abhis...@abhishek-desktop:/backup/abhishek/Openmoko$ stty -F /dev/ttyUSB0 -a speed 115200 baud; rows 0; columns 0; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; eol2 = <undef>; swtch = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 5; -parenb -parodd cs8 hupcl -cstopb cread clocal -crtscts ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr -icrnl -ixon -ixoff -iuclc -ixany -imaxbel -iutf8 -opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 -isig -icanon -iexten -echo -echoe -echok -echonl -noflsh -xcase -tostop -echoprt -echoctl -echoke abhis...@abhishek-desktop:/backup/abhishek/Openmoko$
++++++++++++++++++++++++++++++++++++++++++++++++++ r...@om-gta02:~# stty -F /dev/ttySAC2 -a speed 115200 baud; rows 24; columns 80; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 5; -parenb -parodd cs8 -hupcl -cstopb cread clocal -crtscts ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr -icrnl -ixon -ixoff -iuclc -ixany -imaxbel -opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 -isig -icanon -iexten -echo -echoe -echok -echonl -noflsh -xcase -tostop -echoprt -echoctl -echoke r...@om-gta02:~# While both the minicom open settings are the same as shown above. But still having the same problem :( Thanks and Regards Abhishek bajpai 2009/6/9 Abhishek Bajpai <abhishei...@gmail.com> > > > 2009/6/9 Timo Juhani Lindfors <timo.lindf...@iki.fi> > >> Abhishek Bajpai <abhishei...@gmail.com> writes: >> > but I am not using getty instead I am using minicom with same baudrate. >> >> Did you check if the terminal settings are exactly same (stty -F >> /dev/ttySAC2 -a)? >> >> r...@om-gta02:~# stty -F /dev/ttySAC2 -a > speed 115200 baud; rows 24; columns 80; > intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; > eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; > lnext = ^V; flush = ^O; min = 1; time = 0; > -parenb -parodd cs8 -hupcl -cstopb cread clocal -crtscts > -ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon > -ixoff > -iuclc -ixany -imaxbel > opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 > ff0 > isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt > echoctl echoke > r...@om-gta02:~# > > +++++++++++++++++++++++++++++++++++++++++++++ > > > abhis...@abhishek-desktop:~$ stty -F /dev/ttyUSB0 -a > speed 9600 baud; rows 0; columns 0; line = 0; > intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; > eol2 = <undef>; swtch = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = > ^R; > werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; > -parenb -parodd cs8 hupcl -cstopb cread clocal -crtscts > -ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon > -ixoff > -iuclc -ixany -imaxbel -iutf8 > opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 > ff0 > isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt > echoctl echoke > abhis...@abhishek-desktop:~$ > > This shows that the settings are not same..... > but on minicom I am using same baudrate for both. Even If i change the > baudrates on both. I am able to get oneway response > > Computer>minicom ---> GTA02>minicom ----> Even I am getting some special > charactors echoed back on the Computer>minicom > > but not getting any response from > GTA02>minicom ----> Computer>minicom (No Response) > > > > > > > -- > " Even The word Impossible says I M Possible" > -- " Even The word Impossible says I M Possible"
_______________________________________________ devel mailing list devel@lists.openmoko.org https://lists.openmoko.org/mailman/listinfo/devel
