Hola! Tengo debian, y he instalado fedora. En la instalacion elegi que no me modificar el gestor de arranque lilo que utilizaba con debian, para asi despues modificarlo y que pudiera a�adir fedora.
Mis particiones estan asi: > Device Boot Start End Blocks Id System > /dev/hda1 1 62 497983+ 82 Linux swap > /dev/hda2 63 5099 40459702+ 83 Linux > /dev/hda3 * 5100 7297 17655435 83 Linux /hda2 es debian, y hda3 es fedora core 2. Cuando ejecuto lilo me da el siguiente error, que no encuentra la imagen de fedora: > Boot image: /vmlinuz -> boot/vmlinuz-2.6.4 > Added Linux * > > Boot image: /vmlinuz.old -> boot/vmlinuz-2.6.3 > Added LinuxOLD > > Boot image: /boot/vmlinuz-2.6.5-1.358 > Fatal: open /boot/vmlinuz-2.6.5-1.358: No such file or directory La configuracion de lilo es: > # cat /etc/lilo.conf > # /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)', > # --------------- `install-mbr(8)', `/usr/share/doc/lilo/', > # and `/usr/share/doc/mbr/'. > > # +---------------------------------------------------------------+ > # | !! Reminder !! | > # | | > # | Don't forget to run `lilo' after you make changes to this | > # | conffile, `/boot/bootmess.txt', or install a new kernel. The | > # | computer will most likely fail to boot if a kernel-image | > # | post-install script or you don't remember to run `lilo'. | > # | | > # +---------------------------------------------------------------+ > > # Support LBA for large hard disks. > # > lba32 > > # Overrides the default mapping between harddisk names and the BIOS' > # harddisk order. Use with caution. > #disk=/dev/hde > # bios=0x81 > > #disk=/dev/sda > # bios=0x80 > > # Specifies the boot device. This is where Lilo installs its boot > # block. It can be either a partition, or the raw device, in which > # case it installs in the MBR, and will overwrite the current MBR. > # > boot=/dev/hda > > # Specifies the device that should be mounted as root. (`/') > # > root=/dev/hda2 > > # Enable map compaction: > # Tries to merge read requests for adjacent sectors into a single > # read request. This drastically reduces load time and keeps the > # map smaller. Using `compact' is especially recommended when > # booting from a floppy disk. It is disabled here by default > # because it doesn't always work. > # > # compact > > # Installs the specified file as the new boot sector > # You have the choice between: bmp, compat, menu and text > # Look in /boot/ and in lilo.conf(5) manpage for details > # > install=/boot/boot-menu.b > > # Specifies the location of the map file > # > map=/boot/map > > # You can set a password here, and uncomment the `restricted' lines > # in the image definitions below to make it so that a password must > # be typed to boot anything but a default configuration. If a > # command line is given, other than one specified by an `append' > # statement in `lilo.conf', the password will be required, but a > # standard default boot will not require one. > # > # This will, for instance, prevent anyone with access to the > # console from booting with something like `Linux init=/bin/sh', > # and thus becoming `root' without proper authorization. > # > # Note that if you really need this type of security, you will > # likely also want to use `install-mbr' to reconfigure the MBR > # program, as well as set up your BIOS to disallow booting from > # removable disk or CD-ROM, then put a password on getting into the > # BIOS configuration as well. Please RTFM `install-mbr(8)'. > # > # password=tatercounter2000 > > # Specifies the number of deciseconds (0.1 seconds) LILO should > # wait before booting the first image. > # > delay=20 > > # You can put a customized boot message up if you like. If you use > # `prompt', and this computer may need to reboot unattended, you > # must specify a `timeout', or it will sit there forever waiting > # for a keypress. `single-key' goes with the `alias' lines in the > # `image' configurations below. eg: You can press `1' to boot > # `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'. > # > # message=/boot/bootmess.txt > prompt > timeout=150 > # prompt > # single-key > # delay=100 > # timeout=100 > > # Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>) > # > # vga=ask > # vga=9 > #vga=normal > vga=4 > > # Kernel command line options that apply to all installed images go > # here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in > # the Linux kernel `Documentation' directory. > # > # append="" > append = "hda=7297,255,63" > > # Boot up Linux by default. > # > default=Linux > > image=/vmlinuz > label=Linux > read-only > # restricted > # alias=1 > > image=/vmlinuz.old > label=LinuxOLD > read-only > optional > # restricted > # alias=2 > > root=/dev/hda3 > image=/boot/vmlinuz-2.6.5-1.358 > label="Fedora Core 2" > initrd=/boot/initrd-2.6.5-1.358.img > map=/boot/System.map-2.6.5-1.358 > read-only > > # If you have another OS on this machine to boot, you can uncomment the > # following lines, changing the device name on the `other' line to > # where your other OS' partition is. > # > # other=/dev/hda4 > # label=HURD > # restricted > # alias=3 > other=/dev/hda1 > label="Other(hda1)" He montado la particion /dev/hda3 de fedora en mi /mnt de debian para ver que los archivos son correctos, y el resultado es: # ls /mnt/boot/ config-2.6.5-1.358 grub initrd-2.6.5-1.358.img System.map-2.6.5-1.358 vmlinuz-2.6.5-1.358 �Cual puede ser el error por el que no me encuentra la imagen de fedora y no me aparece en lilo? Por cierto, el gestor de arranque lilo lo tengo en el MBR. Un saludo! Gerardo
