Hallo, ich versuche hier gerade, meinen neuen USB-Stick auf einem amd64-Debian zum Laufen zu kriegen. Und obwohl ich gerade über eine Stunde mit google befragen und probieren beschäftigt war, bin ich noch keinen Schritt weiter:
fdisk -l bringt nur Partitionen in /dev/hda (die Festplatte), dementsprechend komme ich auch bei meinen Versuchen, ihn zu mounten nur zu einem "dev/sda is not a valid block device". Also anscheinend wird er nichtmal erkannt. lsmod sagt: eiswiese:/home/wol# lsmod Module Size Used by usb_storage 43840 0 vfat 13376 0 fat 42592 1 vfat hotplug habe ich installiert, ich nehme an dass man da außer apt-get install hotplug nichts machen muß? Wenn ich den Stick einstecke, kommen weder in syslog noch in messages irgendwelche Meldungen :-( Die relevanten Teile von dmesg habe ich unten angehängt. Der Stick ist ein 1GB-Modell von Toshiba. Was mich etwas unruhig macht, ist folgender Passus im Handbuch: "Das Produkt arbeitet nicht mit anderen Betriebssystemen als Microsoft Windows". Ist das ernst zu nehmen, kann es also sein, dass ich gar keine Chance habe, ihn zum Laufen zu kriegen? Ich habe (noch) einen selbstkompilierten Kernel 2.6.9 - ist der zu alt? Wenn es irgendwie ginge, würde ich das installieren eines neuen Kernels gerne auf die Zeit nachdem dieser USB-Stick endlich läuft verschieben... Schonmal danke für Hilfe und nehmt mich bitte ins cc, da ich nicht auf der Liste bin. Wolfgang eiswiese:/home/wol# dmesg [...] hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21 ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc ports=8 ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024 ehci_hcd 0000:00:10.4: capability 0001 at 68 ehci_hcd 0000:00:10.4: irq 21, pci mem ffffff0000012400 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: reset command 080022 (park)=0 ithresh=8 Async period=1024 Reset HALT ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 ehci_hcd 0000:00:10.4: supports USB remote wakeup usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409 usb usb1: Product: VIA Technologies, Inc. USB 2.0 usb usb1: Manufacturer: Linux 2.6.9 ehci_hcd usb usb1: SerialNumber: 0000:00:10.4 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: ganged power switching hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: Single TT hub 1-0:1.0: TT requires at most 8 FS bit times hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 80 td 96 USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 21, io base 0000000000001800 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: detected 2 ports usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: default language 0x0409 usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller usb usb2: Manufacturer: Linux 2.6.9 uhci_hcd usb usb2: SerialNumber: 0000:00:10.0 usb usb2: hotplug usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 21, io base 0000000000001c00 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: detected 2 ports usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language 0x0409 usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) usb usb3: Manufacturer: Linux 2.6.9 uhci_hcd usb usb3: SerialNumber: 0000:00:10.1 usb usb3: hotplug usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.0: port 1 portsc 018a hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s uhci_hcd 0000:00:10.2: irq 21, io base 0000000000002000 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: detected 2 ports usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: default language 0x0409 usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) usb usb4: Manufacturer: Linux 2.6.9 uhci_hcd usb usb4: SerialNumber: 0000:00:10.2 usb usb4: hotplug usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: hotplug hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: no power switching (usb 1.0) hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: power on to power good time: 2ms hub 4-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.0: port 2 portsc 018a hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s uhci_hcd 0000:00:10.3: irq 21, io base 0000000000002400 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: detected 2 ports usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: default language 0x0409 usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) usb usb5: Manufacturer: Linux 2.6.9 uhci_hcd usb usb5: SerialNumber: 0000:00:10.3 usb usb5: hotplug usb usb5: adding 5-0:1.0 (config #1, interface 0) usb 5-0:1.0: hotplug hub 5-0:1.0: usb_probe_interface hub 5-0:1.0: usb_probe_interface - got id hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.1: port 1 portsc 008a hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.1: port 2 portsc 008a hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.2: port 1 portsc 008a hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s input: PS/2 Logitech Mouse on isa0060/serio1 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) ip_tables: (C) 2000-2002 Netfilter core team NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.2: port 2 portsc 008a hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 140k freed hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.3: port 1 portsc 018a hub 5-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s Losing some ticks... checking if CPU frequency changed. hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.3: port 2 portsc 008a hub 5-0:1.0: port 2, status 0100, change 0003, 12 Mb/s hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 warning: many lost ticks. Your time source seems to be instable or some driver is hogging interupts rip __do_softirq+0x48/0xb0 uhci_hcd 0000:00:10.0: suspend_hc uhci_hcd 0000:00:10.1: suspend_hc uhci_hcd 0000:00:10.2: suspend_hc uhci_hcd 0000:00:10.3: suspend_hc Adding 2097136k swap on /dev/hda5. Priority:-1 extents:1 EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on hda6, internal journal ide-floppy: hdd: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0 ide-floppy: hdd: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0 hdd: No disk in drive mtrr: no MTRR for f6000000,1000000 found ide-floppy: hdd: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0 ide-floppy: hdd: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0 hdd: No disk in drive Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. eiswiese:/home/wol#
