D�sol� de re-poster pour un probl�me non r�solu :
Si je lance sane-find-scanner, il d�tecte correctement mon scanner USB
[un Canon N 1220 U) , mais si je lance xsane ,j'ai la r�ponse suivante :
Aucun p�riph�rique disponible.
J'ai cherch� sur les archives de la liste et je n'ai rien trouv� ...
bien que l'on m'ait dit que j'y trouverais des r�ponses
Et je ne comprends pas pourquoi �a ne marche pas ....
Si j'ai bien saisi, il y a deux fichiers � modifier
/etc/sane.d/dll.conf et /etc/sane.d/plustek.conf [Mon scanner est en
fait - � cause de la puce - reconnu comme unplustek]
Je joins ces deux fichiers , pour que les �ventuels "secouristes" , plus
au fait de ces choses, me donnent leur avis.
Merci
Claude
# enable the next line if you want to allow access through the network:
net
#abaton
#agfafocus
#apple
#avision
#artec
#artec_eplus48u
#as6e
#bh
#canon
#canon630u
#canon_pp
#coolscan
#coolscan2
#dc25
#dc210
#dc240
#dmc
#epson
#fujitsu
#gt68xx
#hp
#hpsj5s
#leo
#matsushita
#microtek
#microtek2
#mustek
#mustek_pp
#mustek_usb
#nec
#pie
#pint
plustek_USB
#pnm
#qcam
#ricoh
#s9036
#sceptre
#sharp
#sm3600
#snapscan
#sp15c
#st400
#tamarack
#teco1
#teco2
#teco3
#test
#umax
#umax_pp
#umax1220u
#v4l
#
#
#
# The following backends are not part of the SANE distribution
# but are provided by the libsane-extras Debian package
#hp4200
#niash
# The HP OfficeJet backend is not part of the SANE distribution
# but is provided by the hpoj Debian package
#hpoj
# Plustek-SANE Backend configuration file
# For use with Plustek parallel-port scanners and
# LM9831/2/3 based USB scanners
#
# For parport devices use the parport section
#
#[parport]
#device /dev/pt_drv
#
# leave the default values as specified in /etc/modules.conf
#
option warmup -1
option lOffOnEnd -1
option lampOff -1
#
# The USB section:
# each device needs at least two lines:
# - [usb] vendor-ID and product-ID
# - device devicename
# i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)
# [usb] 0x07B3 0x0017
# device /dev/usbscanner
# or
# device libusb:bbb:ddd
# where bbb is the busnumber and ddd the device number
# make sure that your user has access to /proc/bus/usb/bbb/ddd
#
# additionally you can specify some options
# warmup, lOffOnEnd, lampOff
#
# For autodetection use
# [usb]
# device /dev/usbscanner
#
# or simply
# [usb]
#
# or if you want a specific device but you have no idea about
# the device node or you use libusb, simply set vendor- and product-ID
# [usb] 0x07B3 0x0017
# device auto
#
# NOTE: autodetection is safe, as it uses the info it got
# from the USB subsystem. If you're not using the
# autodetection, you MUST have attached that device
# at your USB-port, that you have specified...
#
#[usb]
[USB] 0x04A9 0x2207
device /dev/usb/scanner0
#
# options for the previous USB entry
#
# switch lamp off after xxx secs, 0 disables the feature
option lampOff 300
# warmup period in seconds, 0 means no warmup
option warmup 15
# 0 means leave lamp-status untouched, not 0 means switch off
# on sane_close
option lOffOnEnd 1
#
# options to tweak the image start-position
# (WARNING: there's no internal range check!!!)
#
# for the normal scan area
#
option posOffX 0
option posOffY 0
# for transparencies
option tpaOffX 0
option tpaOffY 0
# for negatives
option negOffX 0
option negOffY 0
#
# for setting the calibration strip position
# (WARNING: there's no internal range check!!!)
# -1 means use built in
#
option posShadingY -1
option tpaShadingY -1
option negShadingY -1
#
# to invert the negatives, 0 disables the feature
#
option invertNegatives 0
# for skipping whole calibration step
option skipCalibration 0
# for skipping entire fine calibration step
# coarse calibration is done
option skipFine 0
# discard the result of the fine white calibration
option skipFineWhite 0
# for replacing the gain values found during
# calibration
option red_gain -1
option green_gain -1
option blue_gain -1
#
# for adjusting the default gamma values
#
option redGamma 1.0
option greenGamma 1.0
option blueGamma 1.0
option grayGamma 1.0
#
# to enable TPA (non Plustek devices only)
# 0 means default behaviour as specified in the internal tables
# 1 means enable
#
option enableTPA 0
#
# and of course the device-name
#
# device /dev/usbscanner
device auto
#
# to define a new device, start with a new section:
# [USB] or [PARPORT]
#
