On 11/25/2011 04:28 PM, Jamie Iles :
On Fri, Nov 25, 2011 at 02:51:06PM +0100, Jean-Christophe PLAGNIOL-VILLARD
wrote:
On 22:26 Thu 24 Nov , Jamie Iles wrote:
Hi Nicolas,
On Thu, Nov 24, 2011 at 10:56:27PM +0100, Nicolas Ferre wrote:
[...]
+#if defined(CONFIG_OF)
+static struct of_device_id aic_ids[] = {
+ { .compatible = "atmel,at91rm9200-aic" },
+ { /*sentinel*/ }
+};
+
+static int __init at91_aic_of_init(void)
+{
+ struct device_node *np;
+
+ np = of_find_matching_node(NULL, aic_ids);
+ if (np == NULL)
+ return -ENODEV;
+
+ at91_aic_base = of_iomap(np, 0);
+ at91_aic_domain.of_node = np;
I think this needs to be:
at91_aic_domain.of_node = of_node_get(np);
to keep the reference count.
Well, in fact the of_find_matching_node() function already indent the
ref. count...
+ /* Keep refcount of the node */
... That is why I added this comment ^^
But maybe for sake of clarity, I may have used what you propose anyway.
What it your opinion?
+
+ return 0;
+}
+#else
+static int __init at91_aic_of_init(void)
+{
+ return -ENOSYS;
+}
+#endif
I think it's preferred if you use of_irq_init() here as it can handle
the ordering of IRQ controllers. There are GIC and VIC bindings in
-next that use this and provide a way for non-DT platforms to still use
the drivers.
which is the case here as if the of_init fail we failback to the non-dt init
and this IP is AT91 only
Right, but it's not using the of_irq_init() interface which is the
standard way of registering interrupt controllers and will correctly
dependencies for you.
So if you could have something like:
void __init __at91_aic_init(unsigned int priority[NR_AIC_IRQS],
void __iomem *regs,
struct device_node *np)
{
/*
* Do all of the writes to the AIC itself and configure
* the IRQ domain.
*/
}
void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS])
{
void __iomem *base = ioremap(AT91_AIC, 512);
__at91_aic_init(priority, base, NULL);
}
int __init at91_aic_of_init(struct device_node *node,
struct device_node *parent)
{
void __iomem *regs = of_iomap(node, 0);
/*
* Get priorities from the DT. If this was an array of cells
* then that should be okay.
*/
__at91_aic_init(dt_priorities, regs, node);
}
Then the DT based board initialisation can do:
static const struct of_device_id at91_irq_of_match[] __initconst = {
{ .compatible = "atmel,at91-aic", .data = at91_aic_of_init },
{}
};
static void __init at91_of_irq_init(void)
{
of_irq_init(at91_of_irq_init);
}
That looks nice. I will try to implement this. I will try to figure out
when of_irq_init() is called compared to the other init_IRQ() function.
Which is consistent with other platforms. However this does require
that the priorities are encoded in the device-tree, but I guess that's a
good thing anyway isn't it?
That is a annoying point: I do not want to add all this "default"
priority stuff in the DT. It is kind of useless until we use the
threaded interrupts everywhere and may bloat the DT...
I will try to find a way to pass the default priority table to the DT
called function.
Thanks for your review,
--
Nicolas Ferre
_______________________________________________
devicetree-discuss mailing list
[email protected]
https://lists.ozlabs.org/listinfo/devicetree-discuss
