From: Mark Rankilor <[email protected]> This patches fixes long line lengths in comedi.h that were picked up by checkpatch.pl
Signed-off-by: Mark Rankilor <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> --- drivers/staging/comedi/comedi.h | 32 ++++++++++++++++++-------------- 1 files changed, 18 insertions(+), 14 deletions(-) diff --git a/drivers/staging/comedi/comedi.h b/drivers/staging/comedi/comedi.h index 1538146..3e3663f 100644 --- a/drivers/staging/comedi/comedi.h +++ b/drivers/staging/comedi/comedi.h @@ -465,7 +465,8 @@ #define COMEDI_CB_EOS 1 /* end of scan */ #define COMEDI_CB_EOA 2 /* end of acquisition */ -#define COMEDI_CB_BLOCK 4 /* data has arrived: wakes up read() / write() */ +#define COMEDI_CB_BLOCK 4 /* data has arrived: + * wakes up read() / write() */ #define COMEDI_CB_EOBUF 8 /* DEPRECATED: end of buffer */ #define COMEDI_CB_ERROR 16 /* card error during acquisition */ #define COMEDI_CB_OVERFLOW 32 /* buffer overflow/underflow */ @@ -499,8 +500,10 @@ I8254_MODE2 = (2 << 1), /* Rate generator */ I8254_MODE3 = (3 << 1), /* Square wave mode */ I8254_MODE4 = (4 << 1), /* Software triggered strobe */ - I8254_MODE5 = (5 << 1), /* Hardware triggered strobe (retriggerable) */ - I8254_BCD = 1, /* use binary-coded decimal instead of binary (pretty useless) */ + I8254_MODE5 = (5 << 1), /* Hardware triggered strobe + * (retriggerable) */ + I8254_BCD = 1, /* use binary-coded decimal instead of binary + * (pretty useless) */ I8254_BINARY = 0 }; @@ -640,7 +643,8 @@ May be bitwise-or'd with CR_EDGE or CR_INVERT. */ NI_GPCT_UP_DOWN_PIN_i_GATE_SELECT = 0x201, NI_GPCT_SELECTED_GATE_GATE_SELECT = 0x21e, /* m-series "second gate" sources are unknown, - we should add them here with an offset of 0x300 when known. */ + * we should add them here with an offset of 0x300 when + * known. */ NI_GPCT_DISABLED_GATE_SELECT = 0x8000, }; static inline unsigned NI_GPCT_GATE_PIN_GATE_SELECT(unsigned n) @@ -681,14 +685,14 @@ INSN_CONFIG_SET_OTHER_SRC when using NI general-purpose counters. */ INSN_CONFIG_ARM */ enum ni_gpct_arm_source { NI_GPCT_ARM_IMMEDIATE = 0x0, - NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1, /* Start both the counter and - the adjacent paired counter - simultaneously */ - /* NI doesn't document bits for selecting hardware arm triggers. If - * the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least - * significant bits (3 bits for 660x or 5 bits for m-series) through to - * the hardware. This will at least allow someone to figure out what - * the bits do later. */ + NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1, /* Start both the counter + * and the adjacent paired + * counter simultaneously */ + /* NI doesn't document bits for selecting hardware arm triggers. + * If the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least + * significant bits (3 bits for 660x or 5 bits for m-series) + * through to the hardware. This will at least allow someone to + * figure out what the bits do later. */ NI_GPCT_ARM_UNKNOWN = 0x1000, }; @@ -740,8 +744,8 @@ INSN_CONFIG_ARM */ NI_RTSI_OUTPUT_G_GATE0 = 6, NI_RTSI_OUTPUT_RGOUT0 = 7, NI_RTSI_OUTPUT_RTSI_BRD_0 = 8, - NI_RTSI_OUTPUT_RTSI_OSC = 12 /* pre-m-series always have RTSI clock - on line 7 */ + NI_RTSI_OUTPUT_RTSI_OSC = 12 /* pre-m-series always have RTSI + * clock on line 7 */ }; static inline unsigned NI_RTSI_OUTPUT_RTSI_BRD(unsigned n) { -- 1.7.0.3 _______________________________________________ devel mailing list [email protected] http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
