hi wie hast du die 3c920 ans laufen bekommen bzw. die realtec die bei mir beide auf dem board sind.Also, ich habe ein Leadtek Winfast Board. Die Netzwerkkarte habe ich installiert bekommen, indem ich die NVidia Treiber kompiliert habe. Dies ging mit gcc298 aber nicht, also habe ich in /usr/bin/ den gcc-3.0 nach gcc gelinkt und hatte Glück. Probier das auch mal mitm gcc 3.0, das müßte gehen.
Wenn der Treiber installiert ist, mußt Du nur modprobe nvnet starten.
Habe schon versucht die 3c90x zu kompilieren und mit dem nforce hatte ich auch klein glück! Das usb 2.0 und 1.1 läuft die geräte werden bei mir erkannt aber die maus gibt keinen pieps von sich obwohl alle Treiber geladen sind... also das selbe problem wie bei dir...Wie hast Du das usb bei Dir eingerichtet, bzw. welche Module hast Du kompiliert? Scheint, als ob der hid-Treiber nicht mitmacht.
MfG
Manu
Gruß Alexander
Manu wrote:
Hi @ All,
ich habe ein Debian laufen mit Kernel 2.4.20 mit Alan Cox Patch ac2. Alles
läuft, sogar die NVidia Netzwerkkarte und der Sound. Leider bekomme ich aber
meine Logitech USB-Maus nicht am USB-Controller zum laufen.
Ich habe folgendes im Kernel:
mousedev
usbcore
usb-ehci
usb-ohci
hid
lsmod gibt folgendes aus:
========================================================================= ===
Module Size Used by Not tainted
ehci-hcd 23264 0 (unused)
i810_audio 23360 3
ac97_codec 9856 0 [i810_audio]
usbmouse 1824 0 (unused)
hid 12928 0 (unused)
usb-ohci 18624 0 (unused)
mousedev 3904 0 (unused)
ircomm 7328 0 (unused)
irda 83756 0 [ircomm]
radeon 99160 0
ohci1394 16128 0 (unused)
keybdev 1728 0 (unused)
shaper 3228 0 (unused)
ospm_thermal 5840 0 (unused)
ieee1394 31080 0 [ohci1394]
ne2k-pci 5056 1
8390 5920 0 [ne2k-pci]
rtc 6108 0 (autoclean)
lspci -v gibt folgendes aus:
========================================================================= ===
00:00.0 Host bridge: nVidia Corporation: Unknown device 01e0 (rev a2)
Flags: bus master, 66Mhz, fast devsel, latency 0
Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [40] AGP version 2.0
Capabilities: [60] #08 [2001]
00:01.1 SMBus: nVidia Corporation: Unknown device 0064 (rev a2)
Subsystem: nVidia Corporation: Unknown device 0c11
Flags: 66Mhz, fast devsel
I/O ports at e400 [size=32]
Capabilities: [44] Power Management version 2
00:02.0 USB Controller: nVidia Corporation: Unknown device 0067 (rev a3)
(prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c11
Flags: 66Mhz, fast devsel
Memory at ef080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:02.1 USB Controller: nVidia Corporation: Unknown device 0067 (rev a3)
(prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c11
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 11
Memory at ef082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:02.2 USB Controller: nVidia Corporation: Unknown device 0068 (rev a3)
(prog-if 20)
Subsystem: nVidia Corporation: Unknown device 0c11
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 7
Memory at ef085000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
00:08.0 PCI bridge: nVidia Corporation: Unknown device 006c (rev a3)
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000bfff
00:0d.0 FireWire (IEEE 1394): nVidia Corporation: Unknown device 006e (rev
a3) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 05b2
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 5
Memory at ef083000 (32-bit, non-prefetchable) [size=2K]
Memory at ef084000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
00:1e.0 PCI bridge: nVidia Corporation: Unknown device 01e8 (rev a2)
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 32
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Beim einkompilieren der Module in den Kernel bekomme ich folgendes:
USB-EHCI: (aus Syslog)
========================================================================= ===
Dec 29 23:30:20 retro kernel: ehci-hcd.c: 2002-Sep-23 USB 2.0 'Enhanced'
Host Controller (EHCI) Driver
Dec 29 23:30:20 retro kernel: ehci-hcd.c: block sizes: qh 96 qtd 96 itd 128
sitd 64
Dec 29 23:30:20 retro kernel: PCI: Setting latency timer of device 00:02.2
to 64
Dec 29 23:30:20 retro kernel: hcd.c: ehci-hcd @ 00:02.2, PCI device
10de:0068 (nVidia Corporation)
Dec 29 23:30:20 retro kernel: hcd.c: irq 7, pci mem e0853000
Dec 29 23:30:20 retro kernel: usb.c: new USB bus registered, assigned bus
number 1
Dec 29 23:30:20 retro kernel: ehci-dbg.c: ehci_start hcs_params 0x102486
dbg=1 cc=2 pcc=4 !ppc ports=6
Dec 29 23:30:20 retro kernel: ehci-dbg.c: 00:02.2: ehci_start portroute 0 0
1 1 1 0
Dec 29 23:30:20 retro kernel: ehci-dbg.c: ehci_start extended capabilities
at pci a0
Dec 29 23:30:20 retro kernel: ehci-dbg.c: ehci_start hcc_params a086 caching
frame 256/512/1024 park
Dec 29 23:30:20 retro kernel: ehci-hcd.c: capability 0001 at a0
Dec 29 23:30:20 retro kernel: ehci-hcd.c: BIOS handoff not needed
Dec 29 23:30:20 retro kernel: ehci-hcd.c: reset command 080b02 park=3
ithresh=8 period=1024 Reset HALT
Dec 29 23:30:20 retro kernel: ehci-hcd.c: init command 010001 (park)=0
ithresh=1 period=1024 RUN
Dec 29 23:30:20 retro kernel: ehci-hcd.c: USB 2.0 support enabled, EHCI rev
1.00, ehci-hcd 2002-Sep-23
Dec 29 23:30:20 retro kernel: hcd.c: 00:02.2 root hub device address 1
Dec 29 23:30:20 retro kernel: usb.c: kmalloc IF dfa93940, numif 1
Dec 29 23:30:20 retro kernel: usb.c: new device strings: Mfr=3, Product=2,
SerialNumber=1
Dec 29 23:30:20 retro kernel: usb.c: USB device number 1 default language ID
0x0
Dec 29 23:30:20 retro kernel: Manufacturer: Linux 2.4.20-ac2 ehci-hcd
Dec 29 23:30:20 retro kernel: Product: PCI device 10de:0068 (nVidia
Corporation)
Dec 29 23:30:20 retro kernel: SerialNumber: 00:02.2
Dec 29 23:30:20 retro kernel: hub.c: USB hub found
Dec 29 23:30:20 retro kernel: hub.c: 6 ports detected
Dec 29 23:30:20 retro kernel: hub.c: standalone hub
Dec 29 23:30:20 retro kernel: hub.c: ganged power switching
Dec 29 23:30:20 retro kernel: hub.c: individual port over-current protection
Dec 29 23:30:20 retro kernel: hub.c: Single TT
Dec 29 23:30:20 retro kernel: hub.c: TT requires at most 8 FS bit times
Dec 29 23:30:20 retro kernel: hub.c: Port indicators are not supported
Dec 29 23:30:20 retro kernel: hub.c: power on to power good time: 0ms
Dec 29 23:30:20 retro kernel: hub.c: hub controller current requirement: 0mA
Dec 29 23:30:20 retro kernel: hub.c: port removable status: RRRRRR
Dec 29 23:30:20 retro kernel: hub.c: local power source is good
Dec 29 23:30:20 retro kernel: hub.c: no over-current condition exists
Dec 29 23:30:20 retro kernel: hub.c: enabling power on all ports
Dec 29 23:30:20 retro kernel: usb.c: hub driver claimed interface dfa93940
Dec 29 23:30:20 retro kernel: usb.c: kusbd: /sbin/hotplug add 1
Dec 29 23:30:20 retro kernel: usb.c: kusbd policy returned 0xfffffffe
Dec 29 23:30:20 retro kernel: ehci-hub.c: GetStatus port 1 status 001403
POWER sig=k CSC CONNECT
Dec 29 23:30:20 retro kernel: hub.c: port 1, portstatus 501, change 1, 480
Mb/s
Dec 29 23:30:20 retro kernel: hub.c: port 1 connection change
Dec 29 23:30:20 retro kernel: hub.c: port 1, portstatus 501, change 1, 480
Mb/s
Dec 29 23:30:20 retro kernel: hub.c: port 1, portstatus 501, change 0, 480
Mb/s
Dec 29 23:30:21 retro last message repeated 3 times
Dec 29 23:30:21 retro kernel: ehci-hub.c: 00:02.2 port 1 low speed, give to
companion
Dec 29 23:30:21 retro kernel: ehci-hub.c: GetStatus port 1 status 003402
POWER OWNER sig=k CSC
Dec 29 23:30:21 retro kernel: hub.c: port 1, portstatus 0, change 1, 12 Mb/s
Dec 29 23:30:21 retro kernel: ehci-hcd.c: 00:02.2: free_config devnum 0
Dec 29 23:30:21 retro kernel: hub.c: port 2, portstatus 100, change 0, 12
Mb/s
Dec 29 23:30:21 retro kernel: hub.c: port 3, portstatus 100, change 0, 12
Mb/s
Dec 29 23:30:21 retro kernel: hub.c: port 4, portstatus 100, change 0, 12
Mb/s
Dec 29 23:30:21 retro kernel: hub.c: port 5, portstatus 100, change 0, 12
Mb/s
Dec 29 23:30:21 retro kernel: hub.c: port 6, portstatus 100, change 0, 12
Mb/s
USB-OHCI: (aus syslog)
========================================================================= ===
Dec 29 23:33:30 retro kernel: PCI: No IRQ known for interrupt pin A of
device 00:02.0. Please try using pci=biosirq.
Dec 29 23:33:30 retro kernel: usb-ohci.c: found OHCI device with no IRQ
assigned. check BIOS settings!
Dec 29 23:33:30 retro kernel: PCI: Setting latency timer of device 00:02.1
to 64
Dec 29 23:33:30 retro kernel: usb-ohci.c: USB OHCI at membase 0xe08d0000,
IRQ 11
Dec 29 23:33:30 retro kernel: usb-ohci.c: usb-00:02.1, PCI device 10de:0067
(nVidia Corporation)
Dec 29 23:33:30 retro kernel: usb.c: new USB bus registered, assigned bus
number 2
Dec 29 23:33:30 retro kernel: usb.c: kmalloc IF da8b98c0, numif 1
Dec 29 23:33:30 retro kernel: usb.c: new device strings: Mfr=0, Product=2,
SerialNumber=1
Dec 29 23:33:30 retro kernel: usb.c: USB device number 1 default language ID
0x0
Dec 29 23:33:30 retro kernel: Product: USB OHCI Root Hub
Dec 29 23:33:30 retro kernel: SerialNumber: e08d0000
Dec 29 23:33:30 retro kernel: hub.c: USB hub found
Dec 29 23:33:30 retro kernel: hub.c: 3 ports detected
Dec 29 23:33:30 retro kernel: hub.c: standalone hub
Dec 29 23:33:30 retro kernel: hub.c: ganged power switching
Dec 29 23:33:30 retro kernel: hub.c: global over-current protection
Dec 29 23:33:30 retro kernel: hub.c: Port indicators are not supported
Dec 29 23:33:30 retro kernel: hub.c: power on to power good time: 2ms
Dec 29 23:33:30 retro kernel: hub.c: hub controller current requirement: 0mA
Dec 29 23:33:30 retro kernel: hub.c: port removable status: RRR
Dec 29 23:33:30 retro kernel: hub.c: local power source is good
Dec 29 23:33:30 retro kernel: hub.c: no over-current condition exists
Dec 29 23:33:30 retro kernel: hub.c: enabling power on all ports
Dec 29 23:33:30 retro kernel: usb.c: hub driver claimed interface da8b98c0
Dec 29 23:33:30 retro kernel: usb.c: kusbd: /sbin/hotplug add 1
Dec 29 23:33:30 retro kernel: usb.c: kusbd policy returned 0xfffffffe
Wenn ich die Maus ein- bzw. ausstecke ändert sich nichts, die LogDateien
bleiben leer, ein cat /dev/input/mice macht gar nichts.
Mir ist aufgefallen, dass der OHCI-Treiber keinen IRQ zugewiesen bekommen
hat.
Langsam nervt mich der NForce2, bitte helft mir.
MfG
Manu
--
Häufig gestellte Fragen und Antworten (FAQ): http://www.de.debian.org/debian-user-german-FAQ/
Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED]
mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)
