Hi Thomas,
This issue has already been fixed, see:
http://mails.dpdk.org/archives/dev/2020-October/185921.html
It has been integrated, Long was able to test it and confirm it fixed
this issue.
On 20/10/20 00:36 +0200, Thomas Monjalon wrote:
> Fixing Gaetan's address
>
> 20/10/2020 00:33, Thomas Monjalon:
> > Gaetan, Matan,
> > Please could you check?
> >
> >
> > 25/09/2020 22:30, Long Li:
> > > HI Matan,
> > >
> > > While troubleshooting a failure in DPDK on device removal when VF device
> > > briefly disappears and comes back, I notice the failsafe driver is trying
> > > repeatedly to start a sub device (after this sub device has been
> > > successfully configured, but later hot removed from the kernel). This is
> > > due to repeated alarms calling fs_dev_start(). I trace into this commit:
> > >
> > > ae80146 net/failsafe: fix removed device handling
> > >
> > > The implementation of fs_err() is interesting:
> > >
> > > +fs_err(struct sub_device *sdev, int err)
> > > +{
> > > + /* A device removal shouldn't be reported as an error. */
> > > + if (sdev->remove == 1 || err == -EIO)
> > > + return rte_errno = 0;
> > > + return err;
> > > +}
> > >
> > > If I change this function to:
> > > @@ -497,7 +497,7 @@ int failsafe_eth_new_event_callback(uint16_t port_id
> > > fs_err(struct sub_device *sdev, int err)
> > > {
> > > /* A device removal shouldn't be reported as an error. */
> > > - if (sdev->remove == 1 || err == -EIO)
> > > + if (sdev->remove == 1 && err == -EIO)
> > > return rte_errno = 0;
> > > return err;
> > > }
> > >
> > > The hung is going away. I don't know the reason why we use a || in the
> > > if(). If a call to rte_eth_dev_start() returning EIO (as the case in
> > > fs_dev_start), the best choice would be bail out and fail this sub device.
> > >
> > > Can you please take a look?
> > >
> > > Thanks,
> > > Long
> > >
> > > ________________________________
> > > From: Matan Azrad <ma...@nvidia.com>
> > > Sent: Tuesday, September 15, 2020 12:00 AM
> > > To: Long Li <lon...@microsoft.com>; Stephen Hemminger
> > > <step...@networkplumber.org>
> > > Cc: ma...@mellanox.com <ma...@mellanox.com>; gr...@u246.net
> > > <gr...@u246.net>; dev@dpdk.org <dev@dpdk.org>; Raslan Darawsheh
> > > <rasl...@nvidia.com>
> > > Subject: RE: [dpdk-dev] [PATCH] net/vdev_netvsc: handle removal of
> > > associated pci device
> > >
> > > Hi Li
> > >
> > > From: Long Li <lon...@microsoft.com>
> > > > >Subject: Re: [dpdk-dev] [PATCH] net/vdev_netvsc: handle removal of
> > > > >associated pci device
> > > > >
> > > > >Hi Stephen
> > > > >
> > > > >From: Stephen Hemminger:
> > > > >> On Sun, 6 Sep 2020 12:38:18 +0000
> > > > >> Matan Azrad <ma...@nvidia.com> wrote:
> > > > >>
> > > > >> > Hi Stephen
> > > > >> >
> > > > >> > From: Stephen Hemminger:
> > > > >> > > The vdev_netvsc was not detecting when the associated PCI device
> > > > >> > > (SRIOV) was removed. Because of that it would keep feeding the
> > > > >> > > same
> > > > >> > > (removed) device to failsafe PMD which would then unsuccessfully
> > > > >> > > try and probe for it.
> > > > >> > >
> > > > >> > > Change to use a mark/sweep method to detect that PCI device was
> > > > >> > > removed, and also only tell failsafe about new PCI devices.
> > > > >> > > Vdev_netvsc does not have to keep stuffing the pipe with the same
> > > > >> > > already existing PCI device.
> > > > >> >
> > > > >> > As I know, the vdev_netvsc driver doesn't call to failsafe if the
> > > > >> > PCI device is
> > > > >> not detected by the readlink command(considered as removed)...
> > > > >> > Am I missing something?
> > > > >>
> > > > >> The original code is broken because ctx_yield is not cleared, it
> > > > >> keeps sending the same value.
> > > > >
> > > > >Looking on the code again, It looks like ctx->yield has no effect on
> > > > >the next pipe write, It is just used for log.
> > > > >
> > > > >After the PCI interface matching to the netvsc interface, the pipe
> > > > >write is triggered only if the readlink commands success to see the
> > > > >plugged-in PCI
> > > > >device:
> > > > >readlink /sys/class/net/[iface]/device/subsystem shows "pci"
> > > > >readlink /sys/class/net/[iface]/device shows the pci device ID.
> > > > >
> > > > >So, the assumption is when the above readlink failed on the interface
> > > > >the device is removed(plugged-out) and the fd write will not happen.
> > > > >
> > > > >The code will continue to retry probe again and again until success
> > > > >only for plugged-in pci device matched the netvsc device.
> > > >
> > > > Hi Matan,
> > > >
> > > > The original code keeps writing to pipe even it's the same PCI device.
> > >
> > > Yes, the vdev_netvsc writes any plugged-in device to the associated
> > > netvsc device fd.
> > >
> > > > The
> > > > new code writes to pipe for a new device, only once. See the following
> > > > code:
> > > >
> > > > + /* Skip if this is same device already sent to failsafe */
> > > > + if (strcmp(addr, ctx->yield) == 0)
> > > > + return 0;
> > > >
> > >
> > > I understand you want to optimize the pipe writing to be written only
> > > after plugged-in hot event.
> > >
> > > The current solution suffers from race: the PCI device may be plugged-out
> > > and plugged-in in short time shorter than the driver alarm delay, then
> > > the PCI device plugged-in detection will lost.
> > >
> > > My suggestion:
> > > Add validation to the plugged-in device probing state and that it is
> > > owned by failsafe(using ownership API) - don't write the pipe if so.
> > >
> > > Matan
> > >
> > >
> > >
> > > > This patch also saves lots of CPU since it no longer writes to pipe all
> > > > the time.
> > > > You are correct about the code will continue to probe on a new PCI
> > > > device.
> > > > But someone has to do it to handle hot-add.
> > > >
> > > > Thanks,
> > > > Long
> > > >
> > > >
> > > > >
> > > > >> It looks like device removal and add was never tested.
> > > > >
> > > > >This is basic test we have to test plug-in plug-out and it passed every
> > > > >day in the last years.
> > > > >
> > > > >Maybe something new and special in your setup?
> > > > >
> > > > >> If you test removal you will see that vdev_netvsc:
> > > > >> 1. Sends same PCI device repeatedly to failsafe (every alarm call)
> > > > >> This is harmless, but useless.
> > > > >> 2. When device is removed, keeps doing #1
> > >
> >
> >
> >
>
>
>
>
>
--
Gaëtan
