Le Tue, 05 Apr 2005 19:30:59 +0200 fred <[EMAIL PROTECTED]> a �crit: > Ou alors elle me ment. > > eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 > eth0: Promiscuous mode enabled.
Tu as un sniffer??? > > �a, c'est dans les messages de log. > Maintenant si je lance un rtl8139-diag, il ne me r�pond pas la m�me > chose : half-duplex. > > rtl8139-diag.c:v2.11 4/22/2003 Donald Becker ([EMAIL PROTECTED]) > http://www.scyld.com/diag/index.html > Index #1: Found a RealTek RTL8139 adapter at 0xa400. > Realtek station address 00:40:f4:7d:01:11, chip type 'rtl8139C'. > Receiver configuration: Promiscuous > Rx FIFO threshold 2048 bytes, maximum burst 2048 bytes, 32KB ring > Transmitter enabled with NONSTANDARD! settings, maximum burst 1024 > bytes. Flow control: Tx disabled Rx disabled. > The chip configuration is 0x10 0x8d, MII half-duplex mode. > No interrupt sources are pending. Rtl8139 avec mii-diag en auto 100FD: totoche:/home/francois# mii-diag Using the default interface 'eth0'. Basic registers of MII PHY #32: 1100 782d 0000 0000 01e1 45e1 0001 0000. The autonegotiated capability is 01e0. The autonegotiated media type is 100baseTx-FD. Basic mode control register 0x1100: Auto-negotiation enabled. You have link beat, and everything is working OK. Your link partner advertised 45e1: Flow-control 100baseTx-FD 100baseTx 10baseT-FD 10baseT, w/ 802.3X flow control. End of basic transceiver informaion. Avec rtl8139-diag install� pour l'occasion: totoche:/home/francois# rtl8139-diag rtl8139-diag.c:v2.03 5/15/2001 Donald Becker ([EMAIL PROTECTED]) http://www.scyld.com/diag/index.html Index #1: Found a RealTek RTL8139 adapter at 0x3000. EEPROM size test returned 6, 0x204a4 / 0. Would write new Default Media entry 0x0000 to offset 6, the current value is 0xe512. Use '-a' or '-aa' to show device registers, '-e' to show EEPROM contents, -ee for parsed contents, or '-m' or '-mm' to show MII management registers. totoche:/home/francois# (je vire cette cochonnerie (rtl-8139) qui ne marche pas) Avec mii-tool: totoche:/home/francois# mii-tool eth0: negotiated 100baseTx-FD, link ok totoche:/home/francois# Sur une 10HD forc�e: cerbere:/home/francois# mii-diag eth1 Basic registers of MII PHY #32: 0000 780d 0000 0000 01e1 0000 0000 0000. Basic mode control register 0x0000: Auto-negotiation disabled, with Speed fixed at 10 mbps, half-duplex. You have link beat, and everything is working OK. Link partner information information is not exchanged when in fixed speed mode. End of basic transceiver informaion. Essayes donc d'installer mii-diag (#apt-get install mii-diag), que'st ce qu'il donne? -- Pensez � lire la FAQ de la liste avant de poser une question : http://wiki.debian.net/?DebianFrench Pensez � rajouter le mot ``spam'' dans vos champs "From" et "Reply-To:" To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
