> -----Original Message-----
> From: Shally Verma [mailto:[email protected]]
> Sent: Monday, July 23, 2018 3:51 PM
> To: De Lara Guarch, Pablo <[email protected]>
> Cc: [email protected]; [email protected];
> [email protected]; Sunila Sahu <[email protected]>;
> Sunila Sahu <[email protected]>; Ashish Gupta
> <[email protected]>
> Subject: [PATCH v4 4/5] compress/zlib: support burst enqueue/dequeue
>
> From: Sunila Sahu <[email protected]>
>
> Signed-off-by: Sunila Sahu <[email protected]>
> Signed-off-by: Shally Verma <[email protected]>
> Signed-off-by: Ashish Gupta <[email protected]>
> ---
> drivers/compress/zlib/zlib_pmd.c | 255
> ++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 254 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/compress/zlib/zlib_pmd.c
> b/drivers/compress/zlib/zlib_pmd.c
> index 47bc73d..dc1e230 100644
> --- a/drivers/compress/zlib/zlib_pmd.c
> +++ b/drivers/compress/zlib/zlib_pmd.c
> @@ -7,7 +7,214 @@
>
> #include "zlib_pmd_private.h"
>
> -/** Parse comp xform and set private xform/stream parameters */
> +/** Compute next mbuf in the list, assign data buffer and length,
> + * returns 0 if mbuf is NULL
> + */
> +#define COMPUTE_BUF(mbuf, data, len) \
> + ((mbuf = mbuf->next) ? \
> + (data = rte_pktmbuf_mtod(mbuf, uint8_t *)), \
> + (len = rte_pktmbuf_data_len(mbuf)) : 0)
> +
> +static void
> +process_zlib_deflate(struct rte_comp_op *op, z_stream *strm) {
...
> + /* Update z_stream with the inputs provided by application */
> + strm->next_in = rte_pktmbuf_mtod_offset(mbuf_src, uint8_t *,
> + op->src.offset);
This is assuming that src buffer is a linear buffer or that offset won't be
large enough to cross boundaries between segments.
If an SGL is passed and offset is bigger than the first segment, next_in should
point at a different segment, with the remaining part of the offset in that
segment
(look at ISA-L SGL patch: http://patches.dpdk.org/patch/43283/). Same applies
to avail_in, next_out and avail_out.
> +
> + strm->avail_in = rte_pktmbuf_data_len(mbuf_src) - op->src.offset;
> +
> + strm->next_out = rte_pktmbuf_mtod_offset(mbuf_dst, uint8_t *,
> + op->dst.offset);
> +
> + strm->avail_out = rte_pktmbuf_data_len(mbuf_dst) - op->dst.offset;
> +
...
> + strm->next_in = rte_pktmbuf_mtod_offset(mbuf_src, uint8_t *,
> + op->src.offset);
> +
> + strm->avail_in = rte_pktmbuf_data_len(mbuf_src) - op->src.offset;
> +
> + strm->next_out = rte_pktmbuf_mtod_offset(mbuf_dst, uint8_t *,
> + op->dst.offset);
> +
> + strm->avail_out = rte_pktmbuf_data_len(mbuf_dst) - op->dst.offset;
Same comments as above (compression).
...
> +static inline int
> +process_zlib_op(struct zlib_qp *qp, struct rte_comp_op *op) {
> + struct zlib_stream *stream;
> + struct zlib_priv_xform *private_xform;
> +
> + if ((op->op_type == RTE_COMP_OP_STATEFUL) ||
> + (op->src.offset > rte_pktmbuf_data_len(op->m_src)) ||
> + (op->dst.offset > rte_pktmbuf_data_len(op->m_dst))) {
Since m_src and m_dst could be SGLs, pkt_len should be checked, instead of
data_len (which would be only for single segment).
Also, you should check the length too, in case of source buffers (src.offset +
src.length > m_src->pkt_len).
Lastly, the two lines after the first if line should have double indentation to
distinguish clearly against the body of the if.
If line is too long, consider storing the length of the buffers in variables.
> + op->status = RTE_COMP_OP_STATUS_INVALID_ARGS;
> + ZLIB_PMD_ERR("Invalid source or destination buffers or "
> + "invalid Operation requested\n");
