Signed-off-by: Kalle Valo <[email protected]>
---
drivers/net/wireless/ath/ath6kl/target.h | 331 ++++++++++++++++++++++++++++++
1 files changed, 331 insertions(+), 0 deletions(-)
create mode 100644 drivers/net/wireless/ath/ath6kl/target.h
diff --git a/drivers/net/wireless/ath/ath6kl/target.h
b/drivers/net/wireless/ath/ath6kl/target.h
new file mode 100644
index 0000000..519a013
--- /dev/null
+++ b/drivers/net/wireless/ath/ath6kl/target.h
@@ -0,0 +1,331 @@
+/*
+ * Copyright (c) 2004-2010 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef TARGET_H
+#define TARGET_H
+
+#define AR6003_BOARD_DATA_SZ 1024
+#define AR6003_BOARD_EXT_DATA_SZ 768
+
+#define RESET_CONTROL_ADDRESS 0x00000000
+#define RESET_CONTROL_COLD_RST 0x00000100
+#define RESET_CONTROL_MBOX_RST 0x00000004
+
+#define CPU_CLOCK_STANDARD_S 0
+#define CPU_CLOCK_STANDARD 0x00000003
+#define CPU_CLOCK_ADDRESS 0x00000020
+
+#define CLOCK_CONTROL_ADDRESS 0x00000028
+#define CLOCK_CONTROL_LF_CLK32_S 2
+#define CLOCK_CONTROL_LF_CLK32 0x00000004
+
+#define SYSTEM_SLEEP_ADDRESS 0x000000c4
+#define SYSTEM_SLEEP_DISABLE_S 0
+#define SYSTEM_SLEEP_DISABLE 0x00000001
+
+#define LPO_CAL_ADDRESS 0x000000e0
+#define LPO_CAL_ENABLE_S 20
+#define LPO_CAL_ENABLE 0x00100000
+
+#define GPIO_PIN10_ADDRESS 0x00000050
+#define GPIO_PIN11_ADDRESS 0x00000054
+#define GPIO_PIN12_ADDRESS 0x00000058
+#define GPIO_PIN13_ADDRESS 0x0000005c
+
+#define HOST_INT_STATUS_ADDRESS 0x00000400
+#define HOST_INT_STATUS_ERROR_S 7
+#define HOST_INT_STATUS_ERROR 0x00000080
+
+#define HOST_INT_STATUS_CPU_S 6
+#define HOST_INT_STATUS_CPU 0x00000040
+
+#define HOST_INT_STATUS_COUNTER_S 4
+#define HOST_INT_STATUS_COUNTER 0x00000010
+
+#define CPU_INT_STATUS_ADDRESS 0x00000401
+
+#define ERROR_INT_STATUS_ADDRESS 0x00000402
+#define ERROR_INT_STATUS_WAKEUP_S 2
+#define ERROR_INT_STATUS_WAKEUP 0x00000004
+
+#define ERROR_INT_STATUS_RX_UNDERFLOW_S 1
+#define ERROR_INT_STATUS_RX_UNDERFLOW 0x00000002
+
+#define ERROR_INT_STATUS_TX_OVERFLOW_S 0
+#define ERROR_INT_STATUS_TX_OVERFLOW 0x00000001
+
+#define COUNTER_INT_STATUS_ADDRESS 0x00000403
+#define COUNTER_INT_STATUS_COUNTER_S 0
+#define COUNTER_INT_STATUS_COUNTER 0x000000ff
+
+#define RX_LOOKAHEAD_VALID_ADDRESS 0x00000405
+
+#define INT_STATUS_ENABLE_ADDRESS 0x00000418
+#define INT_STATUS_ENABLE_ERROR_S 7
+#define INT_STATUS_ENABLE_ERROR 0x00000080
+
+#define INT_STATUS_ENABLE_CPU_S 6
+#define INT_STATUS_ENABLE_CPU 0x00000040
+
+#define INT_STATUS_ENABLE_INT_S 5
+#define INT_STATUS_ENABLE_INT 0x00000020
+#define INT_STATUS_ENABLE_COUNTER_S 4
+#define INT_STATUS_ENABLE_COUNTER 0x00000010
+
+#define INT_STATUS_ENABLE_MBOX_DATA_S 0
+#define INT_STATUS_ENABLE_MBOX_DATA 0x0000000f
+
+#define CPU_INT_STATUS_ENABLE_ADDRESS 0x00000419
+#define CPU_INT_STATUS_ENABLE_BIT_S 0
+#define CPU_INT_STATUS_ENABLE_BIT 0x000000ff
+
+#define ERROR_STATUS_ENABLE_ADDRESS 0x0000041a
+#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_S 1
+#define ERROR_STATUS_ENABLE_RX_UNDERFLOW 0x00000002
+
+#define ERROR_STATUS_ENABLE_TX_OVERFLOW_S 0
+#define ERROR_STATUS_ENABLE_TX_OVERFLOW 0x00000001
+
+#define COUNTER_INT_STATUS_ENABLE_ADDRESS 0x0000041b
+#define COUNTER_INT_STATUS_ENABLE_BIT_S 0
+#define COUNTER_INT_STATUS_ENABLE_BIT 0x000000ff
+
+#define COUNT_ADDRESS 0x00000420
+
+#define COUNT_DEC_ADDRESS 0x00000440
+
+#define WINDOW_DATA_ADDRESS 0x00000474
+#define WINDOW_WRITE_ADDR_ADDRESS 0x00000478
+#define WINDOW_READ_ADDR_ADDRESS 0x0000047c
+#define CPU_DBG_SEL_ADDRESS 0x00000483
+#define CPU_DBG_ADDRESS 0x00000484
+
+#define LOCAL_SCRATCH_ADDRESS 0x000000c0
+#define ATH6KL_OPTION_SLEEP_DISABLE 0x08
+
+#define RTC_BASE_ADDRESS 0x00004000
+#define GPIO_BASE_ADDRESS 0x00014000
+#define MBOX_BASE_ADDRESS 0x00018000
+#define ANALOG_INTF_BASE_ADDRESS 0x0001c000
+
+/* real name of the register is unknown */
+#define ATH6KL_ANALOG_PLL_REGISTER (ANALOG_INTF_BASE_ADDRESS + 0x284)
+
+#define SM(f, v) (((v) << f##_S) & f)
+#define MS(f, v) (((v) & f) >> f##_S)
+
+/*
+ * xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the
+ * host_interest structure.
+ *
+ * Host Interest is shared between Host and Target in order to coordinate
+ * between the two, and is intended to remain constant (with additions only
+ * at the end).
+ */
+#define ATH6KL_HI_START_ADDR 0x00540600
+
+/*
+ * These are items that the Host may need to access
+ * via BMI or via the Diagnostic Window. The position
+ * of items in this structure must remain constant.
+ * across firmware revisions!
+ *
+ * Types for each item must be fixed size across target and host platforms.
+ * The structure is used only to calculate offset for each register with
+ * HI_ITEM() macro, no values are stored to it.
+ *
+ * More items may be added at the end.
+ */
+struct host_interest {
+ /*
+ * Pointer to application-defined area, if any.
+ * Set by Target application during startup.
+ */
+ u32 hi_app_host_interest; /* 0x00 */
+
+ /* Pointer to register dump area, valid after Target crash. */
+ u32 hi_failure_state; /* 0x04 */
+
+ /* Pointer to debug logging header */
+ u32 hi_dbglog_hdr; /* 0x08 */
+
+ u32 hi_unused1; /* 0x0c */
+
+ /*
+ * General-purpose flag bits, similar to ATH6KL_OPTION_* flags.
+ * Can be used by application rather than by OS.
+ */
+ u32 hi_option_flag; /* 0x10 */
+
+ /*
+ * Boolean that determines whether or not to
+ * display messages on the serial port.
+ */
+ u32 hi_serial_enable; /* 0x14 */
+
+ /* Start address of DataSet index, if any */
+ u32 hi_dset_list_head; /* 0x18 */
+
+ /* Override Target application start address */
+ u32 hi_app_start; /* 0x1c */
+
+ /* Clock and voltage tuning */
+ u32 hi_skip_clock_init; /* 0x20 */
+ u32 hi_core_clock_setting; /* 0x24 */
+ u32 hi_cpu_clock_setting; /* 0x28 */
+ u32 hi_system_sleep_setting; /* 0x2c */
+ u32 hi_xtal_control_setting; /* 0x30 */
+ u32 hi_pll_ctrl_setting_24ghz; /* 0x34 */
+ u32 hi_pll_ctrl_setting_5ghz; /* 0x38 */
+ u32 hi_ref_voltage_trim_setting; /* 0x3c */
+ u32 hi_clock_info; /* 0x40 */
+
+ /*
+ * Flash configuration overrides, used only
+ * when firmware is not executing from flash.
+ * (When using flash, modify the global variables
+ * with equivalent names.)
+ */
+ u32 hi_bank0_addr_value; /* 0x44 */
+ u32 hi_bank0_read_value; /* 0x48 */
+ u32 hi_bank0_write_value; /* 0x4c */
+ u32 hi_bank0_config_value; /* 0x50 */
+
+ /* Pointer to Board Data */
+ u32 hi_board_data; /* 0x54 */
+ u32 hi_board_data_initialized; /* 0x58 */
+
+ u32 hi_dset_ram_index_tbl; /* 0x5c */
+
+ u32 hi_desired_baud_rate; /* 0x60 */
+ u32 hi_dbglog_config; /* 0x64 */
+ u32 hi_end_ram_reserve_sz; /* 0x68 */
+ u32 hi_mbox_io_block_sz; /* 0x6c */
+
+ u32 hi_num_bpatch_streams; /* 0x70 -- unused */
+ u32 hi_mbox_isr_yield_limit; /* 0x74 */
+
+ u32 hi_refclk_hz; /* 0x78 */
+ u32 hi_ext_clk_detected; /* 0x7c */
+ u32 hi_dbg_uart_txpin; /* 0x80 */
+ u32 hi_dbg_uart_rxpin; /* 0x84 */
+ u32 hi_hci_uart_baud; /* 0x88 */
+ u32 hi_hci_uart_pin_assignments; /* 0x8C */
+ /*
+ * NOTE: byte [0] = tx pin, [1] = rx pin, [2] = rts pin, [3] = cts
+ * pin
+ */
+ u32 hi_hci_uart_baud_scale_val; /* 0x90 */
+ u32 hi_hci_uart_baud_step_val; /* 0x94 */
+
+ u32 hi_allocram_start; /* 0x98 */
+ u32 hi_allocram_sz; /* 0x9c */
+ u32 hi_hci_bridge_flags; /* 0xa0 */
+ u32 hi_hci_uart_support_pins; /* 0xa4 */
+ /*
+ * NOTE: byte [0] = RESET pin (bit 7 is polarity),
+ * bytes[1]..bytes[3] are for future use
+ */
+ u32 hi_hci_uart_pwr_mgmt_params; /* 0xa8 */
+ /*
+ * 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
+ * [31:16]: wakeup timeout in ms
+ */
+
+ /* Pointer to extended board data */
+ u32 hi_board_ext_data; /* 0xac */
+ u32 hi_board_ext_data_config; /* 0xb0 */
+
+ /*
+ * Bit [0] : valid
+ * Bit[31:16: size
+ */
+ /*
+ * hi_reset_flag is used to do some stuff when target reset.
+ * such as restore app_start after warm reset or
+ * preserve host Interest area, or preserve ROM data, literals etc.
+ */
+ u32 hi_reset_flag; /* 0xb4 */
+ /* indicate hi_reset_flag is valid */
+ u32 hi_reset_flag_valid; /* 0xb8 */
+ u32 hi_hci_uart_pwr_mgmt_params_ext; /* 0xbc */
+ /*
+ * 0xbc - [31:0]: idle timeout in ms
+ */
+ /* ACS flags */
+ u32 hi_acs_flags; /* 0xc0 */
+ u32 hi_console_flags; /* 0xc4 */
+ u32 hi_nvram_state; /* 0xc8 */
+ u32 hi_option_flag2; /* 0xcc */
+
+ /* If non-zero, override values sent to Host in WMI_READY event. */
+ u32 hi_sw_version_override; /* 0xd0 */
+ u32 hi_abi_version_override; /* 0xd4 */
+
+ /*
+ * Percentage of high priority RX traffic to total expected RX traffic -
+ * applicable only to ar6004
+ */
+ u32 hi_hp_rx_traffic_ratio; /* 0xd8 */
+
+ /* test applications flags */
+ u32 hi_test_apps_related ; /* 0xdc */
+ /* location of test script */
+ u32 hi_ota_testscript; /* 0xe0 */
+ /* location of CAL data */
+ u32 hi_cal_data; /* 0xe4 */
+ /* Number of packet log buffers */
+ u32 hi_pktlog_num_buffers; /* 0xe8 */
+
+} __packed;
+
+#define HI_ITEM(item) offsetof(struct host_interest, item)
+
+#define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
+
+#define HI_OPTION_FW_MODE_IBSS 0x0
+#define HI_OPTION_FW_MODE_BSS_STA 0x1
+#define HI_OPTION_FW_MODE_AP 0x2
+
+#define HI_OPTION_NUM_DEV_SHIFT 0x9
+
+#define HI_OPTION_FW_BRIDGE_SHIFT 0x04
+
+/* Fw Mode/SubMode Mask
+|------------------------------------------------------------------------------|
+| SUB | SUB | SUB | SUB | | | |
+| MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0|
+| (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2)
+|------------------------------------------------------------------------------|
+*/
+#define HI_OPTION_FW_MODE_SHIFT 0xC
+
+/* Convert a Target virtual address into a Target physical address */
+#define TARG_VTOP(vaddr) (vaddr & 0x001fffff)
+
+#define AR6003_REV2_APP_START_OVERRIDE 0x944C00
+#define AR6003_REV2_APP_LOAD_ADDRESS 0x543180
+#define AR6003_REV2_BOARD_EXT_DATA_ADDRESS 0x57E500
+#define AR6003_REV2_DATASET_PATCH_ADDRESS 0x57e884
+#define AR6003_REV2_RAM_RESERVE_SIZE 6912
+
+#define AR6003_REV3_APP_START_OVERRIDE 0x945d00
+#define AR6003_REV3_APP_LOAD_ADDRESS 0x545000
+#define AR6003_REV3_BOARD_EXT_DATA_ADDRESS 0x542330
+#define AR6003_REV3_DATASET_PATCH_ADDRESS 0x57FF74
+#define AR6003_REV3_RAM_RESERVE_SIZE 512
+
+#endif
_______________________________________________
devel mailing list
[email protected]
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
