Hallo, habe hier einen dieser einfachen CamStick mit USB-Kabel, und wollte mal versuchen, unter Linux die Bilder auszulesen. Irgendwo habe ich mal gelesen, da� diese Camsticks als Wechselmedium gemountet werden k�nnen. Finde aber leider diese Quelle nicht mehr.
Ich lade also die usb-Module (modconf). Dmesg zeigt mir, da� sich da was tut: usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb.c: registered new driver audio audio.c: v1.0.0:USB Audio Class driver bluetooth.c: USB Bluetooth support registered usb.c: registered new driver bluetooth bluetooth.c: USB Bluetooth tty driver v0.12 usb.c: registered new driver dc2xx dc2xx.c: v1.0.0:USB Camera Driver for Kodak DC-2xx series cameras usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]> hid-core.c: USB HID support drivers Linux video capture interface: v1.00 usb.c: registered new driver ibmcam usb.c: registered new driver microtekX6 microtek.c: v0.4.3:Microtek Scanmaker X6 USB scanner driver mice: PS/2 mouse device common for all mice usb.c: registered new driver usblp printer.c: v0.8:USB Printer Device Class driver usb.c: registered new driver usbscanner scanner.c: 0.4.6:USB Scanner Driver uhci.c: USB Universal Host Controller Interface driver v1.1 PCI: Found IRQ 9 for device 00:1f.2 PCI: Setting latency timer of device 00:1f.2 to 64 uhci.c: USB UHCI at I/O 0xb400, IRQ 9 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. usb.c: registered new driver keyboard usbkbd.c: :USB HID Boot Protocol keyboard driver usb.c: registered new driver usb_mouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb-uhci.c: $Revision: 1.275 $ time 11:55:11 Apr 14 2002 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usb-uhci.c: $Revision: 1.275 $ time 11:55:11 Apr 14 2002 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: v1.275:USB Universal Host Controller Interface driver hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: USB device 2 (vend/prod 0x553/0x202) is not claimed by any active driver. usb.c: registered new driver stv680 stv680.c: [stv680_probe:1555] STV(i): STV0680 camera found. stv680.c: [stv680_probe:1583] STV(i): registered new video device: video0 stv680.c: [usb_stv680_init:1656] STV(i): usb camera driver version v0.24 registering Beim Aus-und Einstecken der Kamera (hotplug ist installiert) wird sie als STV0680 registriert. cat /proc/bus/usb/devices ergibt folgende Ausgabe: T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI-alt Root Hub S: SerialNumber=b400 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0553 ProdID=0202 Rev= 0.00 S: Manufacturer=STMicroelectronics S: Product=USB Dual-mode Camera C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 70mA I: If#= 0 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=00 Prot=00 Driver=stv680 I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=stv680 E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms in /etc/fstab steht: usbdevfs /proc/bus/usb usbdevfs defaults 0 0 usbview zeigt diesen CamStick als USB Dual-mode Camera an. Ja, und MAKEDEV usb input habe ich ausgef�hrt, sowie ein device /dev/video0 angelegt, Wie komme ich nun an die Bilder? Bin leider damit nicht weitergekommen. Vielen Dank und Gru� Uli -- Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)
