Dear V-SHY HO, I don't see you setup the managed interface.
iw phy phy0 interface add wlan1 type managed. Are you confirm your setup working? Please advice. Thanks Regards, Chun Yeow On Fri, Jun 3, 2011 at 12:08 PM, V-SHY HO <vshy...@hotmail.com> wrote: > Hi, > > I used hostapd and iw tools to create a AP+MP in November 2010. (may be my > command is obsolete) > > this is the command I ran and I skip the route command part > ----------------------------------------------------------------- > > > sudo apt-get install hostapd > > #reboot after install hostapd > > > sudo ifconfig wlan0 down > > sudo iw dev wlan0 del > > sudo iw phy phy0 interface add mesh0 type mp mesh_id > meshid1 > > sudo iw phy phy0 set channel 6 > > sudo ifconfig mesh0 192.168.2.2 netmask 255.255.255.0 up > > > sudo cp /etc/hostapd/hostapd.conf > /etc/hostapd/hostapd.conf.backup > > > sudo vim /etc/hostapd/hostapd.conf > > #The modifications made to /etc/hostapd/hostapd.conf were shown at below > > #interface=wlan1 > > #driver=nl80211 > > #ssid=hoho > > #hw_mode=g > > #channel=11 > > > sudo hostapd -dd /etc/hostapd/hostapd.conf > > #-dd option for debug mode > > #Configuration file: /etc/hostapd/hostapd.conf > > #ctrl_interface_group=0 > > #... > > #Mode: IEEE 802.11g Channel: 11 Frequency: 2462 MHz > > #Using interface wlan1 with hwaddr f0:7d:68:c4:d8:37 and ssid 'hoho' > > #wlan1: Setup of interface done. > > #when message “Setup of interface done.”, > > # CTRL C to stop the executing command (hostapd -dd > /etc/hostapd/hostapd.conf) > > # iwlist mesh0 scanning to check whether this AP was set up properly > > > #-B option is execute hostapd in background > > #ssid will not be set even after –dd option ran > > sudo hostapd -B /etc/hostapd/hostapd.conf > > #Configuration file: /etc/hostapd/hostapd.conf > > #Using interface wlan1 with hwaddr f0:7d:68:c4:d8:37 and ssid 'hoho' > > > sudo ifconfig wlan1 192.168.3.1 > > #check whether the interface wlan1 in master mode > > iwconfig wlan1 > > From > V-SHY HO > > > > > Dear Loiseau Lucien > > > Yes, I can create the interface but I am not able to bring up the interface > > and make it works. > > > Please advice your setup including the use of hostapd. Thanks. > > > Regards, > > Chun Yeow > > > On Sat, May 21, 2011 at 9:08 PM, Loiseau Lucien <loiseau.lucien at > > gmail.com <http://open80211s.com/mailman/listinfo/devel>>wrote: > > >* Hi,*>**>* Here is a procedure that worked with my card (Atheros AR5001X+) > >with the*>* ath5k driver.*>* I used the "iw" tool.*>**>* # iw list | grep > >phy*>* Wiphy phy5*>**>* and then the creation of the two virtual interfaces > >:*>**>* # iw phy phy5 interface add mesh0 type mp mesh_id mymesh*>* # iw phy > >phy5 interface add wlan2 type managed*>**>* # iw dev wlan2 info*>* Interface > >wlan2*>* ifindex 47*>* type managed*>**>* # iw dev mesh0 info*>* > >Interface mesh0*>* ifindex 46*>* type mesh point*>**>**>**>**>* Le > >21/05/2011 08:23, Yeoh Chun Yeow a écrit :*>**>* Dear all,*>**>* Just would > >like know whether the MAP is supported in open80211s. Possible*>* to have > >one radio to act as Mesh STA and normal AP to serve others normal*>* > >STAs.*>**>* Please advice. Thanks*>**>* Regards,*>* Chun Yeow* > > > _______________________________________________ > Devel mailing list > Devel@lists.open80211s.org > http://open80211s.com/mailman/listinfo/devel > >
_______________________________________________ Devel mailing list Devel@lists.open80211s.org http://open80211s.com/mailman/listinfo/devel
