Am Die, 2003-06-10 um 23.29 schrieb Kim Neunert: > Hallo, > > Was ist denn da los? Mein Samba geht nicht mehr. ich habe ein Standard-Woody > und nach dem erfolglosen Installationsversuch von VMWare (glaube ich) geht > nicht mal mehr ein ping. Woran kann ich erkennen, wo der Fehler liegt? Beim > ping von dem woody-Rechner blinkt die Netzwerklampe nicht. Die Einstellungen > von ifconfig (s.u.) schaun aber gut aus: > > Hier das wichtigste von dmesg zu dem Thema: > > ------<-snip->------------------------------------------------------------------------------- > > NET4: Linux TCP/IP 1.0 for NET4.0 > IP Protocols: ICMP, UDP, TCP, IGMP > IP: routing cache hash table of 4096 buckets, 32Kbytes > TCP: Hash tables configured (established 32768 bind 32768) > Linux IP multicast router 0.06 plus PIM-SM > > [...] > > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > Unable to find swap-space signature > > [...] > > 8139too Fast Ethernet driver 0.9.24 > PCI: Found IRQ 10 for device 00:04.0 > eth0: RealTek RTL8139 Fast Ethernet at 0xd88c2f00, 00:50:ba:d5:73:e9, IRQ 10 > eth0: Identified 8139 chip type 'RTL-8139B' > PCI: Found IRQ 5 for device 00:0f.0 > PCI: Sharing IRQ 5 with 00:07.2 > eth1: RealTek RTL8139 Fast Ethernet at 0xd88c4e00, 00:30:84:78:77:aa, IRQ 5 > eth1: Identified 8139 chip type 'RTL-8139C' > > [...] > > eth1: Setting half-duplex based on auto-negotiated partner ability 0000. > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > CSLIP: code copyright 1989 Regents of the University of California > PPP generic driver version 2.4.1 > Fire GL built-in AGP-support > Based on agpgart interface v0.99 (c) Jeff Hartmann > agpgart: Maximum main memory to use for agp memory: 321M > agpgart: Detected AMD 751 (Irongate) chipset > agpgart: AGP aperture is 64M @ 0xe8000000 > [fglr200] AGP detected, AgpState = 0x0f000203 (hardware caps) > [fglr200] AGP enabled, AgpCommand = 0x0f000302 (selected caps) > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > eth1: Setting half-duplex based on auto-negotiated partner ability 0000. > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Tx queue start entry 4283 dirty entry 4279. > eth0: Tx descriptor 0 is 00002000. > eth0: Tx descriptor 1 is 00002000. > eth0: Tx descriptor 2 is 00002000. > eth0: Tx descriptor 3 is 00002000. (queue head) > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > eth1: Setting half-duplex based on auto-negotiated partner ability 0000. > NETDEV WATCHDOG: eth0: transmit timed out > eth0: Tx queue start entry 203 dirty entry 199. > eth0: Tx descriptor 0 is 00002000. > eth0: Tx descriptor 1 is 00002000. > eth0: Tx descriptor 2 is 00002000. > eth0: Tx descriptor 3 is 00002000. (queue head) > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > eth1: Setting half-duplex based on auto-negotiated partner ability 0000. > > > eth1: Setting half-duplex based on auto-negotiated partner ability 0000. > eth0: Setting half-duplex based on auto-negotiated partner ability 0000. > > > > > > ------<-snip->------------------------------------------------------------------------------- > > jetzt noch ifconfig > > ------<-snip->------------------------------------------------------------------------------- > > > eth0 Protokoll:Ethernet Hardware Adresse 00:50:BA:D5:73:E9 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:8426 errors:0 dropped:0 overruns:0 frame:0 > TX packets:8414 errors:0 dropped:0 overruns:0 carrier:0 > Kollisionen:5 Sendewarteschlangenl�nge:100 > RX bytes:5269869 (5.0 MiB) TX bytes:1068177 (1.0 MiB) > Interrupt:10 Basisadresse:0x2f00 > > eth1 Protokoll:Ethernet Hardware Adresse 00:30:84:78:77:AA > inet Adresse:192.168.0.1 Bcast:192.168.0.255 Maske:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:99 errors:0 dropped:0 overruns:0 frame:0 > TX packets:55 errors:0 dropped:0 overruns:0 carrier:0 > Kollisionen:0 Sendewarteschlangenl�nge:100 > RX bytes:12278 (11.9 KiB) TX bytes:9435 (9.2 KiB) > Interrupt:5 Basisadresse:0x4e00 > > lo Protokoll:Lokale Schleife > inet Adresse:127.0.0.1 Maske:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:13641 errors:0 dropped:0 overruns:0 frame:0 > TX packets:13641 errors:0 dropped:0 overruns:0 carrier:0 > Kollisionen:0 Sendewarteschlangenl�nge:0 > RX bytes:4239664 (4.0 MiB) TX bytes:4239664 (4.0 MiB) > > ppp0 Protokoll:Punkt-zu-Punkt Verbindung > inet Adresse:217.233.69.210 P-z-P:217.5.98.170 > Maske:255.255.255.255 > UP PUNKTZUPUNKT RUNNING NOARP MULTICAST MTU:1492 Metric:1 > RX packets:1787 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1782 errors:0 dropped:0 overruns:0 carrier:0 > Kollisionen:0 Sendewarteschlangenl�nge:3 > RX bytes:1601740 (1.5 MiB) TX bytes:205614 (200.7 KiB) > > ------<-snip->------------------------------------------------------------------------------- > > W�r cool, wenn da jemand einen Wink hat. > > Gru� > > Kim >
Was sagt "route -n" und "cat /etc/resolv.conf"? Was kannst Du nicht anpingen? Eine lokale IP-Adresse oder einen FQDN? Sebastian -- Haeufig gestellte Fragen und Antworten (FAQ): http://www.de.debian.org/debian-user-german-FAQ/ Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)
