Hi Jon, config was the one below. But couldn't make it work. Also changing collector for http://localhost:9411/api/v1/spans does not work as well.
geronimo.opentracing.span.converter.zipkin.sender=http geronimo.opentracing.span.converter.zipkin.http.collector= http://localhost:9411/api/v2/spans geronimo.opentracing.span.converter.zipkin.http.bulkSendInterval=6000 geronimo.opentracing.span.converter.zipkin.http.maxSpansPerBulk=1 geronimo.opentracing.span.converter.zipkin.http.maxSpansIteration=1 geronimo.opentracing.span.converter.zipkin.http.bufferSize=1 Thanks! On Wed, Apr 24, 2019 at 9:00 AM Jonathan Gallimore < [email protected]> wrote: > Hey Ivan, > > What config are you using? I have this setup here with the following > properties, and absolutely nothing goes over the wire to ZipKin. I put a > debugger on the server and the CDI event for FinishedSpan never gets fired, > so nothing gets collected to be sent to ZipKin. I can probably help with > your issue, but I'll need to get to a point where something gets sent, even > if its rejected at the ZipKin end. > > -Dgeronimo.opentracing.zipkin.serviceName=demo > -Dgeronimo.opentracing.span.converter.zipkin.sender=http > -Dgeronimo.opentracing.span.converter.zipkin.http.collector= > http://zipkin:9411/api/v2/spans > > -Dgeronimo.opentracing.span.converter.zipkin.http.bulkSendInterval=5000 > > Jon > > On Mon, Apr 15, 2019 at 11:19 PM Ivan Junckes Filho <[email protected] > > > wrote: > > > Cool, these are good tips I will try both. I didn't try v1 yet. > > > > On Mon, Apr 15, 2019 at 5:00 PM Romain Manni-Bucau < > [email protected]> > > wrote: > > > > > Hmm, missed that but did you try using v1 instead of v2 endpoint? > > > > > > Side note: if it helps you to test move the delay to -1 to not wait the > > > interval. > > > > > > Le lun. 15 avr. 2019 à 20:36, Ivan Junckes Filho < > [email protected]> > > > a écrit : > > > > > >> Romain I was actually using this docker-compose from JL as reference, > > but > > >> wasn't able to make it work. > > >> > > >> I will have a look at it again this week, if I have improvement I will > > >> let you know. > > >> > > >> If you have any other tips let me know. > > >> > > >> Thanks for the reply! > > >> > > >> On Fri, Apr 12, 2019 at 6:25 PM Romain Manni-Bucau < > > [email protected]> > > >> wrote: > > >> > > >>> Hi Ivan > > >>> > > >>> Did you debug ZipkinHttp? > > >>> > > >>> Depending your server/app config you can need some config like > > providers > > >>> etc. This class is a good start to check what is happening. > > >>> > > >>> A good config start is > > >>> > > >>> > > > https://github.com/jeanouii/microprofile-samples/blob/master/docker-compose.yaml > > >>> - you can need to inline the yaml depending you docker compose > > >>> version/setup, multiline is not always well supported. > > >>> > > >>> > > >>> > > >>> Le ven. 12 avr. 2019 à 22:10, Ivan Junckes Filho < > > [email protected]> > > >>> a > > >>> écrit : > > >>> > > >>> > Hey guys I am having a hard time to setup TomEE with OpenTracing > > 1.0.2 > > >>> + > > >>> > Zipkin. > > >>> > > > >>> > When I send the payload to the zipkin API > > >>> > http://localhost:9411/api/v2/spans, I keep getting back: > > >>> > 400 - "Expected a JSON_V2 encoded list, but received: JSON_V1" > > >>> > > > >>> > My payload is: > > >>> > [ > > >>> > { > > >>> > "annotations": [ > > >>> > { > > >>> > "timestamp": 1555097175276000, > > >>> > "value": "sr" > > >>> > }, > > >>> > { > > >>> > "timestamp": 1555097175402000, > > >>> > "value": "ss" > > >>> > } > > >>> > ], > > >>> > "binaryAnnotations": [ > > >>> > { > > >>> > "key": "http.status_code", > > >>> > "type": 3, > > >>> > "value": 200 > > >>> > }, > > >>> > { > > >>> > "key": "component", > > >>> > "type": 6, > > >>> > "value": "jaxrs" > > >>> > }, > > >>> > { > > >>> > "key": "span.kind", > > >>> > "type": 6, > > >>> > "value": "server" > > >>> > }, > > >>> > { > > >>> > "key": "http.url", > > >>> > "type": 6, > > >>> > "value": " > http://localhost:8081/number-api/numbers/generate"; > > >>> > }, > > >>> > { > > >>> > "key": "http.method", > > >>> > "type": 6, > > >>> > "value": "GET" > > >>> > } > > >>> > ], > > >>> > "duration": 126000, > > >>> > "id": 2, > > >>> > "kind": "SERVER", > > >>> > "localEndpoint": { > > >>> > "ipv4": "127.0.0.1", > > >>> > "port": 8081, > > >>> > "serviceName": "number-api" > > >>> > }, > > >>> > "name": > > >>> > > > >>> > > > "GET:com.microprofile.samples.services.number.resource.NumberResource.generate", > > >>> > "parentId": 1, > > >>> > "tags": { > > >>> > "http.status_code": "200", > > >>> > "component": "jaxrs", > > >>> > "http.url": " > http://localhost:8081/number-api/numbers/generate > > ", > > >>> > "http.method": "GET" > > >>> > }, > > >>> > "timestamp": 1555097175276000, > > >>> > "traceId": 24 > > >>> > } > > >>> > ] > > >>> > > > >>> > Any ideas how to fix this? Anyone was able to configure zipkin as > a > > >>> > collector using TomEE? > > >>> > > > >>> > > >> > > >
