Hola, estoy intentando hacer funcionar mi webcam, una Genius Express V2. Utilizo Debian Sid con kernel 2.6.7 compilado por m�.
He buscado por google en muchas p�ginas para ver que soporte ten�a que activar en el kernel. Todos las entradas USB detectan si enchufo la camara, lo compruebo haciendo "usbview", pero me pone "dispositivo desconocido", o sea, que no tengo el driver adecuado, supongo. Si hago "lsusb" me sale: Bus 004 Device 010: ID 0458:7004 KYE Systems Corp. (Mouse Systems) Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 001: ID 0000:0000 Y si hago dmesg, lo referente a USB es lo siguiente: ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc ports=6 ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024 ehci_hcd 0000:00:10.3: capability 0001 at 68 ehci_hcd 0000:00:10.3: irq 10, pci mem d0b36000 ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 ehci_hcd 0000:00:10.3: supports USB remote wakeup usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409 usb usb1: Product: VIA Technologies, Inc. USB 2.0 usb usb1: Manufacturer: Linux 2.6.7-ck6 ehci_hcd usb usb1: SerialNumber: 0000:00:10.3 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: ganged power switching hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: Single TT hub 1-0:1.0: TT requires at most 8 FS bit times hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 USB Universal Host Controller Interface driver v2.2 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 10, io base 0000d400 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: detected 2 ports usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: default language 0x0409 usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller usb usb2: Manufacturer: Linux 2.6.7-ck6 uhci_hcd usb usb2: SerialNumber: 0000:00:10.0 usb usb2: hotplug usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 11, io base 0000d800 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: detected 2 ports usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language 0x0409 usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) usb usb3: Manufacturer: Linux 2.6.7-ck6 uhci_hcd usb usb3: SerialNumber: 0000:00:10.1 usb usb3: hotplug usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.0: port 1 portsc 008a hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s uhci_hcd 0000:00:10.0: port 2 portsc 008a hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s uhci_hcd 0000:00:10.2: irq 11, io base 0000dc00 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: detected 2 ports usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: default language 0x0409 usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) usb usb4: Manufacturer: Linux 2.6.7-ck6 uhci_hcd usb usb4: SerialNumber: 0000:00:10.2 usb usb4: hotplug usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: hotplug hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: no power switching (usb 1.0) hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: power on to power good time: 2ms hub 4-0:1.0: local power source is good Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver uhci_hcd 0000:00:10.1: port 1 portsc 008a hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s uhci_hcd 0000:00:10.1: port 2 portsc 008a hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s mice: PS/2 mouse device common for all mice input: PC Speaker serio: i8042 AUX port at 0x60,0x64 irq 12 uhci_hcd 0000:00:10.0: port 1 portsc 0088 hub 2-0:1.0: port 1 enable change, status 00000100 uhci_hcd 0000:00:10.0: port 2 portsc 0088 hub 2-0:1.0: port 2 enable change, status 00000100 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 uhci_hcd 0000:00:10.2: port 1 portsc 008a hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s uhci_hcd 0000:00:10.2: port 2 portsc 008a hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s input: AT Translated Set 2 keyboard on isa0060/serio0 uhci_hcd 0000:00:10.1: port 1 portsc 0088 hub 3-0:1.0: port 1 enable change, status 00000100 uhci_hcd 0000:00:10.1: port 2 portsc 0088 hub 3-0:1.0: port 2 enable change, status 00000100 uhci_hcd 0000:00:10.2: port 1 portsc 0088 hub 4-0:1.0: port 1 enable change, status 00000100 uhci_hcd 0000:00:10.2: port 2 portsc 0088 hub 4-0:1.0: port 2 enable change, status 00000100 uhci_hcd 0000:00:10.0: suspend_hc uhci_hcd 0000:00:10.1: suspend_hc uhci_hcd 0000:00:10.2: suspend_hc ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501 hub 1-0:1.0: port 6 not reset yet, waiting 50ms ehci_hcd 0000:00:10.3: port 6 full speed --> companion ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j CONNECT uhci_hcd 0000:00:10.2: wakeup_hc uhci_hcd 0000:00:10.2: port 2 portsc 0093 hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s hub 4-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101 usb 4-2: new full speed USB device using address 2 usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 4-2: hotplug usb 4-2: adding 4-2:1.0 (config #1, interface 0) usb 4-2:1.0: hotplug uhci_hcd 0000:00:10.2: port 2 portsc 008a hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s usb 4-2: USB disconnect, address 2 usb 4-2: usb_disable_device nuking all URBs usb 4-2: unregistering interface 4-2:1.0 usb 4-2:1.0: hotplug usb 4-2: unregistering device usb 4-2: hotplug ehci_hcd 0000:00:10.3: GetStatus port 6 status 001002 POWER sig=se0 CSC hub 1-0:1.0: port 6, status 0100, change 0001, 12 Mb/s uhci_hcd 0000:00:10.2: port 2 portsc 0088 hub 4-0:1.0: port 2 enable change, status 00000100 uhci_hcd 0000:00:10.2: suspend_hc ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501 hub 1-0:1.0: port 6 not reset yet, waiting 50ms ehci_hcd 0000:00:10.3: port 6 full speed --> companion ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j CONNECT uhci_hcd 0000:00:10.2: wakeup_hc uhci_hcd 0000:00:10.2: port 2 portsc 0093 hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s hub 4-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101 usb 4-2: new full speed USB device using address 3 usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 4-2: hotplug usb 4-2: adding 4-2:1.0 (config #1, interface 0) usb 4-2:1.0: hotplug ehci_hcd 0000:00:10.3: GetStatus port 6 status 001002 POWER sig=se0 CSC hub 1-0:1.0: port 6, status 0100, change 0001, 12 Mb/s uhci_hcd 0000:00:10.2: port 2 portsc 008a hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s usb 4-2: USB disconnect, address 3 usb 4-2: usb_disable_device nuking all URBs usb 4-2: unregistering interface 4-2:1.0 usb 4-2:1.0: hotplug usb 4-2: unregistering device usb 4-2: hotplug uhci_hcd 0000:00:10.2: port 2 portsc 0088 hub 4-0:1.0: port 2 enable change, status 00000100 uhci_hcd 0000:00:10.2: suspend_hc ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501 hub 1-0:1.0: port 6 not reset yet, waiting 50ms ehci_hcd 0000:00:10.3: port 6 full speed --> companion ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j CONNECT uhci_hcd 0000:00:10.2: wakeup_hc uhci_hcd 0000:00:10.2: port 2 portsc 0093 hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s hub 4-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101 usb 4-2: new full speed USB device using address 4 usb 4-2: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 4-2: hotplug usb 4-2: adding 4-2:1.0 (config #1, interface 0) usb 4-2:1.0: hotplug Si hago "dmesg | grep video" o "dmesg | grep cam" no sale nada. Doy por hecho que he activado m�s cosas de las necesarias en el kernel, pero bueno. Tengo instalado el paquete "v4l-conf". El caso es que he ido a la p�gina: http://www.qbik.ch/usb/devices/showdev.php?id=1975 en la que se dan unos drivers para mi webcam, los spca50x. En estos drivers me informan de que necesito "v4l stuff" en el kernel tanto para 2.4 como para 2.6, pero no encuentro dicha opci�n en mi kernel 2.6.7. Entonces hago la instalaci�n del driver supuestamente sin problemas. Tambi�n me indican que tras la instalaci�n, al hacer "lsmod, spca50x should be load with videodev", pero yo hago "lsmod" y no aparece nada al respecto. En definitiva no logro que me detecte la camara. �Alguien sabe qu� me falta? Muchas gracias.
