More info on dmesg and /proc/bus/usb
Obviously, slackware can see Marvell wireless now but cannot see eth0 :(
Please help.
I try the same using ututo.igz and got the same result as in slackware.
So, usb8xxx is work only by luck under fedora only.
The problem to bring it up globally still exist.
Now I made slackware to have below info in OLPC:
============
Adding info for ac97:0-0:AD1888
ide_core: exports duplicate symbol noautodma (owned by kernel)
AMD5536: IDE controller at PCI slot 0000:00:0f.2
AMD5536: chipset revision 1
AMD5536: not 100% native mode: will probe irqs later
AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller
AMD5536: neither IDE port enabled (BIOS)
ide_core: exports duplicate symbol noautodma (owned by kernel)
usb8xxx: probe of 1-4:1.0 failed with error -12
usbcore: registered new driver usb8xxx
usbcore: deregistering driver usb8xxx
request_firmware() failed, error code = 0xfffffffe
usb8388.bin not found in /lib/firmware
unregister_netdevice: device eth%d/c4470000 never was registered
usb8xxx: probe of 1-4:1.0 failed with error -12
usbcore: registered new driver usb8xxx
usbcore: deregistering driver usb8xxx
usb 1-2: new high speed USB device using ehci_hcd and address 5
PM: Adding info for usb:1-2
PM: Adding info for No Bus:usbdev1.5_ep00
usb 1-2: configuration #1 chosen from 1 choice
PM: Adding info for usb:1-2:1.0
scsi1 : SCSI emulation for USB Mass Storage devices
PM: Adding info for No Bus:host1
PM: Adding info for No Bus:usbdev1.5_ep81
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:usbdev1.5_ep02
PM: Adding info for No Bus:usbdev1.5
PM: Adding info for No Bus:target1:0:0
Vendor: Kingston Model: DataTraveler 2.0 Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
PM: Adding info for scsi:1:0:0:0
SCSI device sdb: 977664 512-byte hdwr sectors (501 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 977664 512-byte hdwr sectors (501 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1 sdb2
sd 1:0:0:0: Attached scsi removable disk sdb
PM: Adding info for No Bus:target1:0:1
PM: Removing info for No Bus:target1:0:1
PM: Adding info for No Bus:target1:0:2
PM: Removing info for No Bus:target1:0:2
PM: Adding info for No Bus:target1:0:3
PM: Removing info for No Bus:target1:0:3
PM: Adding info for No Bus:target1:0:4
PM: Removing info for No Bus:target1:0:4
PM: Adding info for No Bus:target1:0:5
PM: Removing info for No Bus:target1:0:5
PM: Adding info for No Bus:target1:0:6
PM: Removing info for No Bus:target1:0:6
PM: Adding info for No Bus:target1:0:7
PM: Removing info for No Bus:target1:0:7
usb-storage: device scan complete
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
request_firmware() failed, error code = 0xfffffffe
usb8388.bin not found in /lib/firmware
unregister_netdevice: device eth%d/c45fd000 never was registered
usb8xxx: probe of 1-4:1.0 failed with error -12
usbcore: registered new driver usb8xxx
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 4
B: Alloc= 28/900 us ( 3%), #Int= 2, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-rc2 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:0f.4
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=04d9 ProdID=1203 Rev= 2.60
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 4
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-rc2 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:0f.5
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=13fe ProdID=1a00 Rev= 1.00
S: Manufacturer=Kingston
S: Product=DataTraveler 2.0
S: SerialNumber=5B650B009857
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=13fe ProdID=1a00 Rev= 1.00
S: Manufacturer=Kingston
S: Product=DataTraveler 2.0
S: SerialNumber=5B64050003AE
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1286 ProdID=2001 Rev=30.06
S: Manufacturer=Marvell
S: Product=MARVELL Wireless Device
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
On Tue, 5 Sep 2006, [EMAIL PROTECTED] wrote:
On Tue, 5 Sep 2006, Jim Gettys wrote:
On Mon, 2006-09-04 at 21:05 -0800, [EMAIL PROTECTED] wrote:
On Mon, 4 Sep 2006, James Cameron wrote:
On Mon, Sep 04, 2006 at 02:22:00PM -0800, [EMAIL PROTECTED] wrote:
After I burn OLPC to Linux BIOS, seem it is always has error messages at
the beginning like:
ACPI ... DSCP not found ??
I don't get this message, and besides since ACPI is not planned to be
present I wouldn't be concerned if I did see such a message. Does the
system boot anyway? When during the boot process do you see this
message? What are you booting?
I am careless. The exact words is what you said "ACPI: Unable to locate
RSDP"
Can this cause problem to slackware to be unable to find the firmware?
Seems unlikely.
Booting build 81 shows in dmesg "ACPI: Unable to locate RSDP", and
"ACPI: Interpreter disabled." This is expected.
I press F1 and it has only images.
This seems normal. F1 enters the image menu, then you use left and
right arrow keys to select an image. The last image, on my board, gives
a LinuxBIOS shell prompt.
Even not press the arrows finally it will boot USB after cannot find the
NAND memory devices.
a LinuxBIOS shell prompt?
I will not call it. Because boot from utotu CD or slak CD can have the
same initrd shell.
You must be using fbdev after LinuxBIOS is installed: there is no VESA
support in our LinuxBIOS load.
IMO: Linux shell prompt should be capable to config some things like
change date, change CPU speed, change boot priority, etc.
Changing date should be done from Linux; there is no need for setting it
in the BIOS.
Which device is booted is determined by shell scripts in the Linux that
is the payload of LinuxBIOS. If you want to implement such
functionality, you are welcome to help.
I am not sure that is feature or bug.
It seems to be a feature.
OK. Thank you to let me know my BIOS linux is normal.
Could you please verify me that :
There is no way under linux BIOS to config the OLPC devices?
Perhaps the source code would show what it is capable of, or perhaps we
need to wait for documentation on what configuration options are
available. Is there any reason you need to configure devices? Why
shouldn't Linux be able to do this configuration? We control the BIOS,
there seems no justification for device configuration functionality.
Earlier BIOS control Marvell Wireless by reset or power-off.
Now. Fedora can control Marvell Wireless completely in good shape w/o need
reset/power-off but unfortunately I cannot find out how slackware can do
the same :(
It is slackware's responsibility to pick up device drivers for OLPC, at
least until they enter the kernel.org source pool. I know Marcelo has
been planning some further cleanup of the driver before submission to
kernel.org.
If so, after I power-off, is thare any way to bring back the old BIOS.
Perhaps. I've not tested it, and I'm not willing to. You should be
able to boot from the same filesystem you did the olpcflash commands on.
But why would you need to do this at all? Why do you need ACPI?
I don't know. Because I only see that error and that error correlated or
co-incident with slackware become unable to make usb8xxx to work
correctly. :(
I don't know what you mean by usb8xxx.
As Marcelo notes,
1) cat /proc/bus/usb/devices
2) dmesg
Under OLPC using slackware /proc/bus/usb/devices did NOT exist.
The kernel and initrd on slackware that did not run OLPC produce below cat
/proc/bus/usb/devices:
...
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0930 ProdID=653d Rev= 2.00
S: Manufacturer=KINGSTON
S: Product=DataTraveler I
S: SerialNumber=0F80D4604162E493
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 94mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
....
dmesg on slackware OLPC using my bzImage produce:
ide_scsi: Unknown symbol kmap_atomic
ide_scsi: Unknown symbol kunmap_atomic
ide_scsi: Unknown symbol page_address
ipv6: Unknown symbol page_address
ipv6: Unknown symbol page_address
request_firmware() failed, error code = 0xfffffffe
usb8388.bin not found in /lib/firmware
unregister_netdevice: device eth%d/c7259000 never was registered
usb8xxx: probe of 1-4:1.0 failed with error -12
usbcore: registered new driver usb8xxx
...
dmesg on slackware OLPC using my original olpc_vmlinuz produce:
PM: Removing info for No Bus:target0:0:6
PM: Adding info for No Bus:target0:0:7
PM: Removing info for No Bus:target0:0:7
usb-storage: device scan complete
Adding 44632k swap on /dev/sda2. Priority:-1 extents:1 across:44632k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
usb8xxx: probe of 1-4:1.0 failed with error -12
usbcore: registered new driver usb8xxx
------------
I see that under slackware BUS of usb8388 did not exist :(
Please help.
the kernal loading command is identical to your original:
#!/bin/sh
ROOTFS=/key
ROOT=LABEL=OLPCRoot
ROOTFSTYPE=ext3
if [ -d /flash/boot ] ; then
ROOTFS=/flash
ROOT=mtd0
ROOTFSTYPE=jffs2
fi
/sbin/kbl-kexec $ROOTFS/boot/olpc-vmlinuz "ro quiet root=$ROOT
rootfstype=$ROOTF
STYPE console=ttyS0,115200 console=tty0 fbcon=font:SUN12x22 pci=nobios
video=gxf
b:1024x768-16" $ROOTFS/boot/olpc-initrd.img
regards,
supat
_______________________________________________
Devel mailing list
[email protected]
http://mailman.laptop.org/mailman/listinfo/devel
