:33:56AM +0200: SC>> SC>> hi... SC>> Ich verbrachte die letzten 2 abende dabei in meinem Misch-system LILO zu SC>> benützen, jedoch bringen mich how-to/faq und readmes nicht mehr weiter. SC>> Also ich habe 1 SCSI(sda1(win),sda2(/swap),sda3(/home)) und 1 IDE SC>> Platte(hda1(/boot)<1024cyl.,hda2(win),hda3(/)). Gebootet wird von scsi. jedoch SC>> bekomme ich nicht mehr als ein "LI" zu sehen. SC>> SC> SC> SC>Hallo! SC> SC>Versuch mal folgendes in die lilo.conf zu schreiben: SC> SC>disk = /dev/sda SC> bios = 0x80 SC>disk = /dev/hda SC> bios = 0x81 SC> SC> SC>Und wech... SC>Ansgar Hellwig SC> SC>-- SC>****************************************************************** SC>* Ansgar Hellwig WWW: http://hrz.uni-paderborn.de/~f35864/ SC>* Mail: [EMAIL PROTECTED] SC>* SC>------------------------------------------------ SC>Um sich aus der Liste auszutragen schicken Sie SC>bitte eine E-Mail an [EMAIL PROTECTED] die im Body SC>"unsubscribe debian-user-de <deine emailadresse>" SC>enthaelt. SC>Bei Problemen bitte eine Mail an: [EMAIL PROTECTED] SC>------------------------------------------------ SC>Anzahl der eingetragenen Mitglieder: 738 -- ,---._________________________________ / \ |~~\_____/~~\__ | | [EMAIL PROTECTED] >---\______====== )-+ | ,---._______________________________/ ~~~|/~~ | |/ () ------------------------------------------------ Um sich aus der Liste auszutragen schicken Sie bitte eine E-Mail an [EMAIL PROTECTED] die im Body "unsubscribe debian-user-de <deine emailadresse>" enthaelt. Bei Problemen bitte eine Mail an: [EMAIL PROTECTED] ------------------------------------------------ Anzahl der eingetragenen Mitglieder: 736
