�ste poblema mismo me ocurria a mi en un servidor que mont�. Tenia dos
discos de 60 en un ATARAID tipo 1 y �ste error me lo daba siempre al
arrancar cuando tenia los discos metidos en cajetines extraibles.
Conect�ndolos directamente a la manguera no daba ese error.
El servidor corria Potato (ahora Woody) con un kernel 2.4.14 y la
controladora RAID �s una Konwel con chip hpt570 (pero ya te digo que no
era fallo de la controladora si no de los cajetines). Ahora el servidor
est� funcionando con los cajetines conectados a pleno rendimiento y no
da ning�n problema.
El lun, 14-10-2002 a las 22:54, Manwe Sulimo escribi�:
> He comprado un disco duro. Lo he particionado con la cd de la woody, he
> instalado el sistema base y he actualizado a testing. Mi sorpresa cuando al
> copiar el directorio home de otro disco me daba una tasa de 100MB/MINUTO!!
> Luego al usar mi sistema wme di cuenta de que las X y las aplicaciones son
> inestables. El error que me suelen dar los programas es el siguiente:
>
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hdb: DMA disabled
>
> este error tambien me lo da en el arranque del kernel que he compilado aunque
> no el kernel que me instal� la woody. Aqui pongo los dos mensajes del
> arranque de los dos kernels. Ayuda por favor.
>
> Linux version 2.4.18monolith ([EMAIL PROTECTED]) (gcc version 2.95.4 20011002
> (Debian prerelease)) #1 jue oct 10 03:24:22 CEST 2002
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
> BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
> BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> On node 0 totalpages: 131056
> zone(0): 4096 pages.
> zone(1): 126960 pages.
> zone(2): 0 pages.
> Kernel command line: BOOT_IMAGE=Linux ro root=305
> Initializing CPU#0
> Detected 1541.235 MHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 3073.63 BogoMIPS
> Memory: 513436k/524224k available (1350k kernel code, 10404k reserved, 410k
> data, 192k init, 0k highmem)
> Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
> Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
> Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
> CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After vendor init, caps: 0383fbff c1c3fbff 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
> CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
> CPU: AMD Athlon(tm) XP 1800+ stepping 02
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> PCI: PCI BIOS revision 2.10 entry at 0xfb5f0, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Unknown bridge resource 0: assuming transparent
> PCI: Using IRQ router VIA [1106/0686] at 00:07.0
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> Starting kswapd
> Journalled Block Device driver loaded
> NTFS driver v1.1.22 [Flags: R/O]
> Detected PS/2 Mouse Port.
> pty: 256 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI
> enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> block: 128 slots per queue, batch=32
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
> ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
> hda: ST340016A, ATA DISK drive
> hdb: HL-DT-ST CD-ROM GCR-8520B, ATAPI CD/DVD-ROM drive
> hdc: ST38420A, ATA DISK drive
> hdd: MATSHITA CD-R CW-7582, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
> hdc: 16841664 sectors (8623 MB) w/512KiB Cache, CHS=16708/16/63, UDMA(33)
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> hdc: [PTBL] [1048/255/63] hdc1 hdc2 hdc3 hdc4
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> PPP generic driver version 2.4.1
> PPP Deflate Compression module registered
> PPP BSD Compression module registered
> Linux agpgart interface v0.99 (c) Jeff Hartmann
> agpgart: Maximum main memory to use for agp memory: 439M
> agpgart: unsupported bridge
> agpgart: no supported devices found.
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> Vendor: HL-DT-ST Model: CD-ROM GCR-8520B Rev: 1.00
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: MATSHITA Model: CD-R CW-7582 Rev: 1.05
> Type: CD-ROM ANSI SCSI revision: 02
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
> sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.12
> sr1: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
> Via 686a audio driver 1.9.1
> PCI: Found IRQ 10 for device 00:07.5
> ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
> via82cxxx: Codec rate locked at 48Khz
> via82cxxx: board #1 at 0xE000, IRQ 10
> es1371: version v0.30 time 03:25:22 Oct 10 2002
> usb.c: registered new driver hub
> uhci.c: USB Universal Host Controller Interface driver v1.1
> PCI: Found IRQ 12 for device 00:07.2
> PCI: Sharing IRQ 12 with 00:07.3
> uhci.c: USB UHCI at I/O 0xd800, IRQ 12
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 2 ports detected
> PCI: Found IRQ 12 for device 00:07.3
> PCI: Sharing IRQ 12 with 00:07.2
> uhci.c: USB UHCI at I/O 0xdc00, IRQ 12
> usb.c: new USB bus registered, assigned bus number 2
> hub.c: USB hub found
> hub.c: 2 ports detected
> Initializing USB Mass Storage driver...
> usb.c: registered new driver usb-storage
> USB Mass Storage support registered.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 4096 buckets, 32Kbytes
> TCP: Hash tables configured (established 32768 bind 32768)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 192k freed
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
> hdb: DMA disabled
> ide0: reset: success
> Adding Swap: 996020k swap-space (priority -1)
> nvidia: loading NVIDIA Linux x86 NVdriver Kernel Module 1.0-3123 Tue Aug 27
> 15:56:48 PDT 2002
> NVRM: AGPGART: unable to retrieve symbol table
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide1(22,4), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
>
>
>
>
>
> Linux version 2.2.20-idepci ([EMAIL PROTECTED]) (gcc version 2.7.2.3) #1 Sat
> Apr 20 12:45:19 EST 2002
> BIOS-provided physical RAM map:
> BIOS-e820: 000a0000 @ 00000000 (usable)
> BIOS-e820: 1fef0000 @ 00100000 (usable)
> Detected 1541261 kHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 3073.63 BogoMIPS
> Memory: 517148k/524224k available (1164k kernel code, 408k reserved, 5432k
> data, 72k init)
> Dentry hash table entries: 65536 (order 7, 512k)
> Buffer cache hash table entries: 524288 (order 9, 2048k)
> Page cache hash table entries: 131072 (order 7, 512k)
> CPU: L1 I Cache: 64K L1 D Cache: 64K
> CPU: L2 Cache: 256K
> CPU: AMD Athlon(tm) XP 1800+ stepping 02
> Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
> Checking 'hlt' instruction... OK.
> Checking for popad bug... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
> PCI: PCI BIOS revision 2.10 entry at 0xfb5f0
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Enabling I/O for device 00:00
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> TCP: Hash tables configured (ehash 524288 bhash 65536)
> Starting kswapd v 1.5
> vga16fb: initializing
> vga16fb: mapped to 0xc00a0000
> Console: switching to colour frame buffer device 80x30
> fb0: VGA16 VGA frame buffer device
> Detected PS/2 Mouse Port.
> Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> pty: 256 Unix98 ptys configured
> RAM disk driver initialized: 16 RAM disks of 4096K size
> loop: registered device at major 7
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
> hda: ST340016A, ATA DISK drive
> hdb: HL-DT-ST CD-ROM GCR-8520B, ATAPI CDROM drive
> hdc: ST38420A, ATA DISK drive
> hdd: MATSHITA CD-R CW-7582, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: ST340016A, 38166MB w/2048kB Cache, CHS=4865/255/63
> hdc: ST38420A, 8223MB w/512kB Cache, CHS=16708/16/63
> hdb: ATAPI 52X CD-ROM drive, 128kB Cache
> Uniform CD-ROM driver Revision: 3.11
> hdd: ATAPI 8X CD-ROM CD-R drive, 1024kB Cache
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> 3c59x.c 18Feb01 Donald Becker and others
> http://www.scyld.com/network/vortex.html
> pcnet32.c: PCI bios is present, checking for devices...
> via-rhine.c:v1.08b-LK1.0.1 12/14/2000 Written by Donald Becker
> http://www.scyld.com/network/via-rhine.html
> Partition check:
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
> hdc: [PTBL] [1048/255/63] hdc1 hdc2 hdc3 hdc4
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
> apm: disabled on user request.
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 72k freed
> Adding Swap: 996020k swap-space (priority -1)
> NTFS version 000607
> CSLIP: code copyright 1989 Regents of the University of California
> SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256).
> SLIP linefill/keepalive option.
>
>
> --
> To UNSUBSCRIBE, email to [EMAIL PROTECTED]
> with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
>
--
