test13 is now available for test and review. thx again! > On Oct 26, 2020, at 12:06 PM, Jim Jagielski <[email protected]> wrote: > > Thanks... we *seem* to be narrowing down to raptor2 as the possible cause. > >> On Oct 26, 2020, at 11:44 AM, Matthias Seidel <[email protected]> >> wrote: >> >> Hi Jim, >> >> Confirming the error messages with test12. >> >> Matthias >> >> Am 26.10.20 um 16:18 schrieb Jim Jagielski: >>> Thanks... I'll wait for at least one additional confirmation that this one >>> is bad before I kick off #13 >>> >>>> On Oct 26, 2020, at 11:11 AM, Pedro Lino <[email protected]> >>>> wrote: >>>> >>>> Hi Jim >>>> >>>> Still the same errors on Ubuntu 18.04.5 x64 >>>> >>>> Pedro >>>> >>>>> On 10/26/2020 1:56 PM Jim Jagielski <[email protected]> wrote: >>>>> >>>>> >>>>> test12 is now available... you know where :) >>>>> >>>>>> On Oct 26, 2020, at 7:12 AM, André Pereira <[email protected]> wrote: >>>>>> >>>>>> teste11 >>>>>> Here with Debian 10 64bits I have "General Error" message when opening >>>>>> odt >>>>>> file and "Not all attributes could be read" when opening ods file. Saving >>>>>> gives no error. The terminal gives "Failed to load module "atk-bridge"". >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> On Sun, Oct 25, 2020 at 10:40 PM Carl Marcum <[email protected]> wrote: >>>>>> >>>>>>> Hi Jim, >>>>>>> >>>>>>> On 10/25/20 8:16 PM, Jim Jagielski wrote: >>>>>>>> And test11 is now available for test >>>>>>> Getting the General Error opening Writer documents and when saving a new >>>>>>> document. >>>>>>> I don't get the error again when saving after opening an existing >>>>>>> document and saving it. >>>>>>> >>>>>>> I get the Not all attributes could be read error when opening an >>>>>>> existing Calc doc but it saves okay. >>>>>>> A new Calc document saves okay. >>>>>>> >>>>>>> Best regards, >>>>>>> Carl >>>>>>> >>>>>>>>> On Oct 25, 2020, at 2:11 PM, Carl Marcum <[email protected]> wrote: >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> On 10/25/20 1:04 PM, Matthias Seidel wrote: >>>>>>>>>> Am 25.10.20 um 17:46 schrieb Jim Jagielski: >>>>>>>>>>> test10 builds are now available... >>>>>>>>>> I still get "General Error" >>>>>>>>>> >>>>>>>>> I also get the Error on Ubuntu 18.04 x86-64 on test 10. >>>>>>>>> >>>>>>>>> Thanks, >>>>>>>>> Carl >>>>>>>>> >>>>>>>>> >>>>>>>>> --------------------------------------------------------------------- >>>>>>>>> To unsubscribe, e-mail: [email protected] >>>>>>>>> For additional commands, e-mail: [email protected] >>>>>>>>> >>>>>>>> --------------------------------------------------------------------- >>>>>>>> To unsubscribe, e-mail: [email protected] >>>>>>>> For additional commands, e-mail: [email protected] >>>>>>>> >>>>>>> >>>>>>> --------------------------------------------------------------------- >>>>>>> To unsubscribe, e-mail: [email protected] >>>>>>> For additional commands, e-mail: [email protected] >>>>>>> >>>>>>> >>>>> >>>>> --------------------------------------------------------------------- >>>>> To unsubscribe, e-mail: [email protected] >>>>> For additional commands, e-mail: [email protected] >>>> --------------------------------------------------------------------- >>>> To unsubscribe, e-mail: [email protected] >>>> For additional commands, e-mail: [email protected] >>>> >>> >>> --------------------------------------------------------------------- >>> To unsubscribe, e-mail: [email protected] >>> For additional commands, e-mail: [email protected] >>> >> > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [email protected] > For additional commands, e-mail: [email protected] >
--------------------------------------------------------------------- To unsubscribe, e-mail: [email protected] For additional commands, e-mail: [email protected]
