> Pour avoir i2c-dev : si tu utilises menuconfig, voici la marche �
suivre
>
> make menuconfig
>
> section device driver puis sous section I2C support et enfin tu mets
en
> module I2C device interface
Merci �a a march�.
Voici ce que j'ai mis comme configuration du kernel.
# cat /boot/config-2.6.8-i2c03 |grep -i i2c
# I2C support
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
# I2C Algorithms
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
# I2C Hardware Bus support
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_ELEKTOR is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
CONFIG_I2C_VIAPRO=m
# CONFIG_I2C_VOODOO3 is not set
CONFIG_I2C_SENSOR=m
# Other I2C Chip support
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
%%%%%%%%%%%%%%%%%%%%%%%
* Code maturity level options
o [*] Prompt for development and/or incomplete code/drivers
* Bus options (PCI, PCMCIA, EISA, MCA, ISA)
o [*] PCI support
o [*] ISA support (not needed anymore since 2.6.2-rc1)
* Device Drivers
o I2C Support
+ <M> I2C Support
+ <M> I2C device interface
+ I2C Algorithms
# <M> (j'ai tout mis en M)
+ I2C Hardware Bus support
# <M> (Ca depend du materiel faire un #lspci -v
pour retrouver ses petits)
+ I2C Hardware Sensors Chip support
# <M> (idem faire un lspci -v)
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
Ensuite un #sensors-detect m'a dit qu'il manquait rivatv.
J'ai fait une installation automatique des lignes n�cessaires
dans /etc/modules puis quelques modifs recommand�es � /etc/sensors.conf
qui n'ont pas chang� grand chose.
et $sensors:
asb100-i2c-0-2d
Adapter: SMBus Via Pro adapter at e800
VCore 1: +1.74 V (min = +1.62 V, max = +1.79 V)
+3.3V: +3.26 V (min = +3.14 V, max = +3.47 V)
+5V: +4.81 V (min = +4.76 V, max = +5.24 V)
+12V: +12.65 V (min = +10.82 V, max = +13.19 V)
-12V (reserved):
-13.21 V (min = -0.00 V, max = -0.00 V)
-5V (reserved):
-5.52 V (min = -0.00 V, max = -0.00 V)
CPU Fan: 4623 RPM (min = 1997 RPM, div = 4)
Chassis Fan:
0 RPM (min = 3994 RPM, div = 2)
Power Fan: 0 RPM (min = 3994 RPM, div = 2)
M/B Temp: +33�C (high = +45�C, hyst = +40�C)
CPU Temp (Intel):
+76�C (high = +60�C, hyst = +50�C)
Power Temp:
+14�C (high = +45�C, hyst = +40�C)
CPU Temp (AMD):
+56�C (high = +60�C, hyst = +50�C)
vid: +1.700 V (VRM Version 9.0)
alarms:
Je comprends pas trop pourquoi j'ai un CPU intel +76�C je n'ai qu'un
Athlon.
Quelqu'un a une id�e pour r�gler ce probl�me.
Merci
--
Pensez � lire la FAQ de la liste avant de poser une question :
http://wiki.debian.net/?DebianFrench
Pensez � rajouter le mot ``spam'' dans vos champs "From" et "Reply-To:"
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
