Bonjour,
J'ai un souci assez myst�rieux avec un graveur de CD-ROM IDE :
A la base j'ai une configuration enti�rement SCSI :
Adaptec 2940 U2W
1 disque dur 9,1 GO IBM U2W LVD
2 disques durs 4,3 GO UW en miroir (Software RAID)
1 lecteur de CD ROM Plextor 40x Ultra-SCSI.
Pour le reste : Carte-m�re ASUS A7V333, Carte Video Matrox G400, Carte
r�seau Intel EtherExpress 10/100, Carte son SoundBlaster Live, Athlon
XP2200+ et 512 MB de RAM.
La distribution est une debian testing.
Cela fait plusieurs semaines que cette config tourne sans aucun souci
avec un kernel 2.6.8-1-k7
Ayant r�cup�r� un graveur Lite-On d'une autre config je pensais
l'installer sur cette machine.
Apr�s le branchement (il est seul en master sur l'interface IDE
secondaire) je red�marre et le BIOS le d�tecte sans probl�me.
Par contre le noyau lui reste muet, ce qui m'�tonne le plus c'est
qu'aucune interface IDE ne soit d�tect�e. Pour pr�ciser cette CM est
�quip�e d'un controleur RAID PROMISE qui est d�sactiv� par Jumper sur la
CM et d'une carte son AC97 elle aussi d�sactiv�e. Dans le BIOS les deux
interfaces IDE sont activ�es (primaire et secondaire).
J'ai mis la sortie compl�te de dmesg � la fin mais pour faire plus court
voici le r�sultat de deux commandes :
13:55 [EMAIL PROTECTED] ~% dmesg | grep IDE
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
14:17 [EMAIL PROTECTED] ~% dmesg | grep ide
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
13:57 [EMAIL PROTECTED] ~% dmesg | grep CD
Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
Le plus �tonnant reste l'IDE qui ne d�tecte rien.
Les modules charg�s sont les suivants : (je ne prends que l'ide)
14:00 [EMAIL PROTECTED] ~% lsmod | grep ide
ide_core 138788 1 via82cxxx
14:00 [EMAIL PROTECTED] ~% lsmod | grep cdrom
cdrom 40284 1 sr_mod
Je sais qu'il faut utiliser l'�mulation ide-scsi pour utiliser un
graveur mais il n'apparait pas dans la liste des p�riph�riques IDE ce
qui me donnerait au moins la possibilit� de l'utiliser comme lecteur
pour v�rifier son fonctionnement.
L'interface IDE existe pourtant bien sur le bus PCI :
14:05 [EMAIL PROTECTED] ~% lspci
...
0000:00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
...
Apr�s moultes recherches et un bug debian approchant (le #210612 mais
sans r�ponse) j'avoue rester sec. Il semblerait que les chipsets VIA
posent parfois des probl�mes mais pas de ce genre l�. J'en viens � me
demander si le fait d'avoir le SCSI charg� avant ne pose pas des probl�mes.
Si quelqu'un a une id�e je suis preneur...
Merci d'avance.
Florent.
PS : un coup d'oeil � dmesg complet me donne �a :
13:55 [EMAIL PROTECTED] ~% dmesg
1799.0832 MHz.
..... host bus clock speed is 266.0641 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4640k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf17e0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f9a40
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9a70, dseg 0xf0000
pnp: 00:11: ioport range 0x290-0x297 has been reserved
pnp: 00:11: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:11: ioport range 0xe400-0xe47f has been reserved
pnp: 00:11: ioport range 0xec00-0xec3f has been reserved
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:09.1[B] -> GSI 16 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:09.2[C] -> GSI 17 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 19 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 185
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178002
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0002
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 B9
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 C1
13 001 01 1 1 0 1 0 1 1 B1
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 C9
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ185 -> 0:16
IRQ169 -> 0:17
IRQ193 -> 0:18
IRQ177 -> 0:19
IRQ201 -> 0:21
.................................... done.
Simple Boot Flag at 0x3a set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:09.0, from 3 to 1
PCI: Via IRQ fixup for 0000:00:09.1, from 11 to 9
PCI: Via IRQ fixup for 0000:00:11.2, from 0 to 9
PCI: Via IRQ fixup for 0000:00:11.3, from 5 to 9
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4640 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 193
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
Using anticipatory io scheduler
(scsi0:A:1): 80.000MB/s transfers (40.000MHz, offset 31, 16bit)
Vendor: IBM Model: DNES-309170W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled. Depth 8
(scsi0:A:2): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
Vendor: IBM-PCCO Model: DDRS-34560W !# Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:2:0: Tagged Queuing enabled. Depth 8
(scsi0:A:3): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
Vendor: IBM Model: DDRS-34560W Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:3:0: Tagged Queuing enabled. Depth 8
(scsi0:A:6): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 p4 < p5 p6 p7 >
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SCSI device sdb: 8813870 512-byte hdwr sectors (4513 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host0/bus0/target2/lun0: p1
Attached scsi disk sdb at scsi0, channel 0, id 2, lun 0
SCSI device sdc: 8925000 512-byte hdwr sectors (4570 MB)
SCSI device sdc: drive cache: write back
/dev/scsi/host0/bus0/target3/lun0: p1
Attached scsi disk sdc at scsi0, channel 0, id 3, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS on sda2, internal journal
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <[EMAIL PROTECTED]>
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
Capability LSM initialized
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: md0 stopped.
md: bind<sdc1>
md: bind<sdb1>
md: raid1 personality registered as nr 3
raid1: raid set md0 active with 2 out of 2 mirrors
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 1223 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[169]
MMIO=[f3000000-f30007ff] Max Packet=[2048]
irda_init()
NET: Registered protocol family 23
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 169
e100: eth0: e100_probe: addr 0xf5000000, irq 169, MAC addr 00:04:AC:98:4E:16
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000001f729]
ip1394: $Rev: 1224 $ Ben Collins <[EMAIL PROTECTED]>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Creative EMU10K1 PCI Audio Driver, version 0.20a, 00:12:35 Sep 14 2004
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 19 (level, low) -> IRQ 177
emu10k1: EMU10K1 rev 6 model 0x8027 found, IO at 0xb400-0xb41f, IRQ 177
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:00:09.2[C] -> GSI 17 (level, low) -> IRQ 169
ehci_hcd 0000:00:09.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:09.2: irq 169, pci mem e09f9000
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
parport0: Printer, HEWLETT-PACKARD DESKJET 980C
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
Real Time Clock Driver v1.12
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xf8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:09.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:09.0: irq 177, io base 0000d800
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:09.1[B] -> GSI 16 (level, low) -> IRQ 185
uhci_hcd 0000:00:09.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:09.1: irq 185, io base 0000d400
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:11.2: irq 201, io base 0000a400
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#4)
uhci_hcd 0000:00:11.3: irq 201, io base 0000a000
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<[EMAIL PROTECTED]> and others
gameport: pci0000:00:10.1 speed 1217 kHz
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ttyS0: LSR safety check engaged!
ttyS0: LSR safety check engaged!
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f8de0(lo)
IPv6 over IPv4 tunneling driver
lp0: using parport0 (interrupt-driven).
lp0: ECP mode
eth0: no IPv6 routers present
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
[drm] Initialized mga 3.1.0 20021029 on minor 0: Matrox Graphics, Inc.
MGA G400 AGP
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
--
L'oeil humain est une m�canique merveilleuse dont la r�ussite parfaite nous conforte dans notre foi en Dieu. On regrettera seulement que l'oeil du cochon d'Inde ou du verrat p�rigourdin b�n�ficie de la m�me g�niale
complexit�.
-+- Pierre Desproges -+-
