I will try the mcast-rate = 6; and let you know the results Thanks
On Mon, Nov 5, 2012 at 2:27 AM, Yeoh Chun-Yeow <[email protected]>wrote: > Hi, Fred > > If you are working with 5GHz card, please set the mcast-rate to at least > 6Mbps. > > mcast-rate = 6; > > --- > Chun-Yeow > > On Mon, Nov 5, 2012 at 3:19 PM, fred veldini <[email protected]> > wrote: > > Hello, > > > > I have been doing a lot more testing of the mesh links with authsae. I > have > > noticed a weird issue after reboots. > > > > Scenario: I have 6 mesh nodes running with the latest open80211s and > > authsae builds. I'm running on a ubuntu built kernel 3.5. I am using > the > > ath5k driver for ubiquiti XR5 cards. > > > > My layout is all six nodes are in equal range of each other and can > create a > > nice ESTAB with all units if I start one at a time. I built a startup > > script which creates the mesh interface and the starts authsae without > any > > errors. If I start with all nodes off and start one at a time everything > > works great. If I reboot one of the nodes after they successfully > connected > > I see 5 out of the 6 connections in LISTEN mode on the rebooted node. > All > > other nodes show the link as ESTAB. > > > > So investigating a little I found some things that stood out to me. Maybe > > they are correct or maybe not. > > > > If I reboot one node and watch another nodes station dump I see the > > rebooting node never gets released. Not sure if this is by design - but > > shouldn't the connection time out? > > > > I do notice the inactivity time going up until the node is back online > and > > the session is still showing ESTAB. After the rebooted node comes > online I > > check the node that showed the inactivity going up and now shows > inactivity > > as normal and ESTAB still in the list. I log into the rebooted node and > > check the station dump and it shows LISTEN. > > > > Here is the funny part if I manually start the mesh after reboot the same > > thing occurs, LISTEN state for connections > > But if I shut Authsae off and restart the same script (as above) to > create > > the mesh again everything comes up with ESTAB and works fine. > > > > I can recreate this scenario all the time. I have rebooted all units at > the > > same time to see what results we would get and most come up in LISTEN > mode. > > > > Here is a copy of my authsae.conf file > > ----------------- > > cut start > > ---------------- > > authsae: > > { > > sae: > > { > > debug = 480; > > password = "supersecret"; > > group = [19, 26, 21, 25, 20]; > > blacklist = 5; > > thresh = 5; > > lifetime = 3600; > > }; > > meshd: > > { > > meshid = "my-mesh"; > > interface = "mesh0"; > > passive = 0; > > debug = 1; > > mediaopt = 1; > > band = "11a"; > > channel = 157; > > htmode = "none"; > > mcast-rate = 1; > > }; > > }; > > --------------- > > cut end > > --------------- > > > > Thanks > > > > Fred > > > > _______________________________________________ > > Devel mailing list > > [email protected] > > http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel > > > _______________________________________________ > Devel mailing list > [email protected] > http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel >
_______________________________________________ Devel mailing list [email protected] http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel
