Hi Dr. Joel, I tried that in newlib/libc and there were at least no errors. (Nothing leading me to believe it was successful either!)
However I still got the same error when I sudo make install. (sparc-rtems-ranlib: command not found) (among others!) Thanks again! Sincerely, Matt On Wed, Jun 16, 2021 at 3:06 PM Joel Sherrill <j...@rtems.org> wrote: > > Does adding --no-recursive and running it only from the directory you touched > a build system file in help? > > It is regenerating a lot you don't want to touch anyway. > > --joel > > On Wed, Jun 16, 2021, 5:32 AM Matthew Joyce <mfjoyce2...@gmail.com> wrote: >> >> Hi Eshan, >> >> Thanks very much for your follow up! Ok, I see now that if I go into >> development/newlib/newlib-cygwin/newlib and run autoreconf -fvi with >> the v2.69 using the PATH that Dr. Joel just showed, it starts to run. >> It always eventually exits with an error though. (please see attached >> .txt). I hope you can read that...I used the command "script" to >> output everything to a text file. >> >> Do you have any idea where I might be going wrong? >> >> Thank you! >> >> Sincerely, >> >> Matt >> >> On Tue, Jun 15, 2021 at 8:23 PM Eshan Dhawan <eshandhawa...@gmail.com> wrote: >> > >> > Hi matt >> > It would work if run inside newlib instead of newlib-cygwin >> > run command inside of ../newlib-cygwin/newlib >> > instead of ../newlib-cygwin >> > >> > >> > On Tue, Jun 15, 2021 at 10:59 PM Matthew Joyce <mfjoyce2...@gmail.com> >> > wrote: >> >> >> >> Ah, ok will do! Thank you for the tip. >> >> >> >> On Tue, Jun 15, 2021 at 7:17 PM Gedare Bloom <ged...@rtems.org> wrote: >> >> > >> >> > Just a note, it's more efficient to capture your terminal dump into a >> >> > text file and attach that, rather than put a screenshot up. >> >> > >> >> > On Tue, Jun 15, 2021 at 11:14 AM Matthew Joyce <mfjoyce2...@gmail.com> >> >> > wrote: >> >> > > >> >> > > Hi Gentlemen, >> >> > > >> >> > > Thanks very much for your quick replies! >> >> > > >> >> > > I just tried both, but perhaps I'm misinterpreting your suggestions. >> >> > > (Could you please see the attached commands / errors!) >> >> > > >> >> > > Eshan, >> >> > > >> >> > > I did see that link, but it wasn't clear to me what the solution >> >> > > was...Sorry! >> >> > > >> >> > > Sincerely, >> >> > > >> >> > > Matt >> >> > > >> >> > > On Tue, Jun 15, 2021 at 6:52 PM Eshan Dhawan >> >> > > <eshandhawa...@gmail.com> wrote: >> >> > > > >> >> > > > Hi Matt, >> >> > > > Try running the command with autoconf version 2.69 that's shipped >> >> > > > with RTEMS in the rtems bin >> >> > > > That works as well. >> >> > > > >> >> > > > Also From a quick google search this is what I found : >> >> > > > https://superuser.com/questions/617872/cant-locate-autom4te-channeldefs-pm-in-inc-when-it-definitely-is-there >> >> > > > >> >> > > > On Tue, Jun 15, 2021 at 9:12 PM Matthew Joyce >> >> > > > <mfjoyce2...@gmail.com> wrote: >> >> > > >> >> >> > > >> Hello Dr. Joel and Eshan, >> >> > > >> >> >> > > >> I have a patch ready to send to Newlib for the sig function >> >> > > >> prototypes >> >> > > >> and STR2SIG_MAX. >> >> > > >> >> >> > > >> But to do that, I think I need to have Newlib built, which I must >> >> > > >> still be doing wrong. The error that I am getting is attached >> >> > > >> below. >> >> > > >> >> >> > > >> I’ve been trying to follow the steps here: >> >> > > >> https://medium.com/my-gsoc-2019-journey/apply-newlib-patch-to-rtems-source-builder-6873b0fb31b8 >> >> > > >> and >> >> > > >> https://medium.com/my-gsoc-2019-journey/build-newlib-for-sparc-and-arm-architecture-6b3287d4c6f2 >> >> > > >> >> >> > > >> I even had rebuilt everything from scratch to see if that would >> >> > > >> help, >> >> > > >> but I still get the same error. Maybe I cloned the newlib source >> >> > > >> into >> >> > > >> the wrong directory? >> >> > > >> >> >> > > >> I was hoping to get the patch off to Newlib for review as a first >> >> > > >> step >> >> > > >> while I work on writing the actual methods. When you get a moment, >> >> > > >> could you please advise? Thank you very much! >> >> > > >> >> >> > > >> Sincerely, >> >> > > >> >> >> > > >> Matt >> >> > > _______________________________________________ >> >> > > devel mailing list >> >> > > devel@rtems.org >> >> > > http://lists.rtems.org/mailman/listinfo/devel _______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel