si qq peut avoir la volont� de regarder ce qui suit peut �tre trouveras til
mes deux problemes :
1 cdrom sur deux accesssible
floppy inaccessible
quand essai de lecture du contenu du cdrom1, acces disquette et message
"impossible de lire ..."
Le cd rom et le floppy sont verrouill�s, et inaccessibles. J'y perd mon latin,
j'ai essaye de les demonter dans drakeconf, de changer le type, toujours
rien.....
Merci et d�sol� d'envoyer un si grand message, que la ML ne se f�che pas,
quand j'aurais mieux compris tout cela je crois que j'essayerai de rendre la
pareille aux nouveaux arrivants.
Voila le d�but du fichier obtenu avec DMESG
Linux version 2.2.14-15mdk ([EMAIL PROTECTED]) (gcc version 2.95.2
19991024 (release)) #1 Tue Jan 4 22:24:20 CET 2000
relocating initrd image:
initrd_start:0xc0faa000 initrd_end:0xc0fff934
mem_start:0xc026d000 mem_end:0xc40ff000
initrd_size:0x00055934 dest:0xc40a9000
Detected 267276977 Hz processor.
ide_setup: hdc=ide-scsi
Console: colour VGA+ 80x25
Calibrating delay loop... 266.24 BogoMIPS
Memory: 63692k/66556k available (1092k kernel code, 416k reserved, 948k data,
64k init, 0k bigmem)
Dentry hash table entries: 262144 (order 9, 2048k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Klamath) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xfda28
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS not found.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 91366U4, ATA DISK drive
hdb: FUJITSU MPD3173AT, ATA DISK drive
hdc: Hewlett-Packard CD-Writer Plus 8100, ATAPI CDROM drive
hdd: Pioneer DVD-ROM ATAPIModel DVD-103S 011, ATAPI CDROM drive
ide2: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 91366U4, 13029MB w/2048kB Cache, CHS=1661/255/63
hdb: FUJITSU MPD3173AT, 16500MB w/512kB Cache, CHS=2103/255/63
hdd: ATAPI 0X DVD-ROM drive, 512kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 588.645 MB/sec
p5_mmx : 615.696 MB/sec
8regs : 477.774 MB/sec
32regs : 251.841 MB/sec
using fastest function: p5_mmx (615.696 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1
hdb: hdb1
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 4/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Warning - detected auto-termination
(scsi0) Please verify driver detected settings are correct.
(scsi0) If not, then please properly set the device termination
(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi0) during machine bootup.
(scsi0) Cables present (Int-50 NO, Int-68 YES, Ext-68 NO)
(scsi0) Downloading sequencer code... 413 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.21/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 8.
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17850000 [8715 MB] [8.7 GB]
sda: sda1 sda2 < sda5 sda6 sda7 >
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 64k freed
Adding Swap: 240932k swap-space (priority -1)
Creative SBLive! detected
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 2 hosts.
Vendor: HP Model: CD-Writer+ 8100 Rev: 1.0g
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
