Bonjour,
Apr�s quelques recherches infructeuses dans les archives des listes
Debien et dans la documentation du kernel, je dois me tourner vers vous.
Voil� mon petit probl�me :
Apr�s t�l�chargement et installation d'un kernel-2.4.9-586 de Debian,
changement du lilo.conf pour prendre en compte le initrd (nouveau depuis
le 2.2.17 que j'avais avant ...) he ben au d�marrage, apr�s chargement
du ramdisk (normal apparemment) et prompt pour avoir le shell , il me
fait un "kernel panic : attempt to kill init" et bloque l� !!!
Qu'est ce que j'ai fait (ou plut�t pas fait) de mal pour tant de haine ?
Heureusement j'avais encore l'ancien kernel en secours sinon ...
Le initrd fournit avec le kernel serait-il incomplet ? Faut-il y changer
quelquechose, ajouter un programme, une commande ?
Je joint mon lilo.conf au cas o� ...
Merci d'avance
Didier
--
+---- \\\// --[Didier Link -> [EMAIL PROTECTED]
| (0 -) |
+-oOO--(_)--OOo-------- -> Use Debian GNU/LinuX <- -----------+
-+
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda2
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
#
install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
#delay=0
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
message=/boot/bootmess.txt
prompt
# single-key
delay=100
timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
vga=ask
# vga=9
# vga=extended
# vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=Linux
image=/vmlinuz
label=Linux
read-only
initrd=/boot/initrd
append="root=/dev/rd/0 init=/linuxrc rw"
# restricted
# alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
