Bonjour Je n'arrive pas � utiliser xawtv ou kwintv suite � l'impossibilit� de configuer ma carte TV (Miro PC TV). Pour information, j'ai lu et appliqu� les infos du site lea-linux.org ainsi que celle sur le site http://www.medsyn.fr/perso/g.delafond/survie.htm et sur le magazine planet linux hors s�rie N�1 de mai 1999 Mais, rien n'y fait ; dans le meilleur des cas, xawtv se lance, mais la certaines touches raccourcis ne sont pas actives, ni les options des menus ; idem pour presque pour kwintv (clic sur menu ne fait rien)... De plus, certaines modifications du fichier modules.conf ont pour effet apr�s lancement d'un des 2 programmes tv pr�cit�s de planter linux ! Le bouton reset de mon pc semble la seule solution de d�bloquer la situation. Je suis s�r que certains vont sourire de mes difficult�s mais je me permets tout de m�me de poster ce message car j'ai r�alis� ce genre d'op�rations avec succ�s sur des versions pr�c�dentes de mandrake (6.1 et 7.0). Aussi, si quelqu'un pouvait m'aider, je lui serais tr�s reconnaissant et � toutes fins utiles, je joins en PJ l'affichage g�n�r� par la commmande dmesg ainsi que mon fichier modules.conf. Vraiment d�sol� de "polluer" la liste par un si long e-mail... j'esp�re que la correction de ce probl�me (post�e sur la liste) pourra profiter � beaucoup d'utilisateurs d�butants de linux qui comme moi "gal�rent" pour configuer et utiliser une carte tv sous linux... Merci d'avance... *** Richard TUQUET LABURRE WEB : http://www.RTLinfo.com ICQ : 87226610 ***
alias net-pf-4 ipx alias char-major-107 3dfx pre-install pcmcia_core /etc/rc.d/init.d/pcmcia start alias usb-interface usb-uhci alias parport_lowlevel parport_pc alias block-major-11 scsi_hostadapter pre-install plip modprobe parport_pc ; echo 7 > /proc/parport/0/irq alias scsi_hostadapter dc395x_trm alias char-major-81-0 videodev alias char-major-81 bttv # TV ajout pre-install bttv modprobe -k tuner options tuner type=3 options bttv�� radio=0 card=1 # post-install awe_wave /bin/sfxload /etc/midi/GU11-ROM.SF2 options sb io=0x240 irq=9 dma=1 dma16=7 mpu_io=0x300 alias sound-slot-0 sb options sound dmabuf=1 options opl3 io=0x388 alias midi0 awe_wave post-install midi0 /bin/sfxload /etc/midi/GU11-ROM.SF2 options sound-slot-0 io=0x240 irq=9 dma=1 dma16=7
Linux version 2.2.17-21mdk ([EMAIL PROTECTED]) (gcc version 2.95.3 19991030 (prerelease)) #1 Thu Oct 5 13:16:08 CEST 2000 ... Linux video capture interface: v1.00 i2c-core.o: i2c core module i2c-algo-bit.o: i2c bit algorithm module i2c-core.o: driver i2c TV tuner driver registered. bttv: driver version 0.7.35 loaded bttv: using 2 buffers with 2080k (4160k total) for capture bttv: Bt8xx card found (0). bttv0: Brooktree Bt848 (rev 18) bus: 0, devfn: 104, irq: 5, memory: 0xe9001000. tuner: chip found @ 0x60 bttv0: i2c attach [Philips SECAM] i2c-core.o: client [Philips SECAM] registered to adapter [bt848 #0](pos. 0). i2c-core.o: adapter bt848 #0 registered as adapter 0. bttv0: i2c: checking for eeprom @ 0xa0... not found bttv0: i2c: checking for eeprom @ 0xae... not found bttv0: model: BT848A( *** UNKNOWN *** ) [autodetected] bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: i2c: checking for TDA8425 @ 0x82... not found bttv0: i2c: checking for TDA985x @ 0xb6... not found bttv0: i2c: checking for TDA9875 @ 0xb0... not found PnP: Calling quirk for 01:00 PnP: Calling quirk for 01:02 isapnp: Card 'Creative SB AWE64 PnP' isapnp: 1 Plug & Play card detected total Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996 SB 4.16 detected OK (240) usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.232 $ time 13:21:03 Oct 5 2000 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: Intel USB controller: setting latency timer to 0 usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 usb.c: USB new device connect, assigned device number 1 hub.c: USB hub found hub.c: 2 ports detected usb.c: USB new device connect, assigned device number 2 usb.c: This device is not recognized by any installed USB driver. parport0: PC-style at 0x3bc (0x7bc) [SPP,ECP,ECPPS2] parport0: detected irq 7; use procfs to enable interrupt-driven operation. parport_probe: failed parport0: no IEEE-1284 device present. lp0: using parport0 (polling). bttv0: i2c detach [Philips SECAM] i2c-core.o: client [Philips SECAM] unregistered. i2c-core.o: adapter unregistered: bt848 #0 i2c-core.o: driver unregistered: i2c TV tuner driver i2c-core.o: driver i2c TV tuner driver registered. bttv: driver version 0.7.35 loaded bttv: using 2 buffers with 2080k (4160k total) for capture bttv: Bt8xx card found (0). bttv0: Brooktree Bt848 (rev 18) bus: 0, devfn: 104, irq: 5, memory: 0xe9001000. PCI: Enabling bus mastering for device 00:68 tuner: chip found @ 0x60 bttv0: i2c attach [Philips SECAM] i2c-core.o: client [Philips SECAM] registered to adapter [bt848 #0](pos. 0). i2c-core.o: adapter bt848 #0 registered as adapter 0. bttv0: i2c: checking for eeprom @ 0xa0... not found bttv0: i2c: checking for eeprom @ 0xae... not found bttv0: model: BT848A( *** UNKNOWN *** ) [autodetected] bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: i2c: checking for TDA8425 @ 0x82... not found bttv0: i2c: checking for TDA985x @ 0xb6... not found bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c detach [Philips SECAM] i2c-core.o: client [Philips SECAM] unregistered. i2c-core.o: adapter unregistered: bt848 #0
