Hallo Liste!
In meinem Rechner habe ich folgende SCSI Komponenten:
0. Sybios Logic 8751 SP UW
1. IBM DDRS 4.3 GB
2. Archive Viper Tape Drive (Streamer)
3. Plasmon CDR 4220 CD-Brenner
Folgendes Problem: Wenn ich den Brenner mit anschließe kann ich nicht auf
ihn zugreifen, weil der SCSI-Bus immer wieder Resetetetet wird. Selbst
die Schublade läßt sich auf Knopfdruck nicht mehr öffnen. Terminiert habe
ich den Brenner, da er die letzte Komponente im Bus ist.
Wie kann ich dem Brenner abgewöhnen das er immer nach einer "CD sucht"
bedingt durch den SCSI-Reset?
...tschau
Christian
Email: [EMAIL PROTECTED] take a look at: www.hotel-ummen.de
[EMAIL PROTECTED] www.laibreport.de
[EMAIL PROTECTED]
May 17 20:11:19 Brisko kernel: Floppy drive(s): fd0 is 1.44M
May 17 20:11:19 Brisko kernel: FDC 0 is a post-1991 82077
May 17 20:11:19 Brisko kernel: md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
May 17 20:11:19 Brisko kernel: ncr53c8xx: at PCI bus 0, device 17, function 0
May 17 20:11:19 Brisko kernel: ncr53c8xx: 53c875 detected with Symbios NVRAM
May 17 20:11:19 Brisko kernel: ncr53c875-0: rev=0x04, base=0xee001000,
io_port=0xe800, irq=9
May 17 20:11:19 Brisko kernel: ncr53c875-0: Symbios format NVRAM, ID 7,
Fast-20, Parity Checking
May 17 20:11:19 Brisko kernel: ncr53c875-0: initial
SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/4e/80/01/00/24
May 17 20:11:19 Brisko kernel: ncr53c875-0: final
SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/a0/00/08/24
May 17 20:11:19 Brisko kernel: ncr53c875-0: on-board RAM at 0xee000000
May 17 20:11:19 Brisko kernel: ncr53c875-0: on-board ram mapped at virtual
address 0x8807000
May 17 20:11:19 Brisko kernel: ncr53c875-0: requesting shared irq 9
(dev_id=0x8080)
May 17 20:11:19 Brisko kernel: ncr53c875-0: resetting, command processing
suspended for 2 seconds
May 17 20:11:19 Brisko kernel: ncr53c875-0: restart (scsi reset).
May 17 20:11:19 Brisko kernel: ncr53c875-0: enabling clock multiplier
May 17 20:11:19 Brisko kernel: ncr53c875-0: copying script fragments into the
on-board RAM ...
May 17 20:11:19 Brisko kernel: ncr53c875-0: command processing resumed
May 17 20:11:19 Brisko kernel: Failed initialization of WD-7000 SCSI card!
May 17 20:11:19 Brisko kernel: scsi0 : ncr53c8xx - revision 2.5f.1
May 17 20:11:19 Brisko kernel: scsi : 1 host.
May 17 20:11:19 Brisko kernel: Vendor: IBM Model: DDRS-34560W
Rev: S97B
May 17 20:11:19 Brisko kernel: Type: Direct-Access
ANSI SCSI revision: 02
May 17 20:11:19 Brisko kernel: Detected scsi disk sda at scsi0, channel 0, id
0, lun 0
May 17 20:11:19 Brisko kernel: Vendor: PLASMON Model: CDR4220
Rev: 1.20
May 17 20:11:19 Brisko kernel: Type: CD-ROM
ANSI SCSI revision: 02
May 17 20:11:19 Brisko kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id
2, lun 0
May 17 20:11:19 Brisko kernel: scsi0 : channel 0 target 2 lun 1 request sense
failed, performing reset.
May 17 20:11:19 Brisko kernel: SCSI bus is being reset for host 0 channel 0.
May 17 20:11:19 Brisko kernel: ncr53c8xx_reset: pid=12 reset_flags=1
serial_number=0 serial_number_at_timeout=0
May 17 20:11:19 Brisko kernel: ncr53c875-0: resetting, command processing
suspended for 2 seconds
May 17 20:11:19 Brisko kernel: ncr53c875-0: restart (scsi reset).
May 17 20:11:19 Brisko kernel: ncr53c875-0: enabling clock multiplier
May 17 20:11:19 Brisko kernel: ncr53c875-0: copying script fragments into the
on-board RAM ...
May 17 20:11:19 Brisko kernel: ncr53c875-0: command processing resumed
May 17 20:11:19 Brisko kernel: Vendor: ARCHIVE Model: VIPER 2525 25462
Rev: -007
May 17 20:11:19 Brisko kernel: Type: Sequential-Access
ANSI SCSI revision: 01
May 17 20:11:19 Brisko kernel: scsi : detected 1 SCSI cdrom 1 SCSI disk total.
May 17 20:11:19 Brisko kernel: ncr53c875-0-<0,0>: WIDE SCSI (16 bit) enabled.
May 17 20:11:19 Brisko kernel: ncr53c875-0-<0,0>: FAST-20 WIDE SCSI 40.0 MB/s
(50 ns, offset 15)
May 17 20:11:19 Brisko kernel: SCSI device sda: hdwr sector= 512 bytes.
Sectors= 8925000 [4357 MB] [4.4 GB]
May 17 20:11:19 Brisko kernel: Partition check:
May 17 20:11:19 Brisko kernel: sda: sda1 sda2 sda3 sda4
