Hallo, ich versuche aus einigen wav-Dateien eine Audio-CDs zu brennen. Dazu verwende ich den Befehl: cdrecord -v dev=ATAPI:0,0,0 -pad *.wav Aber den Brennvorgang scheitert jedes Mal. Hier die Ausgabe auf den Konsole:
cdrecord: No write mode specified. cdrecord: Asuming -tao mode. cdrecord: Future versions of cdrecord may have different drive dependent defaults. cdrecord: Continuing in 5 seconds... Cdrecord-Clone 2.01a34 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling NOTE: this version of cdrecord is an inofficial (modified) release of cdrecord and thus may have bugs that are not present in the original version. Please send bug reports and support requests to <[EMAIL PROTECTED]>. The original author should not be bothered with problems of this version. TOC Type: 0 = CD-DA scsidev: 'ATAPI:0,0,0' devname: 'ATAPI' scsibus: 0 target: 0 lun: 0 Warning: Using ATA Packet interface. Warning: The related Linux kernel interface code seems to be unmaintained. Warning: There is absolutely NO DMA, operations thus are slow. Using libscg version 'schily-0.8'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'TOSHIBA ' Identifikation : 'DVD-ROM SD-R6012' Revision : '1034' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x000A Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A (current) Profile: 0x0011 Profile: 0x0013 Profile: 0x0014 cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code. cdrecord: See /usr/share/doc/cdrecord/README.DVD.Debian for details on DVD support. Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R Drive buf size : 1723392 = 1683 KB FIFO size : 4194304 = 4096 KB Track 01: audio 3 MB (00:22.33) no preemp pad Track 02: audio 42 MB (04:10.93) no preemp pad Track 03: audio 30 MB (03:00.89) no preemp pad Track 04: audio 31 MB (03:09.07) no preemp pad Total size: 109 MB (10:49.26) = 48695 sectors Lout start: 109 MB (10:51/20) = 48695 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 6 Reference speed: 0 Is not unrestricted Is erasable ATIP start of lead in: -11078 (97:34/22) ATIP start of lead out: 359849 (79:59/74) Disk type: Phase change Manuf. index: 11 Manufacturer: Mitsubishi Chemical Corporation Blocks total: 359849 Blocks current: 359849 Blocks remaining: 311154 Starting to write CD/DVD at speed 4 in real TAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF. Performing OPC... Starting new track at sector: 0 Track 01: 0 of 3 MB written.cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 00 F3 00 00 1B 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 0C 00 00 00 00 00 Sense Key: 0x3 Medium Error, Segment 0 Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 19.946s timeout 40s write track data: error after 571536 bytes cdrecord: A write error occured. cdrecord: Please properly read the error message above. Writing time: 26.558s Average write speed 24.5x. Fixating... cdrecord: Input/output error. close track/session: scsi sendcmd: no error CDB: 5B 00 02 00 00 00 00 00 00 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 0C 00 00 00 00 00 Sense Key: 0x3 Medium Error, Segment 0 Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 19.902s timeout 480s cmd finished after 19.902s timeout 480s cdrecord: Cannot fixate disk. Fixating time: 19.904s cdrecord: fifo had 73 puts and 10 gets. cdrecord: fifo was 0 times empty and 1 times full, min fill was 87%. Das Brennen von mp3s mit mp3burn produziert ähnliche Fehler. Das Brennen von Daten-CDs, falls es sich nur um eine Session handelt, klappt einwandfrei. Multisessions sind nicht möglich, da mir cdrecord berichtet, dass es den Sektor zum Fortfahren auf der CD nicht findet. Ich fahre Debian Sarge mit Kernel 2.6.8.1 ohne SCSI-Emulation. Vielen Dank für jeden Tipp. Gruß Christian -- Haeufig gestellte Fragen und Antworten (FAQ): http://www.de.debian.org/debian-user-german-FAQ/ Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)