Related changes: - Included example to show usage as generic (non-swap) disk with ext4 filesystem. - Renamed rzscontrol to zramconfig to match with new device naming.
Signed-off-by: Nitin Gupta <[email protected]> --- drivers/staging/zram/zram.txt | 113 ++++++++++++++++++++++------------------ 1 files changed, 62 insertions(+), 51 deletions(-) rewrite drivers/staging/zram/zram.txt (73%) diff --git a/drivers/staging/zram/zram.txt b/drivers/staging/zram/zram.txt dissimilarity index 73% index 9694acf..520edc1 100644 --- a/drivers/staging/zram/zram.txt +++ b/drivers/staging/zram/zram.txt @@ -1,51 +1,62 @@ -ramzswap: Compressed RAM based swap device -------------------------------------------- - -Project home: http://compcache.googlecode.com/ - -* Introduction - -The ramzswap module creates RAM based block devices which can (only) be used as -swap disks. Pages swapped to these devices are compressed and stored in memory -itself. See project home for use cases, performance numbers and a lot more. - -Individual ramzswap devices are configured and initialized using rzscontrol -userspace utility as shown in examples below. See rzscontrol man page for more -details. - -* Usage - -Following shows a typical sequence of steps for using ramzswap. - -1) Load Modules: - modprobe ramzswap num_devices=4 - This creates 4 (uninitialized) devices: /dev/ramzswap{0,1,2,3} - (num_devices parameter is optional. Default: 1) - -2) Initialize: - Use rzscontrol utility to configure and initialize individual - ramzswap devices. Example: - rzscontrol /dev/ramzswap2 --init # uses default value of disksize_kb - - *See rzscontrol man page for more details and examples* - -3) Activate: - swapon /dev/ramzswap2 # or any other initialized ramzswap device - -4) Stats: - rzscontrol /dev/ramzswap2 --stats - -5) Deactivate: - swapoff /dev/ramzswap2 - -6) Reset: - rzscontrol /dev/ramzswap2 --reset - (This frees all the memory allocated for this device). - - -Please report any problems at: - - Mailing list: linux-mm-cc at laptop dot org - - Issue tracker: http://code.google.com/p/compcache/issues/list - -Nitin Gupta [email protected] +zram: Compressed RAM based block devices +---------------------------------------- + +Project home: http://compcache.googlecode.com/ + +* Introduction + +The zram module creates RAM based block devices: /dev/ramX (X = 0, 1, ...). +Pages written to these disks are compressed and stored in memory itself. +These disks allow very fast I/O and compression provides good amounts of +memory savings. + +See project home for use cases, performance numbers and a lot more. + +Individual zram devices are configured and initialized using zramconfig +userspace utility as shown in examples below. See zramconfig man page for +more details. + +* Usage + +Following shows a typical sequence of steps for using zram. + +1) Load Modules: + modprobe zram num_devices=4 + This creates 4 (uninitialized) devices: /dev/zram{0,1,2,3} + (num_devices parameter is optional. Default: 1) + +2) Initialize: + Use zramconfig utility to configure and initialize individual + zram devices. For example: + zramconfig /dev/zram0 --init # uses default value of disksize_kb + zramconfig /dev/zram1 --disksize_kb=102400 # 100MB /dev/zram1 + + *See zramconfig man page for more details and examples* + +3) Activate: + mkswap /dev/zram0 + swapon /dev/zram0 + + mkfs.ext4 /dev/zram1 + mount /dev/zram1 /tmp + +4) Stats: + zramconfig /dev/zram0 --stats + zramconfig /dev/zram1 --stats + +5) Deactivate: + swapoff /dev/zram0 + umount /dev/zram1 + +6) Reset: + zramconfig /dev/zram0 --reset + zramconfig /dev/zram1 --reset + (This frees memory allocated for the given device). + + +Please report any problems at: + - Mailing list: linux-mm-cc at laptop dot org + - Issue tracker: http://code.google.com/p/compcache/issues/list + +Nitin Gupta [email protected] -- 1.7.0.1 _______________________________________________ devel mailing list [email protected] http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
