- Network --> Captative Portal --> <*> wifidog why? in L2 mesh the captive portal should run outside the MBSS.
Antonio 2011/11/22 romulo albuquerque <[email protected]> > Hi everybody, > > I have isntalled openwrt backfire buildroot from trunk version in TP-link > TL-WR1043ND. > First I followed the steps from http://o11s.org/trac/wiki/OpenWrtBuilding, > but I had building problems with compat-wireless from > http://o11s.org/files/compat-wireless-2.6-o11s-0.4.2.tar.bz2. So I gave > up those steps and made my on 802.11s enabled image following these other > steps: > > 1- installation: > svn co svn://svn.openwrt.org/openwrt/trunk openwrt > ./scripts/feeds update -a > ./scripts/feeds install -a > make menuconfig > > - Target System --> Atheros AR71xx/AR7240/AR913x/AR934x > - Target Profile --> TP-LINK TL-WR1043ND v1 > - Kernel Module --> Wireless Drivers --> <*> kmod-ath9k > - Network --> Captative Portal --> <*> wifidog > --> File Transfer --> <*> wget > --> <*> iperf > --> <*> tcpdump > --> <*> traceroute > > 2- make V=99 > 3- make kernel_menuconfig > > Networking suport --> wireless --> <M> cfg80211 - wireless configuration > API > --> <M> Generic IEEE 802.11 > Networking Stack (mac80211) > --> <*> Enable > mac80211 mesh networking (pre-802.11s) support > > 4- make V=99 (Then the image was generated in bin/ar71xx) > > 5- I followed the recomended configuration to set up the mesh network: > > router 1 > rmmod ath9k > insmod /lib/modules/2.6.39.4/ath9k.ko nohwcrypt=1 > iw dev wlan0 interface add mesh0 type mp > iw dev mesh0 set channel 6 > ifconfig mesh0 192.168.2.1/24 > iw dev mesh0 mesh join mymesh > > router 2 > rmmod ath9k > insmod /lib/modules/2.6.39.4/ath9k.ko nohwcrypt=1 > iw dev wlan0 interface add mesh0 type mp > iw dev mesh0 set channel 6 > ifconfig mesh0 192.168.2.2/24 > iw dev mesh0 mesh join mymesh > > When I run: > iw dev mesh0 station dump > > I can see this result: > Station d8:5d:4c:d4:fd:7c (on mesh0) > inactive time: 920 ms > rx bytes: 25320 > rx packets: 634 > tx bytes: 223 > tx packets: 3 > tx retries: 0 > tx failed: 0 > signal: -52 dBm > signal avg: -51 [-66, -53, -60] dBm > tx bitrate: 1.0 MBit/s > rx bitrate: 1.0 MBit/s > mesh llid: 65475 > mesh plid: 36832 > mesh plink: ESTAB > > It seems that routers are establishing connection on layer 2, but when I > try to ping they do not respond > I'm using ath9k driver and compat-wireless-2011-11-04.tar.bz2. > Have anyone had similar problem with ath9k + 802.11s in backfire from > trunk version? > > Thanks for your attention. > > Regards. > > -- > Rômulo Pinto de Albuquerque > > _______________________________________________ > Devel mailing list > [email protected] > http://open80211s.com/mailman/listinfo/devel > >
_______________________________________________ Devel mailing list [email protected] http://open80211s.com/mailman/listinfo/devel
