On 18/10/2022 1:13 pm, Joel Sherrill wrote: > On Sun, Oct 16, 2022 at 9:32 AM Alan Cudmore <alan.cudm...@gmail.com > <mailto:alan.cudm...@gmail.com>> wrote: > > On Fri, Oct 14, 2022 at 9:19 AM Joel Sherrill <j...@rtems.org > <mailto:j...@rtems.org>> wrote: > > > > Pushed. Thanks for pinging. It does help. > > > > Since you are looking at the riscv BSPs, could you look at the four > > BSP build failures reported here: > > > > https://lists.rtems.org/pipermail/build/2022-September/036496.html > <https://lists.rtems.org/pipermail/build/2022-September/036496.html> > > > > I think they are all variants so one fix (maybe repeated) should do it. > > The reported message isn't much help: > > > > 1 smp riscv/rv32iac build: > > configure: /home/tester/rtems-cron-6/rtems/waf configure\ > > --prefix=/home/tester/rtems-cron-6/tools/6/bsps > --top=/home/tester\ > > /rtems-cron-6/rtems --rtems-config=config-riscv-rv32iac-smp.ini > > error: ld/collect2:0 error: no error message found! > > > > I ran the bsp builder on the riscv BSPs with an updated toolchain and > latest rtems master. I was able to reproduce only one of the failures > with the rv32imafdc SMP configuration: > Failures: > 1 smp riscv/rv32imafdc build: > configure: /home/alan/rtems/test-build/rtems/waf configure\ > --prefix=/home/alan/rtems/test-build/bsps\ > --top=/home/alan/rtems/test-build/rtems > --rtems-config=config-riscv-\ > rv32imafdc-smp.ini > error: ld/collect2:0 error: no error message found! > > Average BSP Build Time: 0:00:26.253927 > Total Time 1:04:45.581263 > Passes: 147 Failures: 1 > > This is the detail from the log: > [1424/1437] Compiling ../../../rtems/testsuites/samples/nsecs/init.c > start.o: in function `.L0 ': > > /home/alan/rtems/test-build/rtems/build/riscv/rv32imafdc/../../../bsps/riscv/shared/start/start.S:86:(.bsp_start_text+0x5 > c): relocation truncated to fit: R_RISCV_GPREL_I against symbol > `bsp_section_bss_size' defined in *ABS* section in /home/ > > alan/rtems/test-build/rtems/build/riscv/rv32imafdc/testsuites/samples/minimum.exe > collect2: error: ld returned 1 exit status > > This seems to be similar to the error I get when I try to build the > frdme310arty BSP with the testsuite and posix enabled: > [4152/4326] Compiling testsuites/validation/tr-sem-surrender.c > start.o: in function `.L0 ': > > /home/alan/rtems/test-build/rtems-tmp/build/riscv/frdme310arty/../../../bsps/riscv/shared/start/start.S:86:(.bsp_start_te > xt+0x28): relocation truncated to fit: R_RISCV_GPREL_I against symbol > `bsp_section_bss_size' defined in *ABS* section in > > /home/alan/rtems/test-build/rtems-tmp/build/riscv/frdme310arty/testsuites/validation/ts-validation-io-kernel.exe > collect2: error: ld returned 1 exit status > > I need to investigate this more. > > > There are two issues. > > (1) The test in question does not fit on this target and needs to be disabled. > > (2) Somewhere there is parsing of this output which may be able to be more > helpful. > > Chris... any pointers on (2)? Can the output of bsp builder be improved?
1) There should be a log of all the build details. Check in that for the error. 2) Can you build it by hand and see the error? Chris _______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel