I've installed
linux-image-3.13.0-39-generic and linux-image-extra-3.13.0-39-generic,
$ sudo apt-get install linux-image-3.13.0-39-generic
linux-image-extra-3.13.0-39-generic
Czytanie list pakietów... Gotowe
Budowanie drzewa zależności
Odczyt informacji o stanie... Gotowe
linux-image-3.13.0-39-generic jest już w najnowszej wersji.
linux-image-extra-3.13.0-39-generic jest już w najnowszej wersji.
0 aktualizowanych, 0 nowo instalowanych, 0 usuwanych i 16 nieaktualizowanych.
3.13.0-40-generic
but I dont know how can I switch my 3 X I have 3 X Dell UltraSharp
U2414H LED IPS connected form one Display Port in serial
graphic_card_out-1monitor_DisplayPort_in/1monitor_DisplayPort_out-
2monitor_DisplayPort_in/2monitor_DisplayPort_out-3monitor_DisplayPort_in
I have still same picture on each monitor.
In setup Ubuntu window I see only one monitor detected.
What should I do nest to have fill MultiPort environment ?
$ uname -r
3.13.0-40-generic
$ lspci | grep VGA
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI]
Pitcairn PRO [Radeon HD 7850]
$ xrandr
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 16384 x 16384
DFP1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis)
527mm x 296mm
1920x1080 60.0*+ 50.0 59.9 60.1 50.0 24.0 60.0
1600x1200 60.0
1776x1000 50.0 59.9 50.0 24.0 60.0
1680x1050 60.0 50.0 59.9 24.0
1400x1050 60.0 50.0 24.0
1600x900 50.0 60.0 24.0
1280x1024 50.0 75.0 60.0 24.0
1440x900 50.0 60.0 24.0
1280x960 50.0 75.0 60.0 24.0
1152x864 50.0 59.9 75.0 24.0
1280x768 50.0 75.0 60.0 24.0
1280x720 60.0 50.0 24.0 59.9
1024x768 50.0 75.0 24.0 60.0
1152x648 50.0 59.9
800x600 50.0 24.0 75.0 60.3
720x480 50.0 24.0 60.0 59.9
640x480 50.0 24.0 75.0 59.9
DFP2 disconnected (normal left inverted right x axis y axis)
DFP3 disconnected (normal left inverted right x axis y axis)
DFP4 disconnected (normal left inverted right x axis y axis)
DFP5 disconnected (normal left inverted right x axis y axis)
DFP6 disconnected (normal left inverted right x axis y axis)
DFP7 disconnected (normal left inverted right x axis y axis)
CRT1 disconnected (normal left inverted right x axis y axis)
$ sudo lspci -vv
...
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI]
Pitcairn PRO [Radeon HD 7850] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device 042c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at f7e00000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at e000 [size=256]
Expansion ROM at f7e40000 [disabled] [size=128K]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1
unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit
Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee003f8 Data: 0000
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010 <?>
Capabilities: [150 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [270 v1] #19
Capabilities: [2b0 v1] Address Translation Service (ATS)
ATSCap: Invalidate Queue Depth: 00
ATSCtl: Enable-, Smallest Translation Unit: 00
Capabilities: [2c0 v1] #13
Capabilities: [2d0 v1] #1b
Kernel driver in use: fglrx_pci
--
You received this bug notification because you are a member of Desktop
Packages, which is subscribed to xserver-xorg-video-intel in Ubuntu.
https://bugs.launchpad.net/bugs/1104230
Title:
DisplayPort 1.2 MST support is missing in the Intel driver
Status in X.org xf86-video-intel:
Unknown
Status in xserver-xorg-video-intel package in Ubuntu:
Confirmed
Bug description:
SRU Justification:
Impact: Many users expect the possibility to use the DP1.2 MST feature which
enables them to use a number of different display setups: daisy-chaining
DP1.2 displays, some 4K displays appearing as 2 separate displays, 3D
displays.
This however is not supported in Ubuntu stable kernel.
Fix: A series of 18 cherry-picks from v3.17 kernel backported to v3.16 by
the original author of the feature: David Airlie.
Regression Potential: These patches were merged upstream in v3.17 without any
reported regressions.
Original description:
I have two recent DisplayPort monitors, both supporting the 1.2
version of the standard and one containing an MST hub (DELL 2913WM).
I have an Intel Haswell based NUC connected over mini-displayport to
the display containing the hub, then the second display is plugged in
that one over DisplayPort.
DisplayPort 1.2 is enabled on the display containing the hub and the
second display lights up fine but just works as a clone of the first
display, without ever showing up in xrandr, dmesg or any other useful
logs I could find.
My understanding of MST is that the second display should show up as
DP2 on my laptop so I can configure it as I would any other display.
UPDATE: Updated the bug report after it was pointed out that the
original test hardware, a Lenovo x230 isn't DP 1.2 capable. The same
test on hardware also fails, due to missing support for MST in the
driver.
To manage notifications about this bug go to:
https://bugs.launchpad.net/xserver-xorg-video-intel/+bug/1104230/+subscriptions
--
Mailing list: https://launchpad.net/~desktop-packages
Post to : desktop-packages@lists.launchpad.net
Unsubscribe : https://launchpad.net/~desktop-packages
More help : https://help.launchpad.net/ListHelp
