Hello,
Should have said this is the FRDM-K64F board, freedom-k64f configuration.
Kind regards
Stewart
On 14/02/2021 09:37, nu...@charnell.plus.com wrote:
Hello,
I would like to setup a Kinetis k64f as a USB host to communicate with
a USB serial device. As there is not a configuration for USB host with
the k64f I thought I would start by configuring the k64f as a USB
device, but have not been able to produce a working (visible USB
device on K64 USB interface) setup yet.
I wonder if anyone has used the USB interface on the Kinetis k64f, or
the Kinetis k28, or might have some tips on how to debug?
The k64f has two modes of USB clocking, derived from PLL clock or
IRC48 clock sync'd to incoming USB data. I started by using clocking
derived from PLL.
I have modified a number of source files based on the Kinetis k28,
which has a configuration for usbnsh:
nuttx/boards/arm/kinetis/freedom-k64f/include/board.h based on
freedom-k28 board.h. Modified to set MCG Frequency (PLLOUT) to 96 MHz
and included settings for USB clocks.
nuttx/boards/arm/kinetis/freedom-k64f/src/k64_usbdev.c. Added DP
Pullup in non-OTG device mode, based on k28_usbdev.c, and
k64_usbinitialize routine. Pull-up functioning (measured with
multimeter).
nuttx/boards/arm/kinetis/freedom-k64f/src/k64_bringup.c - Added call
to k64_usbinitialize & CONFIG_PL2303
nsh is working over SDA USB interface (the Kinetis k64f board
programming and debug interface, via a K20DX device, separate from the
K64 USB interface connected directly to the k64f device). I also have
Ethernet (nsh via telnet) functioning.
I have built the PL2303 & CDCACM apps, neither produce a usb device
visible from Linux laptop
Output of dmesg (PL2303 app with some USB debug enabled)
nsh> dmesg
__start: Reset status: 00:00
khci_hwinitialize: BDT Address 0
khci_hwinitialize: BDTPAGE3 1f
khci_hwinitialize: BDTPAGE2 ff
khci_hwinitialize: BDTPAGE1 46
Mounting procfs to /proc
Successfully bound SDHC to the MMC/SD driver
kinetis_usbsuspend: resume: 1
Output of journalctl on linux PC connected via USB hub to K64 USB
interface
Feb 13 10:18:21 stewart-Inspiron-5559 kernel: usb 1-2.4: new
full-speed USB device number 124 using xhci_hcd
Feb 13 10:18:21 stewart-Inspiron-5559 kernel: usb 1-2.4: device
descriptor read/64, error -32
Feb 13 10:18:21 stewart-Inspiron-5559 kernel: usb 1-2.4: device
descriptor read/64, error -32
Feb 13 10:18:22 stewart-Inspiron-5559 kernel: usb 1-2.4: new
full-speed USB device number 125 using xhci_hcd
Feb 13 10:18:22 stewart-Inspiron-5559 kernel: usb 1-2.4: device
descriptor read/64, error -32
Feb 13 10:18:22 stewart-Inspiron-5559 kernel: usb 1-2.4: device
descriptor read/64, error -32
Feb 13 10:18:22 stewart-Inspiron-5559 kernel: usb 1-2-port4: attempt
power cycle
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: new
full-speed USB device number 126 using xhci_hcd
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: Device not
responding to setup address.
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: Device not
responding to setup address.
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: device not
accepting address 126, error -71
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: new
full-speed USB device number 127 using xhci_hcd
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: Device not
responding to setup address.
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: Device not
responding to setup address.
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2.4: device not
accepting address 127, error -71
Feb 13 10:18:23 stewart-Inspiron-5559 kernel: usb 1-2-port4: unable to
enumerate USB device
Kind regards
Stewart Charnell
