Hallo!
Ich habe, wie empfohlen, hylafax 4.1.5 kompiliert.
Der Fehler besteht scheinbar fort:
Your facsimile job to 02319698472 failed because:
Stop and wait failure (modem on hook); Giving up after 3 attempts to
send same page
---- Transcript of session follows ----
M�r 19 11:12:41.35: [25563]: SESSION BEGIN 00000023 492319698472
M�r 19 11:12:41.35: [25563]: HylaFAX (tm) Version 4.1.5
M�r 19 11:12:41.35: [25563]: SEND FAX: JOB 24 DEST 02319698472 COMMID
00000023 DEVICE '/dev/ttyI1'
M�r 19 11:12:41.35: [25563]: MODEM set DTR OFF
M�r 19 11:12:41.35: [25563]: DELAY 75 ms
M�r 19 11:12:41.44: [25563]: MODEM set DTR ON
M�r 19 11:12:41.44: [25563]: DELAY 2600 ms
M�r 19 11:12:44.03: [25563]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
M�r 19 11:12:44.03: [25563]: DELAY 10 ms
M�r 19 11:12:44.04: [25563]: MODEM flush i/o
M�r 19 11:12:44.04: [25563]: <-- [4:ATZ\r]
M�r 19 11:12:44.05: [25563]: --> [2:OK]
M�r 19 11:12:44.05: [25563]: DELAY 3000 ms
M�r 19 11:12:47.05: [25563]: <-- [11:AT&E243878\r]
M�r 19 11:12:47.06: [25563]: --> [10:AT&E243878]
M�r 19 11:12:47.06: [25563]: --> [2:OK]
M�r 19 11:12:47.06: [25563]: <-- [5:ATE0\r]
M�r 19 11:12:47.07: [25563]: --> [4:ATE0]
M�r 19 11:12:47.07: [25563]: --> [2:OK]
M�r 19 11:12:47.07: [25563]: <-- [5:ATV1\r]
M�r 19 11:12:47.08: [25563]: --> [2:OK]
M�r 19 11:12:47.08: [25563]: <-- [5:ATQ0\r]
M�r 19 11:12:47.09: [25563]: --> [2:OK]
M�r 19 11:12:47.09: [25563]: <-- [7:ATS0=0\r]
M�r 19 11:12:47.11: [25563]: --> [2:OK]
M�r 19 11:12:47.11: [25563]: <-- [7:ATS8=2\r]
M�r 19 11:12:47.11: [25563]: --> [2:OK]
M�r 19 11:12:47.11: [25563]: <-- [8:ATS7=60\r]
M�r 19 11:12:47.12: [25563]: --> [2:OK]
M�r 19 11:12:47.12: [25563]: <-- [12:AT+FCLASS=1\r]
M�r 19 11:12:47.13: [25563]: --> [2:OK]
M�r 19 11:12:47.13: [25563]: <-- [5:ATM0\r]
M�r 19 11:12:47.14: [25563]: --> [2:OK]
M�r 19 11:12:47.14: [25563]: MODEM input buffering enabled
M�r 19 11:12:47.14: [25563]: <-- [12:AT+FCLASS=1\r]
M�r 19 11:12:47.25: [25563]: --> [2:OK]
M�r 19 11:12:47.25: [25563]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
M�r 19 11:12:47.26: [25563]: DIAL 02319698472
M�r 19 11:12:47.26: [25563]: <-- [16:ATDT02319698472\r]
M�r 19 11:12:52.87: [25563]: --> [7:CONNECT]
M�r 19 11:12:52.87: [25563]: MODEM input buffering disabled
M�r 19 11:12:55.12: [25563]: --> [2:OK]
M�r 19 11:12:55.12: [25563]: REMOTE CSI "Hierweck"
M�r 19 11:12:55.12: [25563]: <-- [9:AT+FRH=3\r]
M�r 19 11:12:55.13: [25563]: --> [7:CONNECT]
M�r 19 11:12:55.48: [25563]: --> [2:OK]
M�r 19 11:12:55.48: [25563]: REMOTE best rate 14400 bit/s
M�r 19 11:12:55.48: [25563]: REMOTE max page width 2432 pixels in 303 mm
M�r 19 11:12:55.48: [25563]: REMOTE max unlimited page length
M�r 19 11:12:55.48: [25563]: REMOTE best vres 7.7 line/mm
M�r 19 11:12:55.48: [25563]: REMOTE best format 2-D MR
M�r 19 11:12:55.48: [25563]: REMOTE best 0 ms/scanline
M�r 19 11:12:55.48: [25563]: USE 14400 bit/s
M�r 19 11:12:55.48: [25563]: USE 0 ms/scanline
M�r 19 11:12:55.48: [25563]: SEND file "docq/doc24.cover;00"
M�r 19 11:12:55.48: [25563]: USE page width 1728 pixels in 215 mm
M�r 19 11:12:55.48: [25563]: USE unlimited page length
M�r 19 11:12:55.48: [25563]: USE 3.85 line/mm
M�r 19 11:12:55.48: [25563]: USE 1-D MR
M�r 19 11:12:55.49: [25563]: SEND training at v.17 14400 bit/s
M�r 19 11:12:55.49: [25563]: <-- [9:AT+FTH=3\r]
M�r 19 11:12:57.24: [25563]: --> [7:CONNECT]
M�r 19 11:12:57.26: [25563]: --> [7:CONNECT]
M�r 19 11:12:58.26: [25563]: --> [2:OK]
M�r 19 11:12:58.26: [25563]: <-- [9:AT+FTS=7\r]
M�r 19 11:12:58.27: [25563]: --> [5:ERROR]
M�r 19 11:12:58.27: [25563]: MODEM Command error
M�r 19 11:12:58.27: [25563]: SEND: Stop and wait failure (modem on
hook); Giving up after 3 attempts to send same page
"docq/doc24.cover;00", dirnum 0
M�r 19 11:12:58.27: [25563]: <-- [9:AT+FTH=3\r]
M�r 19 11:12:59.91: [25563]: --> [7:CONNECT]
M�r 19 11:13:00.15: [25563]: --> [2:OK]
M�r 19 11:13:00.16: [25563]: MODEM input buffering enabled
M�r 19 11:13:00.16: [25563]: <-- [5:ATH0\r]
M�r 19 11:13:00.26: [25563]: --> [10:NO CARRIER]
M�r 19 11:13:00.27: [25563]: MODEM No carrier
M�r 19 11:13:00.27: [25563]: MODEM set DTR OFF
M�r 19 11:13:00.27: [25563]: SESSION END
---- Unsent job status ----
Destination: 02319698472
JobID: 24
GroupID: 24
Sender: Michael Hierweck
Mailaddr: [EMAIL PROTECTED]
CommID: 00000023
Submitted From: localhost
Page Width: 209 (mm)
Page Length: 297 (mm)
Resolution: 98 (lpi)
Status: Stop and wait failure (modem on hook); Giving up after 3
attempts to send same page
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 3 (total phone calls placed)
Pages: 0 (pages transmitted)
TotPages: 2 (total pages to transmit)
Attempts: 3 (attempts to send current page)
Dirnum: 0 (directory of next page to send)
---- Documents submitted for transmission ----
The following documents were submitted for transmission and are
available on the server for reuse until they are automatically
purged when this job is removed. Documents may also be manually
removed using the faxrm command; consult faxrm(1) for information.
Filename Size Type
docq/doc24.cover 0 PostScript cover page
docq/doc47.ps 0 PostScript
Sicherheitshalber sende ich meine config.ttyI0 mit:
CountryCode: 49
AreaCode: 2304
FAXNumber: +49.2304.243878
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "Hierweck"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Von %%l|%c|Seite %%p von %%t"
PercentGoodLines: 80
MaxConsecutiveBadLines: 20
MaxRecvPages: 30
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect
fax/data
#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for
silence
ModemResetCmds: "AT&E243878" # stuff to do when modem
is reset
#ModemAnswerCmd: ATA # use this to answer
phone
#ModemNoFlowCmd: AT&K # disable flow control
cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command
results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook
(hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2
seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received
facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF &
response
Class1SendPPMDelay: 75 # 75ms delay before sending PPM
Class1SendTCFDelay: 75 # 75ms delay between sending DCS
& TCF
Class1TrainingRecovery: 1500 # 1.5sec delay after training
failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident
frames
Class1TCFMaxNonZero: 10 # max 10% of data may be
non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF
duration
#
#
#Class1SendEOPWaitCmd: <delay:90>
#Class1SendTCFWaitCmd: <delay:70>
#Class1SendPPMWaitCmd: <delay:70>
Muss ich doch den Kernelpatch einsetzen?
Die Sedlbauer AG hat scheinabr nicht einmal dokumentiert, was die dieser
Path eigentlich konkret bewirkt...
Viele Gr��e
Michael
--
Haeufig gestellte Fragen und Antworten (FAQ):
http://www.de.debian.org/debian-user-german-FAQ/
Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED]
mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)
