En el network interfaces no puedes ponerle a las dos tarjetas de red el mismo gateway, haz una prueba comentando un gateway.
Hay una cosa que no entiendo bien, y es que tienes dos tarjetas de red con el mismo rango ip, para qué ?, si no es mucho preguntar. Yo pondría solo una y la otra en otro rango, para lo que haga falta. 2007/11/14, Mario Ybañez <[EMAIL PROTECTED]>: > > hola: > > quiero instalar debian testing en mi pc > pero no hay forma de hacer andar la red > > (en ubuntu, fedora y mandriva anda todo ok) > > aqui mando los datos por si alguien me puede ayudar > > mi pc tiene 2 placas de red onboard > es un palaca asus striker extreme > cuyas ip son eth0 192.168.1.2 y eth1 192.168.1.3 > > el cable teoricamente lo tengo conectado a eth0 > > ademas tengo un server que me hace la conexion cuya placa tiene como ip > 192.168.1.1 > > ======================================== > > > > salida de > > dmesg | grep eth > > forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. > forcedeth: using HIGHDMA > eth0: forcedeth.c: subsystem: 01043:cb84 bound to 0000:00:11.0 > forcedeth: using HIGHDMA > eth1: forcedeth.c: subsystem: 01043:cb84 bound to 0000:00:12.0 > eth1: no link during initialization. > eth1: no link during initialization. > eth1: no link during initialization. > ADDRCONF(NETDEV_UP): eth1: link is not ready > eth0: no IPv6 routers present > eth0: no IPv6 routers present > eth1: no link during initialization. > ADDRCONF(NETDEV_UP): eth1: link is not ready > eth1: no link during initialization. > ADDRCONF(NETDEV_UP): eth1: link is not ready > eth1: no link during initialization. > ADDRCONF(NETDEV_UP): eth1: link is not ready > eth1: no link during initialization. > ADDRCONF(NETDEV_UP): eth1: link is not ready > eth0: no IPv6 routers present > > //////////// comentario ////////////////////////////// > de todo esto supongo que el cable de red esta > conecatdo en eth0 > dado que no tengo conexion a internet no piedo instalar el ethtool > > > > > baiscamente el problema es que al terminarla configuracion de la red > y quiero hacer un ping a internet o a la placa del server que hace la > conexion me dice > > > > Destination Host Unreachable > > > > ahi van los datos > > > > ========================================================= > > archivo /etc/networks/interface > > # This file describes the network interfaces available on your system > # and how to activate them. For more information, see interfaces(5). > > # The loopback network interface > auto lo > iface lo inet loopback > > # The primary network interface > allow-hotplug eth0 > > iface eth1 inet static > address 192.168.1.3 > netmask 255.255.255.0 > gateway 192.168.1.1 > > auto eth1 > > iface eth0 inet static > address 192.168.1.2 > netmask 255.255.255.0 > gateway 192.168.1.1 > > ///////////////comentario//////////////////// > > tambien probe en agragarle al final > auto eth0 ... y sigue el problema > > > ========================================================== > salida de > > ifconfig > > > eth0 Link encap:Ethernet HWaddr 00:1A:92:9B:EB:E3 > inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: fe80::21a:92ff:fe9b:ebe3/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:87 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:10116 (9.8 KiB) > Interrupt:17 Base address:0x6000 > > eth1 Link encap:Ethernet HWaddr 00:1A:92:C2:B6:54 > inet addr: 192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:18 Base address:0x4000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:131 errors:0 dropped:0 overruns:0 frame:0 > TX packets:131 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:12574 (12.2 KiB) TX bytes:12574 (12.2 KiB) > > ================================================================ > > salida de > > route > > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use > Iface > localnet * 255.255.255.0 U 0 0 0 > eth0 > localnet * 255.255.255.0 U 0 0 0 > eth1 > default 192.168.1.1 0.0.0.0 UG 0 0 0 > eth0 > > //////////comentario//////// > como el cable esta conectado en eth0 , segun el comentario > hecho mas arriba .... entonces los datos deben salir por eth0 > compare con el route de ubuntu que anda bien y esta igual que este > > ============================================================================ > > ping 192.168.1.1 que es la ip del server > > PING 192.168.1.1 ( 192.168.1.1) 56(84) bytes of data. > From 192.168.1.2 icmp_seq=2 Destination Host Unreachable > From 192.168.1.2 icmp_seq=3 Destination Host Unreachable > From 192.168.1.2 icmp_seq=4 Destination Host Unreachable > From 192.168.1.2 icmp_seq=6 Destination Host Unreachable > From 192.168.1.2 icmp_seq=7 Destination Host Unreachable > From 192.168.1.2 icmp_seq=8 Destination Host Unreachable > > --- 192.168.1.1 ping statistics --- > 9 packets transmitted, 0 received, +6 errors, 100% packet loss, time > 7999ms > , pipe 3 > > ========================================================= > > //////////////ping a la ambas palcas de mi pc////////////// > > PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data. > 64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.011 ms > 64 bytes from 192.168.1.2: icmp_seq=2 ttl=64 time=0.008 ms > 64 bytes from 192.168.1.2: icmp_seq=3 ttl=64 time=0.006 ms > > --- 192.168.1.2 ping statistics --- > 3 packets transmitted, 3 received, 0% packet loss, time 1999ms > rtt min/avg/max/mdev = 0.006/0.008/0.011/0.003 ms > > > > PING 192.168.1.3 ( 192.168.1.3) 56(84) bytes of data. > 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.012 ms > 64 bytes from 192.168.1.3 : icmp_seq=2 ttl=64 time=0.008 ms > 64 bytes from 192.168.1.3: icmp_seq=3 ttl=64 time=0.007 ms > 64 bytes from 192.168.1.3: icmp_seq=4 ttl=64 time=0.006 ms > > --- 192.168.1.3 ping statistics --- > 4 packets transmitted, 4 received, 0% packet loss, time 2997ms > rtt min/avg/max/mdev = 0.006/0.008/0.012/0.003 ms > > ================================================================ > > saludos > > > -- > Mario S. Ybañez > Linux User # 398682 > > -- ... "On Debian" ....
