Hallo zusammen, ich bem�he mich seit l�ngerer zeit darum, Sedlbauer Speedfax+ und Hylafax zum Laufen zu bringen.
Der Faxempfang scheint zu funktionieren. Beim Versandversuch erhalten Meldungen, wie diese angeh�ngt per Mail. Kann mir jemand sagen, was dort schief l�uft? Die Konfiguration wurde mir von der Fa. Seldbauer zur Verf�gung gestellt, dennoch scheint es Probleme mit dem AT+FTS=7 zu geben... Vielen Dank! Michael Hierweck
--- Begin Message ---
Your facsimile job to 02314650137 was not sent because:
Stop and wait failure (modem on hook)
The job will be retried at 11:29.
---- Transcript of session follows ----
May 27 11:28:29.32: [10882]: SESSION BEGIN 00000089 492314650137
May 27 11:28:29.32: [10882]: HylaFAX (tm) Version 4.1.1
May 27 11:28:29.45: [10882]: SEND FAX: JOB 14 DEST 02314650137 COMMID 00000089 DEVICE
'/dev/ttyI0'
May 27 11:28:29.45: [10882]: MODEM set DTR OFF
May 27 11:28:29.45: [10882]: DELAY 75 ms
May 27 11:28:29.53: [10882]: MODEM set DTR ON
May 27 11:28:29.53: [10882]: DELAY 2600 ms
May 27 11:28:32.13: [10882]: MODEM set baud rate: 19200 baud, input flow XON/XOFF,
output flow XON/XOFF
May 27 11:28:32.13: [10882]: MODEM flush i/o
May 27 11:28:32.14: [10882]: <-- [4:ATZ\r]
May 27 11:28:32.14: [10882]: --> [2:OK]
May 27 11:28:32.14: [10882]: DELAY 3000 ms
May 27 11:28:35.14: [10882]: <-- [12:AT&E9698472\r]
May 27 11:28:35.15: [10882]: --> [11:AT&E9698472]
May 27 11:28:35.15: [10882]: --> [2:OK]
May 27 11:28:35.15: [10882]: <-- [5:ATE0\r]
May 27 11:28:35.16: [10882]: --> [4:ATE0]
May 27 11:28:35.16: [10882]: --> [2:OK]
May 27 11:28:35.16: [10882]: <-- [5:ATV1\r]
May 27 11:28:35.17: [10882]: --> [2:OK]
May 27 11:28:35.17: [10882]: <-- [5:ATQ0\r]
May 27 11:28:35.18: [10882]: --> [2:OK]
May 27 11:28:35.18: [10882]: <-- [7:ATS0=0\r]
May 27 11:28:35.19: [10882]: --> [2:OK]
May 27 11:28:35.19: [10882]: <-- [7:ATS8=2\r]
May 27 11:28:35.20: [10882]: --> [2:OK]
May 27 11:28:35.20: [10882]: <-- [8:ATS7=60\r]
May 27 11:28:35.21: [10882]: --> [2:OK]
May 27 11:28:35.21: [10882]: <-- [12:AT+FCLASS=1\r]
May 27 11:28:35.22: [10882]: --> [2:OK]
May 27 11:28:35.22: [10882]: <-- [5:ATM0\r]
May 27 11:28:35.23: [10882]: --> [2:OK]
May 27 11:28:35.23: [10882]: MODEM input buffering enabled
May 27 11:28:35.24: [10882]: <-- [12:AT+FCLASS=1\r]
May 27 11:28:35.34: [10882]: --> [2:OK]
May 27 11:28:35.34: [10882]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
May 27 11:28:35.47: [10882]: DIAL 02314650137
May 27 11:28:35.47: [10882]: <-- [16:ATDT02314650137\r]
May 27 11:28:47.94: [10882]: --> [7:CONNECT]
May 27 11:28:47.95: [10882]: MODEM input buffering disabled
May 27 11:28:49.21: [10882]: --> [2:OK]
May 27 11:28:49.21: [10882]: REMOTE NSF "00 00 56 55 55 00 8C 90 80 C1 02 5A"
May 27 11:28:49.21: [10882]: NSF remote fax equipment: Brother
May 27 11:28:49.21: [10882]: <-- [9:AT+FRH=3\r]
May 27 11:28:49.21: [10882]: --> [7:CONNECT]
May 27 11:28:49.91: [10882]: --> [2:OK]
May 27 11:28:49.91: [10882]: REMOTE CSI "+49 231 4650137"
May 27 11:28:49.91: [10882]: <-- [9:AT+FRH=3\r]
May 27 11:28:49.91: [10882]: --> [7:CONNECT]
May 27 11:28:50.35: [10882]: --> [2:OK]
May 27 11:28:50.35: [10882]: REMOTE best rate 14400 bit/s
May 27 11:28:50.35: [10882]: REMOTE max page width 1728 pixels in 215 mm
May 27 11:28:50.35: [10882]: REMOTE max unlimited page length
May 27 11:28:50.35: [10882]: REMOTE best vres 7.7 line/mm
May 27 11:28:50.35: [10882]: REMOTE best format 2-D MMR
May 27 11:28:50.35: [10882]: REMOTE supports T.30 Annex A, ECM
May 27 11:28:50.35: [10882]: REMOTE best 0 ms/scanline
May 27 11:28:50.35: [10882]: USE 14400 bit/s
May 27 11:28:50.35: [10882]: USE 0 ms/scanline
May 27 11:28:50.35: [10882]: SEND file "docq/doc14.cover;00"
May 27 11:28:50.35: [10882]: USE page width 1728 pixels in 215 mm
May 27 11:28:50.35: [10882]: USE unlimited page length
May 27 11:28:50.36: [10882]: USE 3.85 line/mm
May 27 11:28:50.36: [10882]: USE 1-D MR
May 27 11:28:50.36: [10882]: SEND training at v.17 14400 bit/s
May 27 11:28:50.36: [10882]: <-- [9:AT+FTH=3\r]
May 27 11:28:52.16: [10882]: --> [7:CONNECT]
May 27 11:28:52.20: [10882]: --> [7:CONNECT]
May 27 11:28:53.21: [10882]: --> [2:OK]
May 27 11:28:53.21: [10882]: <-- [9:AT+FTS=7\r]
May 27 11:28:53.22: [10882]: --> [5:ERROR]
May 27 11:28:53.22: [10882]: MODEM Command error
May 27 11:28:53.22: [10882]: <-- [9:AT+FTH=3\r]
May 27 11:28:54.85: [10882]: --> [7:CONNECT]
May 27 11:28:55.09: [10882]: --> [2:OK]
May 27 11:28:55.09: [10882]: MODEM input buffering enabled
May 27 11:28:55.09: [10882]: <-- [5:ATH0\r]
May 27 11:28:55.21: [10882]: --> [10:NO CARRIER]
May 27 11:28:55.21: [10882]: MODEM No carrier
May 27 11:28:55.21: [10882]: MODEM set DTR OFF
May 27 11:28:55.21: [10882]: SESSION END
--- End Message ---
signature.asc
Description: This is a digitally signed message part
